User's Guide

ManualsBrandsADC Telecommunications ManualsElectronicsInterReach FusionÂ® Wideband

111

112

113

114

115

116

117

118

119

120

Table Of Contents

SECTION 1 General Information
- 1.1 Firmware Release
- 1.2 Purpose and Scope
- 1.3 Conventions in this Manual
- 1.4 Standards Conformance
- 1.5 Related Publications
SECTION 2 InterReach Fusion System Description
- 2.1 System Overview
- 2.2 System Hardware Description
- 2.3 System OA&M Capabilities Overview
  - 2.3.1 System Monitoring and Reporting
  - 2.3.2 Using Alarm Contacts
- 2.4 System Connectivity
- 2.5 System Operation
- 2.6 System Specifications
  - 2.6.1 RF End-to-End Performance
SECTION 3 Fusion Main Hub
- 3.1 Fusion Main Hub Overview
- 3.2 Fusion Main Hub Front Panel
- 3.3 Fusion Main Hub Rear Panel
  - 3.3.1 Fusion Main Hub Rear Panel Connectors
    - 3.3.1.1 9-pin D-sub Connector
    - 3.3.1.2 N-type Female Connectors
- 3.4 Main Hub Specifications
- 3.5 Faults, Warnings, and Status Messages
  - 3.5.1 Description
  - 3.5.2 View Preference
SECTION 4 Fusion Expansion Hub
- 4.1 Expansion Hub Overview
- 4.2 Expansion Hub Front Panel
- 4.3 Expansion Hub Rear Panel
- 4.4 Faults, Warnings, and Status Messages
- 4.5 Expansion Hub Specifications
SECTION 5 Remote Access Unit
- 5.1 RAU Overview
- 5.2 Remote Access Unit Connectors
  - 5.2.1 50 Ohm Type-N Connector
  - 5.2.2 75 Ohm Type-F Connector
- 5.3 RAU LED Indicators
- 5.4 Faults and Warnings
- 5.5 Remote Access Unit Specifications
SECTION 6 Designing a Fusion Solution
- 6.1 Overview
- 6.2 Downlink RSSI Design Goal
- 6.3 Maximum Output Power per Carrier
- 6.4 System Gain
- 6.5 Estimating RF Coverage
- 6.6 Link Budget Analysis
- 6.7 Optical Power Budget
- 6.8 Connecting a Main Hub to a Base Station
  - 6.8.1 Uplink Attenuation
  - 6.8.2 RAU Attenuation and ALC
    - 6.8.2.1 Using the RAU 10 dB Attenuation Setting
    - 6.8.2.2 Using the Uplink ALC Setting
SECTION 7 Installing Fusion
- 7.1 Installation Requirements
- 7.2 Safety Precautions
- 7.3 Preparing for System Installation
- 7.4 Fusion Installation Procedures
- 7.5 Splicing Fiber Optic Cable
- 7.6 Interfacing the Fusion Main Hub to an RF Source
  - 7.6.1 Connecting a Single Fusion Main Hub to an RF Source
  - 7.6.2 Connecting Multiple Fusion Main Hubs to an RF Source
- 7.7 Connecting Contact Alarms to a Fusion System
- 7.8 Alarm Monitoring Connectivity Options
SECTION 8 Replacing Fusion Components
- 8.1 Replacing an RAU
- 8.2 Replacing a Fusion Expansion Hub
- 8.3 Replacing a Fusion Main Hub
SECTION 9 Maintenance, Troubleshooting, and Technical Assistance
- 9.1 Service
- 9.2 Maintenance
- 9.3 Troubleshooting
  - 9.3.1 Troubleshooting Using AdminBrowser
    - 9.3.1.1 Troubleshooting Recommendations
    - 9.3.1.2 Fault/Warning/Status Indications
  - 9.3.2 Troubleshooting Using LEDs
    - 9.3.2.1 Troubleshooting Main Hub LEDs During Normal Operation
    - 9.3.2.2 Troubleshooting Expansion Hub LEDs During Normal Operation
- 9.4 Troubleshooting CATV
- 9.5 Technical Assistance
APPENDIX A Cables and Connectors
A.1 75 Ohm CATV Cable
A.2 Fiber Optical Cables
A.3 Coaxial Cable
A.4 Standard Modem Cable
A.5 TCP/IP Cross-over Cable
A.6 DB-25 to DB-9 Null Modem Cable
APPENDIX B Compliance
B.1 Fusion System Approval Status
B.2 Human Exposure to RF
APPENDIX C Faults, Warnings, Status Tables
C.1 Faults Reported by Fusion Main/SingleStar Hubs
C.2 Faults Reported for System CPU
C.3 Faults for Fusion Expansion Hubs
C.4 Faults for RAUs
C.5 Warning/Status Messages for Fusion Main/SingleStar Hubs
C.6 Warning/Status Messages for System CPUs
C.7 Warning/Status Messages for Fusion Expansion Hubs
C.8 Warning /Status Messages for RAUs

Help Hot Line (U.S. only): 1-800-530-9960 7-9

D-620610-0-20 Rev B CONFIDENTIAL

Preparing for System Installation

7.3.4 Optional Accessories

Table 7-4 Optional Accessories for Component Installation

Description

Wall-mount bracket (PN 4712)

When using this bracket with an Fusion Main Hub, the Hub’s mounting bracket must

be moved to the alternate mounting position (refer to the procedure on page

page 7-11).

Cable management (Cable manager: PN 4759; Tie wrap bar: PN 4757)

Splice trays

Pigtails with SC/APC connectors, 3 m (10 ft.)

Multi-mode fiber SC/APC pigtail: PN 402SCAPC-10

Single-mode fiber SC/APC pigtail: PN 4013SCAPC-10

Jumper cable when Main and Expansion Hubs are collocated, 3 m (10 ft.)

Multi-mode fiber SC/APC: PN 4018SCAPC-10

Teltone Line Sharing Switch (M-394-B-01)

When using a single POTS line with multiple Fusion Main Hub/Modems: Connect up

to four modems to a line sharing switch; switches can be cascaded to accommodate up

to 16 modems per POTS line

Alarm Cables:

5-port Alarm Daisy-Chain Cable (PN 4024-3)

Alarm Sense Adapter Cable (PN 4025-1)