User's Manual Part 1

ManualsBrandsADC Telecommunications ManualsElectronicsDigivance Long Range Coverage Solution 800 MHz Sys

Table Of Contents

DRAFT

ADCP-75-124

Issue B

April 2002

1209926 Rev A

(Digivance™ Long-Range Coverage Solution

Single Band 800 MHz System

(Installation and Operation Manual

17024-A

FCC ID: F8I-DVLRCS800 - User Manual Part 1

Summary of content (30 pages)

PAGE 1
DRAFT FCC ID: F8I-DVLRCS800 - User Manual Part 1 ADCP-75-124 Issue B April 2002 (Digivance™ Long-Range Coverage Solution Single Band 800 MHz System (Installation and Operation Manual 17024-A 1209926 Rev A
PAGE 2
DRAFT ADCP-75-124 Issue B April 2002 (Digivance™ Long-Range Coverage Solution Single Band 800 MHz System (Installation and Operation Manual 1209926 Rev A
PAGE 3
ADCP-75-124 • Issue B • April 2002 • Preface COPYRIGHT © 2002, ADC Telecommunications, Inc. All Rights Reserved Printed in the U.S.A. REVISION HISTORY ISSUE DATE B 04/2002 REASON FOR CHANGE Original issue. TRADEMARK INFORMATION ADC and PowerWorx are registered trademarks of ADC Telecommunications, Inc. Digivance is a trademark of ADC Telecommunications, Inc. Procomm Plus is a registered trademark of Quarterdeck Corporation.
PAGE 4
ADCP-75-124 • Issue B • April 2002 • Preface TABLE OF CONTENTS Content Page ABOUT THIS MANUAL . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . vii RELATED PUBLICATIONS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . vii ADMONISHMENTS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
PAGE 5
ADCP-75-124 • Issue B • April 2002 • Preface TABLE OF CONTENTS Content 4 Page 3.1 Primary Components . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-8 3.2 Mounting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-8 3.3 Module Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
PAGE 6
ADCP-75-124 • Issue B • April 2002 • Preface TABLE OF CONTENTS Content Page 4 HU MOUNTING PROCEDURE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3-6 5 CHASSIS GROUND CONNECTION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3-8 6 COAXIAL CABLE CONNECTIONS. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
PAGE 7
ADCP-75-124 • Issue B • April 2002 • Preface TABLE OF CONTENTS Content Page 5.4 Spectrum Transport Module Fan Replacement Procedure . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-17 5.5 Linear Power Amplifier Fan Replacement Procedure . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-19 SECTION 6: GENERAL INFORMATION 1 WARRANTY/SOFTWARE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
PAGE 8
ADCP-75-124 • Issue B • April 2002 • Preface ABOUT THIS MANUAL This installation and operation manual provides the following information: • An overview of the Digivance Single Band 800 MHz Long-Range Coverage Solution (LRCS). • A description of the basic system components including the Host Unit (HU), Spectrum Transport Module (STM), Linear Power Amplifier (LPA), Remote Unit (RU) cabinet, and Digivance Element Management System (EMS). • Installation procedures for the HU.
PAGE 9
ADCP-75-124 • Issue B • April 2002 • Preface ADMONISHMENTS Important safety admonishments are used throughout this manual to warn of possible hazards to persons or equipment. An admonishment identifies a possible hazard and then explains what may happen if the hazard is not avoided. The admonishments — in the form of Dangers, Warnings, and Cautions — must be followed at all times.
PAGE 10
ADCP-75-124 • Issue B • April 2002 • Preface STANDARDS CERTIFICATION FCC: This equipment complies with the applicable sections of Title 47 CFR Part 22. UL/CUL: This equipment complies with UL and CUL 50 Standard for Enclosures for Electrical Equipment. This equipment provides the degree of protection specified by IP43 as defined in IEC Publication 529. FDA/CDRH: This equipment uses a Class 1 LASER according to FDA/CDRH Rules. This product conforms to all applicable standards of 21 CFR Part 1040.
PAGE 11
