Instruction Manual

ManualsBrandsADC Telecommunications ManualsElectronicsInterReach Fusion FSN-809019-1

121

122

123

124

125

126

127

128

129

130

Table Of Contents

SECTION 1 General Information
- 1.1 Firmware Release
- 1.2 Purpose and Scope
- 1.3 Conventions in this Manual
- 1.4 Standards Conformance
- 1.5 Related Publications
SECTION 2 InterReach Fusion System Description
- 2.1 System Overview
- 2.2 System Hardware Description
- 2.3 System OA&M Capabilities Overview
  - 2.3.1 System Monitoring and Reporting
  - 2.3.2 Using Alarm Contacts
- 2.4 System Connectivity
- 2.5 System Operation
- 2.6 System Specifications
  - 2.6.1 RF End-to-End Performance
SECTION 3 Fusion Main Hub
- 3.1 Fusion Main Hub Front Panel
- 3.2 Fusion Main Hub Rear Panel
  - 3.2.1 Fusion Main Hub Rear Panel Connectors
    - 3.2.1.1 9-pin D-sub Connector
    - 3.2.1.2 N-type Female Connectors
- 3.3 Main Hub Specifications
- 3.4 Faults, Warnings, and Status Messages
  - 3.4.1 Description
  - 3.4.2 View Preference
SECTION 4 Fusion Expansion Hub
- 4.1 Expansion Hub Overview
- 4.2 Expansion Hub Front Panel
- 4.3 Expansion Hub Rear Panel
- 4.4 Faults, Warnings, and Status Messages
- 4.5 Expansion Hub Specifications
SECTION 5 Remote Access Unit
- 5.1 RAU Overview
- 5.2 Remote Access Unit Connectors
  - 5.2.1 50 Ohm Type-N Connector
  - 5.2.2 75 Ohm Type-F Connector
- 5.3 RAU LED Indicators
- 5.4 Faults and Warnings
- 5.5 Remote Access Unit Specifications
SECTION 6 Designing a Fusion Solution
- 6.1 Overview
- 6.2 Downlink RSSI Design Goal
- 6.3 Maximum Output Power per Carrier
- 6.4 System Gain
  - 6.4.1 System Gain (Loss) Relative to CATV Cable Type Length
- 6.5 Estimating RF Coverage
- 6.6 Link Budget Analysis
- 6.7 Optical Power Budget
- 6.8 Connecting a Main Hub to a Base Station
  - 6.8.1 Uplink Attenuation
  - 6.8.2 RAU Attenuation and ALC
    - 6.8.2.1 Using the RAU 10 dB Attenuation Setting
    - 6.8.2.2 Using the Uplink ALC Setting
SECTION 7 Installing Fusion
- 7.1 Installation Requirements
- 7.2 Safety Precautions
- 7.3 Preparing for System Installation
- 7.4 Fusion Installation Procedures
- 7.5 Splicing Fiber Optic Cable
  - 7.5.1 Fusion Splices
- 7.6 Interfacing the Fusion Main Hub to an RF Source
  - 7.6.1 Connecting a Single Fusion Main Hub to an RF Source
  - 7.6.2 Connecting Multiple Fusion Main Hubs to an RF Source
- 7.7 Connecting Contact Alarms to a Fusion System
- 7.8 Alarm Monitoring Connectivity Options
SECTION 8 Replacing Fusion Components
- 8.1 Replacing an RAU
- 8.2 Replacing a Fusion Expansion Hub
- 8.3 Replacing a Fusion Main Hub
SECTION 9 Maintenance, Troubleshooting, and Technical Assistance
- 9.1 Service
- 9.2 Maintenance
- 9.3 Troubleshooting
- 9.4 Troubleshooting CATV
- 9.5 Technical Assistance
APPENDIX A Cables and Connectors
A.1 75 Ohm CATV Cable
A.2 Fiber Optical Cables
A.3 Coaxial Cable
A.4 Standard Modem Cable
A.5 TCP/IP Cross-over Cable
A.6 DB-25 to DB-9 Null Modem Cable
APPENDIX B Compliance
B.1 Fusion System Approval Status
B.2 Human Exposure to RF
APPENDIX C Faults, Warnings, Status Tables
C.1 Fault Messages Reported by Hubs
C.2 Faults Reported for System CPU
C.3 Faults for RAUs
C.4 Warning/Status Messages for Hubs
C.5 Warning/Status Messages for System CPUs
C.6 Warning /Status Messages for RAUs

Help Hot Line (U.S. only): 1-800-530-9960 7-19

D-620TBD-0-20 Rev A CONFIDENTIAL

Fusion Installation Procedures

7.4.2 Installing Expansion Hubs

The Expansion Hub (2U high) can be installed in a standard 19 in. (483 mm) equip-

ment rack or in a wall-mountable equipment rack that is available from LGC Wire-

less. Allow a clearance of 76 mm (3 in.) front and rear and 51 mm (2 in.) sides for air

circulation. No top and bottom clearance is required.

CAUTION: Install Expansion Hubs in indoor locations only.

Installing an Expansion Hub in a Rack

Consideration:

• The Expansion Hub is shipped with #10-32 mounting screws. Another common

rack thread is #12-24. Confirm that the mounting screws match the rack’s threads.

• If you want to move the mounting brackets to a mid-mounting position, refer to

Installing a Main Hub Using the 12” Wall-Mounted Rack (PN 4712) on page 7-12.

To install the hub in a rack:

1. Insert spring nuts into the rack where needed or use existing threaded holes.

2. Place the Expansion Hub into the rack from the front.

3. Align the flange holes with the spring nuts installed in Step 1.

4. Insert the mounting screws in the appropriate positions in the rack.

5. Tighten the mounting screws.