User's Manual Part 2

Appendix C: Faults, Warnings, Status Tables for Fusion, Fusion Wideband, Fusion SingleStar
Page 210 InterReach Fusion Wideband Installation, Operation, and Reference Manual
© 2013 TE Connectivity Ltd D-620616-0-20 Rev H • TECP-77-044 Issue 7 • May 2013
FAULTSREPORTEDBYMAINHUBS
Faultsindicateservice‐impactingconditionsandshouldbegivenimmediateattention.
Oncealloftheunitsarepoweredonandthecableconnectionsar
emade,thefaultsfromeachunit
canberequestedusingAdminBrowser.StartwiththeFusionorFusionWidebandMainHuband
workdownstream.
Resolveallfaultsfirstandthencheckthewarnings.Takeappropriate
actiontoresolvethefaults,
asindicatedinthefollowingtables.Incaseswherethereismorethanonepossiblecause,theyare
listedfromthe“mostlikely”tothe“leastlikely”cause.Actionsarelistedintheorderthatthey
shouldbeperformed;notallactionsmayneedtobedone.
NOTE: IfyouhavearedSTATUSLEDwithoutafaultmessage,itprobab lyindicatesthattheunitislocked
out.
Table98. FaultMessagesforMainHubs
Message
Number
Description Reason/Action
{MF01} Software error occurred and recovered. If this happens repeatedly, replace the Hub.
{MF02} Software error occurred and recovered. If this happens repeatedly, replace the Hub.
{MF03} Software error occurred and recovered. If this happens repeatedly, replace the Hub.
{MF04} Software reset occurred and reco
vered, or firmware
download.
If this happens repeatedly, replace the Hub.
{MF05} Software error occurred and recovered. If this happens repeatedly, replace the Hub.
{MF06} Problem detected in the Hub. Internal communication
reset.
Contact TE Support for more information.
{MF07} Hub power cycle. Hub power cycle.
{MF08} Internal communications failure. No internal communications in preceding 15 minutes.
{MF09} Hardware Reset. Commanded hardware power on reset
{MF10} Band not programmed. Use AdminBrowser to program the band.
{MF11} Hardware failure (DL Pilot PLL). Cycle power once. If fault persists, replace
the Hub
{MF12} Hardware failure (DL Pilot Too High). Cycle power once. If fault persists, replace
the Hub.
{MF13} Hardware failure (DL Pilot Too Low). Cycle power once. If fault persists, replace
the Hub.
{MF14} Hardware failure (54 VDC). 54 VDC power supply is out of range, replace the Hub
{MF15} Hardware failure (RF VDC Power). Loss of DC power to RF circ
uits, replace the Hub.
{MF16} Self Lockout (All Bands). Hub has shutdown the system due to an inte
rnal fault.
System is offline.
{MF17} Hardware failure (DL PLL Band 1). Cycle power once. If fault persists, replace
the Hub.
{MF18} Hardware failure (UL PLL Band 1). Cycle power once. If fault persists, replace
the Hub
{ML19} Commanded Out-of-servi
ce (Band 1). Band 1 commanded out-of-service by User.
{MF20} Hardware failure (UL1 LO2 Band 1). Cycle power once. If the fault persists, replace the Hub.
{MF21} Problem detected in the Hub. Contact TE Support for more information.
{MF22} Problem detected in the Hub. Contact TE Support for more information.
{MF23} Problem detected in the Hub Contact TE Support for more information.
{MF24} Problem detected in the Hub. Contact TE Support for more information.
{MF25} Hardware failure (DL PLL Band 2). Cycle power once. If fault persists, replace
the Hub.