User's Manual
Table Of Contents
- interWave WaveNet Link CX User Manual
- One - System Description
- 1-1 General
- 1-2 System Overview
- 1-3 Features
- 1-4 LinkCX Basic Structure
- 1-4.1 Radio Links
- 1-4.2 Data Stream
- 1-4.3 LinkCX Models
- 1-4.4 Mounting and Antenna Alignment
- 1-4.5 Interface Connectors and Indicators
- 1-4.6 Cables
- 1-4.7 Integral Antenna
- 1-4.8 External Antenna
- 1-4.9 Configuration, Operation, and Monitoring
- 1-4.10 SNMP
- 1-4.11 LinkCX Network Management Architecture
- 1-4.12 NMS Connectivity
- 1-4.13 Web-Based GUI Access Security
- 1-4.14 GUI Functions
- 1-5 Typical Applications
- 1-5.1 Internet (ISP)
- 1-5.2 Private Network Wireless Bridged LANs and WANs
- 1-5.3 PCS/PCN and Cellular Networks
- 1-5.4 Wireless Local Loop Networks and Local Exchange Bypass
- 1-5.5 Business Bypass and Local Exchange Bypass
- 1-5.6 Backhaul for Wireless MTU and MTU Access
- 1-5.7 Wireless Mesh Backhaul Networks
- 1-5.8 Wireless ATM Mesh Distribution with StreamNet
- 1-6 Specifications
- Two - Installation Steering Guide
- Three - Installation Planning
- Four - Installing the Link CX
- Five - Final Link CX Setup
- Six - Monitoring and Trend Analysis
- Seven - Troubleshooting the Link CX
- Appendix 1 - Interface Cable Pinouts
- Appendix 2 - Technical Specifications
- Appendix 3 - Using the Web-Based GUI User Interface
- Appendix 4 - Grounding and Lightning Protection
- Appendix 4 - Enterprise MIBs and Traps
Enterprise MIBs and Traps 117
A value of 1 indicates the Rx synthesizer is locked.
A value of 2 indicates the Rx synthesizer is unlocked"
::= }link_cx_status 6}
lowTxPowerAlarmStatus OBJECT-TYPE -- local alarm condition
SYNTAX INTEGER {
normal(1),
alarm(2)
}
ACCESS read-only
STATUS mandatory
DESCRIPTION
"A value of 1 indicates the Tx power at the antenna port
is greater than or equal to -14 dBm. A value of 2 indicates
the Tx power at the antenna port is less than -14 dBm."
::= }link_cx_status 7}
demodLockAlarmStatus OBJECT-TYPE -- link alarm condition
SYNTAX INTEGER {
normal(1),
alarm(2)
}
ACCESS read-only
STATUS mandatory
DESCRIPTION
"The demodulator lock status.
A value of 1 indicates the demodulator is locked.
A value of 2 indicates the demodulator is unlocked"
::= }link_cx_status 8}
lowRssiLevelAlarmStatus OBJECT-TYPE -- link alarm condition
SYNTAX INTEGER {
normal(1),
alarm(2)
}
ACCESS read-only
STATUS mandatory
DESCRIPTION
"A RSSI alarm will be generated if the level of RSSI goes below
the user configured RSSI alarm level, rfRssiAlarmThresholdSetting.
A value of 1 indicates the received signal level is above the RSSI
alarm threshold. A value of 2 indicates the received signal level
is at or below the user configured RSSI alarm level.
This alarm is valid only if the Rx synthesizer is locked."
::= }link_cx_status 9}
receiverOverloadAlarmStatus OBJECT-TYPE -- link alarm condition
SYNTAX INTEGER {
normal(1),
alarm(2)
}