ADCP-75-124 • Issue B • April 2002 • Preface HU IC LED LPA LRCS MHz MI MPE MTBF NC NEM NO NOC NPT OSP PA PC PCS Prg Pwr Rev RF RIM RMA RU RX SMR STM TX UL VAC VDC VSWR WECO WDM Page x © 2002, ADC Telecommunications, Inc.
PAGE 12
ADCP-75-124 • Issue B • April 2002 • Section 1: Overview SECTION 1: OVERVIEW 1 INTRODUCTION. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1-1 2 SINGLE BAND SYSTEM OVERVIEW . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1-1 3 2.1 Basic Components . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
PAGE 13
ADCP-75-124 • Issue B • April 2002 • Section 1: Overview EBTS RF CD-ROM WITH EMS SOFTWARE HOST UNIT CONTROLLER AREA NETWORK NETWORK OPERATIONS CENTER (REMOTE INTERFACE) REMOTE UNIT LAPTOP (LOCAL INTERFACE) EBTS RS-232 RF HOST UNIT REMOTE UNIT DATA NETWORK EBTS RS-232 ASCII RF RS-232 HOST UNIT DIGIVANCE ELEMENT MANAGEMENT SYSTEM REMOTE UNIT 16969-B Figure 1-1. System Overview Diagram 2.
PAGE 14
ADCP-75-124 • Issue B • April 2002 • Section 1: Overview 2.3 Handset Interface The RU interfaces with the handsets through an antenna. In the reverse path, the RU receives RF signals from each handset. The RU digitizes the RF signals and then converts them to digital optical signals for transport to the HU. In the forward path, the RU receives digital optical signals from the HU. The RU converts the optical signals to RF signals for transmission to the handsets.
PAGE 15
ADCP-75-124 • Issue B • April 2002 • Section 1: Overview 3 SYSTEM FUNCTIONS AND FEATURES This section describes various system level functions and features of the Digivance LRCS. 3.1 Fiber Optic Transport On an optional basis, the Digivance LRCS is available either with or without reverse path diversity. On non-diversity systems that do not use a WDM module, the HU is connected to the RU over a pair of single-mode optical fibers. One fiber is used to transport the forward path optical signal.
PAGE 16
ADCP-75-124 • Issue B • April 2002 • Section 1: Overview EBTS COAX FIBER OPTIC LINK HOST UNIT REMOTE UNIT FORWARD PATH PRIMARY REVERSE PATH DIVERSITY REVERSE PATH 16997-A Figure 1-3. Fiber Optic Transport with Diversity and Without WDM Module The optical wavelengths used in the system are 1550 nm for the forward path and 1310 nm for the reverse path.
PAGE 17
ADCP-75-124 • Issue B • April 2002 • Section 1: Overview Because separate forward and reverse path optical inputs and outputs are provided at the HU and RU, a Free Space Optics (FSO) system (that meets the Digivance LRCS data rate performance and BER requirements) may be used in applications where it is desirable to bridge an open span and where it is impractical to lay a fiber optic cable.
PAGE 18
ADCP-75-124 • Issue B • April 2002 • Section 1: Overview 3.4 Powering The HU is powered by ±24 or ±48 Vdc and must be hard-wired to a local office battery power source through a fuse panel. The RU is powered by 120 or 240 Vac (50 or 60 Hz) and must be hard-wired to the AC power source through a 20 Amp breaker box. The RU is pre-wired for 120 Vac operation but can be converted to 240 Vac operation if required.
PAGE 20
ADCP-75-124 • Issue B • April 2002 • Section 2: Description SECTION 2: DESCRIPTION Content Page 1 INTRODUCTION. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2-2 2 HOST UNIT . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2-2 2.1 Primary Components . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
PAGE 21
ADCP-75-124 • Issue B • April 2002 • Section 2: Description 6 7 DIGIVANCE ELEMENT MANAGEMENT SYSTEM . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-19 6.1 Primary Components . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-19 6.2 Service Interface Connection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-20 6.
PAGE 22
