Installation Manual
Table Of Contents
- WAVEXpress/BTS Installation and Commissioning Guide
- One - Unpacking the WAVEXpress/BTS
- Two - Internal BTS Cabling and Jumpering
- Three - Installation
- 3-1 Wall Installation
- 3-2 Table Mount
- 3-3 Rack Installation
- 3-4 Common Final Installation Procedures
- 3-4.1 Connection of the Cable Gland
- 3-4.2 Connection of the Grounding Cable
- 3-4.3 Connection of the Antennas to the Bulkhead Plate
- 3-4.4 Connection of the Optional Combiner Assembly
- 3-4.5 Connection of the Power Supply
- 3-4.6 Connection of the T1 Lines
- 3-4.7 Connection to External Alarms
- 3-4.8 Optional Voltage Standing Wave Ratio (VSWR) Check
- 3-4.9 Post Installation Checks
- 3-5 Outdoor Installation
- Four - Off-Line Commissioning
- Five - Off-Line Commissioning of a Daisy Chain
- Six - Post Off-Line Commissioning
- Seven - On-Line Commissioning
- Appendix 1 - Connection of the Combiner Assembly
- Appendix 2 - BTS Field Maintenance
- A2-1 WAVEXpress/BTS Field Replacement Maintenance
- A2-1.1 Replacing the WAVEXpress/BTS IWP card
- A2-1.2 Replacing the WAVEXpress/BTS T1 card
- A2-1.3 Replacing the WAVEXpress/BTS TRX card
- A2-1.4 Replacing the WAVEXpress/BTS RF distribution card
- A2-1.5 Replacing the clock module
- A2-1.6 Replacing power supply units
- A2-1.7 Replacing fan assemblies
- A2-1.8 Replacing filters (p/n 520081-01)
- A2-1.9 Replacing the antenna bracket with a combiner assembly
- A2-1 WAVEXpress/BTS Field Replacement Maintenance
- Checklist 1 - Installation Checklist
- Checklist 2 - Commissioning Checklist
Release 3.3, Revision A 1/99
xv
interWAVE Parameter Dictionary
Scope
This dictionary is a reference guide that describes all objects and attributes used in WAVEView and in NMI, which is
the command line proprietary language used to manage interWAVE objects from the interWAVE Craft PC. For each
object, it includes a list of definitions, accepted ranges of values, default values, and comments that describe
correlations of attributes between the WAVEView and NMI.
Audience
This guide is intended for all personnel using interWAVE equipment.
interWAVE Glossary of Terms
Scope
The interWAVE Glossary of Terms
includes an alphabetical glossary of terms and lists the acronyms used by the
interWAVE products and documents.
Audience
This glossary allows an interWAVE trained field service engineer (FSE), the local operator, or other customer to look
up the technical terms used by interWAVE and GSM.
WAVEView Setup and System Administration Guide
Scope
The WAVEView hardware platform is delivered to a customer site with all appropriate software installed and with
factory set default values entered for all configurable parameters. Upon receipt of the system, the system
administrator must configure these parameters to correspond with those used in the network. The system
administrator also must perform basic routine maintenance at the operating system level to ensure that WAVEView is
functioning optimally, and that all data and databases are backed up in the event of system failure. The WAVEView
Setup and System Administration Guide details the routine tasks performed by a system administrator in a UNIX
environment.
This guide also describes the ‘behind-the scenes’ procedures that can be performed in-house if the software must be
re-installed or if the WAVEView OMC platform needs to be re-commissioned before integration into a pre-existing
network.
Audience
This guide is intended for the UNIX system administrator who will initially commission and maintain the WAVEView
software and will configure the WAVEView server and clients.