Installation Manual
Table Of Contents
- WAVEXpress/BTS Installation and Commissioning Guide
- One - Unpacking the WAVEXpress/BTS
- Two - Internal BTS Cabling and Jumpering
- Three - Installation
- 3-1 Wall Installation
- 3-2 Table Mount
- 3-3 Rack Installation
- 3-4 Common Final Installation Procedures
- 3-4.1 Connection of the Cable Gland
- 3-4.2 Connection of the Grounding Cable
- 3-4.3 Connection of the Antennas to the Bulkhead Plate
- 3-4.4 Connection of the Optional Combiner Assembly
- 3-4.5 Connection of the Power Supply
- 3-4.6 Connection of the T1 Lines
- 3-4.7 Connection to External Alarms
- 3-4.8 Optional Voltage Standing Wave Ratio (VSWR) Check
- 3-4.9 Post Installation Checks
- 3-5 Outdoor Installation
- Four - Off-Line Commissioning
- Five - Off-Line Commissioning of a Daisy Chain
- Six - Post Off-Line Commissioning
- Seven - On-Line Commissioning
- Appendix 1 - Connection of the Combiner Assembly
- Appendix 2 - BTS Field Maintenance
- A2-1 WAVEXpress/BTS Field Replacement Maintenance
- A2-1.1 Replacing the WAVEXpress/BTS IWP card
- A2-1.2 Replacing the WAVEXpress/BTS T1 card
- A2-1.3 Replacing the WAVEXpress/BTS TRX card
- A2-1.4 Replacing the WAVEXpress/BTS RF distribution card
- A2-1.5 Replacing the clock module
- A2-1.6 Replacing power supply units
- A2-1.7 Replacing fan assemblies
- A2-1.8 Replacing filters (p/n 520081-01)
- A2-1.9 Replacing the antenna bracket with a combiner assembly
- A2-1 WAVEXpress/BTS Field Replacement Maintenance
- Checklist 1 - Installation Checklist
- Checklist 2 - Commissioning Checklist
Release 3.3, Revision A 1/99
BTS Field Maintenance 117
Step 5
Using a Phillips screwdriver, unscrew the two screws located at the top and bottom of the RF distribu-
tion card.
Step 6
Remove the RF distribution card by firmly pulling the two white tabs located at the top and bottom of
the RF distribution card.
Step 7
Place the new RF distribution card into the slot (refer to Figure A3-1) and slide in the card until it com-
pletely rests inside the slot. Push the card firmly into place.
Step 8
Using a Phillips screwdriver, screw in the two removed screws onto the RF distribution card.
Figure A2-4:
RF distribution card semi-rigid cables layout (all RF semi-rigid cables are shown above)
TX
6.7
2,3
4,5
6,7
2,3
4,5
-1-
RX
RX
RX
TX
TX
CLK
PWR
ON
LINE
FLT
RX
TX
TEST RF DIST
-3-
-2-
PWR
ON
LINE
FLT
RX
TX
5[#7/8
7[#7/8
6HFRQG#DQWHQQD#FDEOH
050
&ORFN#FDEOH
5[#9/:
040
7[#9/:
5)#'LVW0
75;#FDEOHV
)LUVW#DQWHQQD#FDEOH
5)#'LVWULEXWLRQ#FDUG
75;#FDUGV
PWR
ON
LINE
FLT
RX
TX
5[#5/6
7[#5/6
060
7KLUG#DQWHQQD#FDEOH