ADCP-75-124 • Issue B • April 2002 • Section 2: Description 17.2 INCHES (437 mm) FRONT PANEL MOUNTING BRACKET (BOTH SIDES) 3.5 INCHES (89 mm) 11.4 INCHES (290 mm) 15.3 INCHES (389 mm) CABLE MANAGEMENT TRAY 16796-A Figure 2-1. Host Unit 2.2 Mounting The HU is intended for rack-mount applications. A pair of reversible mounting brackets is provided that allow the HU to be mounted in either a 19-inch or 23-inch EIA or WECO equipment rack.
PAGE 23
ADCP-75-124 • Issue B • April 2002 • Section 2: Description most installations, it is usually necessary to install an external attenuator in the forward path link between the HU and the BTS. The HU should be as close as possible to the BTS to minimize cable losses. 2.5 RF Signal Level Adjustments The HU is equipped with several attenuators for adjusting the signal levels of the forward and reverse path RF signals.
PAGE 24
ADCP-75-124 • Issue B • April 2002 • Section 2: Description 2.10 Powering The HU is powered by ± 24 or ± 48 Vdc power. The power is fed to the HU through a screwdown type terminal strip located on the rear side of the unit. Power to the HU must be supplied through a fuse panel such as the 20 position PowerWorx fuse panel (available separately). The power circuit for each HU must be protected with a 3 Amp GMT fuse. An On/Off switch is provided on the HU front panel. 2.
PAGE 25
ADCP-75-124 • Issue B • April 2002 • Section 2: Description Table 2-1. Host Unit User Interface, continued REF NO USER INTERFACE DESIGNATION DEVICE FUNCTIONAL DESCRIPTION 3 PORT 2 SC connector (single-mode) Connection point for the reverse path primary optical fiber. 4 PORT 3 (diversity unit only) SC connector (single-mode) Connection point for the reverse path diversity optical fiber. 5 POWER Multi-colored LED (green/yellow) Indicates if the HU is powered (green) or unpowered (off).
PAGE 26
ADCP-75-124 • Issue B • April 2002 • Section 2: Description 3 REMOTE UNIT CABINET The RU cabinet, shown in Figure 2-3, is a NEMA-3R enclosure (with removable dust filter) that provides the following basic functions: • Houses the various electronic modules (STM and LPA) and accessories (back-up battery kit and WDM kit) and protects them from the weather. • Provides electrical interface connections for the STM and LPA modules.
PAGE 27
ADCP-75-124 • Issue B • April 2002 • Section 2: Description 3.1 Primary Components The RU cabinet consists of the enclosure, a mounting shelf for the STM and LPA modules, an AC power interface, a lightning protector, a mounting shelf for the back-up battery accessory, a fiber storage spool, and a mounting bracket for the WDM accessory. The RU cabinet is designed for use in either an outdoor or indoor environment.
PAGE 28
ADCP-75-124 • Issue B • April 2002 • Section 2: Description 23 mm) in diameter. A spool is provided directly above the fiber optic cable entry hole for storing excess pigtail slack. In a typical installation, the connectorized end of a mulit-fiber outside plant cable is routed into the enclosure through the cord connector and the individual fibers are broken out into pigtails. The pigtails are connected to the optical ports on the STM and the excess pigtail slack is stored on the fiber storage spool.
PAGE 29
ADCP-75-124 • Issue B • April 2002 • Section 2: Description current to maintain the battery charge level. During an AC power outage, the battery provides DC power to the STM to maintain system operation. The battery can maintain operation of the RU for approximately 1 hour at 50 Watts. 3.8 Ventilation Vent openings are provided in the door and the rear side of the RU cabinet to permit air exchange for cooling. Air enters the enclosure through the opening in the door.
PAGE 30
ADCP-75-124 • Issue B • April 2002 • Section 2: Description (2) AC POWER CORD (1) AIR INLET FILTER (3) CIRCUIT BREAKER RESET SWITCH (4) DOOR SWITCH (7) GFCI OUTLET (9) LIGHTNING PROTECTOR (5) MODULE MOUNTING SHELF (6) BATTERY TRAY (8) FIBER SLACK SPOOL BOTTOM VIEW OF CABINET 16793-B (10) FIBER CABLE CONNECTOR (11) THREADS FOR AC CONDUIT FITTING (12) GROUNDING LUG Figure 2-4. Remote Unit Cabinet User Interface Page 2-11 © 2002, ADC Telecommunications, Inc.