Manual

ManualsBrandsAdaptive Technologies ManualsVideo4X4-UD55A-VWD

Left Frame

(

ure 1A

)

4X4-UD55A-VWD

Assembly Installation Guide

Important: Assembling video displays is a serious

endeavor that requires experienced professionals.

Improperly assembled equipment can result in

property damage, injury and/or liability to the

installing contractor. Do not attempt to install this

equipment if any part of the assembly is in doubt.

Follow these instructions for the most efficient and

safest assemble results.

Do not attempt to install this product if any of the

parts listed below are missing. If parts are missing,

contact sales@adapttechgroup.com;

Package Contents:

7 pcs 9-0881 4X Left H-Slat

7 pcs 9-0883 4X Right H-Slat

2 pcs 9-0893 bottom Side H- slat

2 pcs 9-0895 bottom center H- Slat

12 pcs 9-0885 V-Channel Assembly

2 PCS 9-0890 Center V-Channel assembly

8 pcs 9-0888 Lock Arm Bracket

8 pcs 9-0806 Horizontal Joiner plate

6 pcs 9-0897 Vertical Joiner Plate

8 pcs Nylon/friction washer,.28 IDx.74OD, white

8 pcs Phil. Pan head screw, M4-12mm long

8 pcs Nyloc nut, M4

272 pcs Flat head phil. Screw, M6x20mm long

Top right Frame (Figure 1B)

Summary of content (10 pages)

PAGE 1
4X4-UD55A-VWD Assembly Installation Guide Important: Assembling video displays is a serious endeavor that requires experienced professionals. Improperly assembled equipment can result in property damage, injury and/or liability to the installing contractor. Do not attempt to install this equipment if any part of the assembly is in doubt. Follow these instructions for the most efficient and safest assemble results. Do not attempt to install this product if any of the parts listed below are missing.
PAGE 2
Step 1: Assemble Top Left Frame Place all of the parts in figure 1A on the floor. Start with three 9-0885 V-channels with their open side facing up with the narrow part of the key holes slots facing up and all in the same direction. Place four 9-0881 Left H-Slats over the Vchannels with the keyhole surface facing up and the fourhole patterns lining up with that of the channels (Figure 1A). Rectangular slots in the ends of the slats should be at the outer edge of the frame. (See figure 3).
PAGE 3
Step 6: Install Locking Arm brackets Assemble the 9-0888 locking arm bracket on three of the 9-0881 left H-slat and three on the 9-0883 right H-slat near the rectangular slot using the provided M4 screws, nylon washer and nylock nut (Figure 4). The locking arm brackets must be installed on the first, third, fifth and seventh horizontal Hslats starting from the top. Make sure the hook of the locking arm bracket faces up (Figure 4 & 8). Tighten screw to increase locking arm friction.
PAGE 4
Figure 5 Figure 6 (Upper/Top Frame) © 2013 Adaptive Technologies Group, Signal Hill, CA 90755 USA (562) 424-1100 Rev.
PAGE 5
Figure 7 (Lower/Bottom Frame) Figure 8 © 2013 Adaptive Technologies Group, Signal Hill, CA 90755 USA (562) 424-1100 Rev.
PAGE 6
4X4-UD55A-VWD 4 Wide x 4 Deep Video Wall Display Installation Guide This display kit mounts Samsung UD55A LCD monitors in a 4 wide by 4 deep landscape configurations. The frame attaches to a wall and receives the LCD monitors by way of four machined fittings (per monitor) that thread into the monitor’s VESA holes. These fittings then insert into the frame’s channels. The monitor’s fittings secure to the frame with locking arms that provide an easy way to remove the monitors for service.
PAGE 7
Step 1: Mount Upper Frame to Wall Scribe a horizontal line on the wall showing the exact location of where the top edge of the upper left monitor will be. Measure down 9.1” (231mm) from that line and scribe another horizontal line showing where the horizontal location of the first adjustable lag bolt will be (Figure 1). Scribe a vertical line showing where the top left side of the upper monitor will be. Measure to the right 16.9” (429.
PAGE 8
Hang the upper frame onto the adjustable lag bolts mounted on the wall. Install hex nut and flat washer then snugly tighten hex nuts. DO NOT TIGTHEN permanently until the entire video frame is installed and adjusted (Figure 3). Step 3: Attach Lower frame to Upper Frame Align vertical joiner brackets from the lower frame to the bottom of the upper frame’s vertical channel holes then secure using the supplied M6 flat head screws (Figure 4). Snugly tighten screws only.
PAGE 9
Step 7: Optional Install Media Player Choose and remove the bottom left or right lower side H-slat by unscrewing its flat head screws (Figure 7). Install the media player to the wall in between the two vertical V-channels using the appropriate fasteners for the media player’s bracket. Re-install the bottom lower side H-slat (Figure 7). Step 8: Install M8 VESA buttons to monitors Thread the M8 adjustable VESA buttons to the VESA mounting holes in the back of each monitor (Figure 8).
PAGE 10
Step 11: Install Second Column Monitors Starting with the top monitor, connect the power and signal wires to each monitor then align its four M8 adjustable VESA buttons with the four large slots in the H-slats. Slide the monitor from right to left until it is snug against the left column monitor (Figure 11). Repeat step 11 for the three lower monitors. Check for front and side alignments-refer to Step 10. Step 13: Install Third Column Monitors Repeat step 11 to install the third column monitors.