Display User's Manual LCGO21EAHBI LCGO21EAHBI-INT INT 21.5” Color LCD Display Model No.
Revision History The revision letter changes with related comments each time the document is updated. Revision Revision Comment 0 Initial Contents 1. Information ................................................................................. 3 2. Equipment Symbols .................................................................... 9 3. Cleaning Instructions ................................................................ 11 4. Disposal of the Unit .......................................................
1. Information Safety Precautions CAUTION Symbol Description Caution!-This This symbol alerts you to important operating considerations or a potential operating condition that could damage equipment. Refer to user's manual or operation's manual for precautionary instructions.
This device complies with part 15 of the FCC rules. Operation is subject to the following two conditions: 1. This device may NOT cause harmful interference, and 2. This device must accept any interference received, including interference that may cause undesired operation. NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC rules.
General recommendations ● Make sure to carefully read the Operating Manual prior to using the monitor in order to properly use the monitor. ● Note that, excluding those cases where a responsibility for legal compensation is recognized, the manufacturer shall bear absolutely no responsibility for damage to this product by a customer or a third party that results from the ignoring of contents entered in this Operating Manual and mistaken use. ● Follow the instructions below for safety use of the LCD Monitor.
Suivez les instructions ci-dessous pour utiliser l'écran LCD en toute sécurité. Pour éviter un choc électrique, ne tentez pas de retirer un couvercle ou de toucher l'intérieur du moniteur. Seul un technicien qualifié peut ouvrir le boîtier du moniteur. N'insérez pas d'objets métalliques ou ne renversez pas de liquide dans le moniteur LCD par les fentes du boîtier. Cela pourrait provoquer un incendie, un choc électrique ou une panne.
L'installateur doit prévoir un système de sauvegarde en cas de chute de la vidéo. Cet équipement ne doit pas être réparé ou entretenu pendant son utilisation avec le patient. ATTENTION : Pour éviter le risque de choc électrique, cet équipement doit être raccordé à un réseau électrique protégé par une mise à la terre. La fiche est utilisée pour la déconnexion du réseau électrique, ne placez pas l'ÉQUIPEMENT ME de telle sorte qu'il soit difficile d'utiliser le dispositif de déconnexion.
Users to be considered A) Installation personnel – only by manufacturer trained and authorized technician B) Maintenance/repair personnel – only by manufacturer trained and authorize technician C) Operating personnel – not in consideration for the graphical images at this stage As there are none to consider, however user interfaces such as OSD and control buttons shall be considered. Installation and OSD adjusting should only be carried by manufacturer trained and authorized personnel.
2. Equipment Symbols Electrical and Electronic Equipment Symbols In addition to the equipment symbols described in your user's manual, the following symbols may be appear on the monitor. Alternating current. Equipotentiality. Connect device to a potential equalization conductor. European Union Declaration of Conformity. FCC. USA only. Complies with applicable US government (Federal Communications Commission) radio radio-frequency frequency interference regulations.
Standby or power indicator. This symbol indicates that the waste of electrical and electronic equipment must not be disposed as unsorted municipal waste and must be collected separately. Please contact an authorized representative of the manufacturer for information concerning the de decommissioning commissioning of your equipment RFID antenna in front design. Indicates the manufacturing date After – sale Service Richardson Electronics GmbH Raiffeisenstr.
3. Cleaning Instructions ● Be sure to unplug the power cord from the mains when cleaning your LCD monitor. ● Take care not to scratch the front surface with any hard or abrasive material. ● Dust, finger marks, grease etc. can be removed with a soft damp cloth (a small amount of mild detergent can be used on the damp cloth). ● Wipe off water drop immediately. ● Using a spray applicator, apply 95% Alcohol and use a soft lint free cloth to clean the screen.
5. Outline Front view Overview 1 2.
Connector view DC 24V IN DC input 9-36V from external adapter VGA DSUB 15 pin connector, Use VGA cable to connect the VGA connector of the monitor and the VGA output connector from source device.(or DVI DVI-I connector from source device via adapter DVI to VGA) DVI DVI 29 pin, single link DVI support. Use DVI cable to connect the DVI connector of the monitor and the DVI output connector from source device.
Connector pin assignments Main board Input signal connectors VGA signal input Pin No. Signal Assignment 1 RED SIGNAL 2 GREEN SIGNAL 3 BLUE SIGNAL 4 GND 5 DET 6 GND GND 7 8 GND 9 DSUB_5V 10 GND 11 GND 12 DDC DATA 13 H.SYNC 14 V.SYNC 15 DDC CLOCK DVI signal input Pin No. Signal Assignment 1 T.M.D.S. Data22 T.M.D.S. Data2+ 3 T.M.D.S. Data2/4 Shield 4 NC 5 NC 6 DDC Clock 7 DDC Data 8 NC 9 T.M.D.S. Data110 T.M.D.S. Data1+ 11 T.M.D.S. Data1/3 Shield 12 NC 13 NC 14 +5V 15 Ground 16 Hot Plug Detect 17 T.M.D.S.
C5 GROUND DP signal input Pin No. Signal Assignment 1 Lane 3 (negative) 2 Ground 3 Lane 3 (positive) 4 Lane 2 (negative) 5 Ground 6 Lane 2 (positive) 7 Lane 1 (negative) 8 Ground 9 Lane 1 (positive) 10 Lane 0 (negative) 11 Ground 12 Lane 0 (positive) 13 GND 14 GND 15 Aux Channel (positive) 16 Ground 17 Aux Channel (negative) 18 Hot Plug Detect 19 DP Power Return 20 +3.
USB HUB & Touch connector USB connector USB B-type 4 Pin (Upstream & Touch) PIN NO. Signal 1 5V 2 D3 D+ 4 GND USB A-type 4 Pin (Downstream) ownstream) PIN NO. Signal 1 5V 2 D3 D+ 4 GND DC 9-36V Power connector 9-36V input Pin No.
6. Operation 5 Key Controls on rear cover : POWER,MENU, ▲ , ▼,ENTER Power: Press this button to turn the monitor on. When the monitor is on, press and hold this buttonfor 3 secondsto turn the monitor off. Menu: Press to open OSD menu. ▲ : Hot Key: Press to increase brightness value. When the menu appeared, press to move the cursor up or to increase item value. ▼ : Hot Key: Press to decrease brightness value. When the menu appeared, press to move the cursor down or to decrease item value.
Clock Phase Back OSD Language English Francais Deutsch Italiano Espanol 日本語 Transparency H.Position V.Position Timeout Back System Reset Back Info./ Exit Resolution :1920x1080 H.Freq :68KHz V.
OSD selection Brightness/Contrast settings VGA 1920x1080@6 0 Hz Brightness/Contrast Brightness 90 Color Mode Contrast 50 Input Source Back Display OSD System Info./Exit Selecting this control allows you to make adjustment to the backlight dimming and contrast of the display screen by the range from 0 to 100. *Press up/down to adjust the brightness any time while the OSD is off Color Mode Settings VGA 1920x1080@6 0 Hz Brightness/Contrast Color Temp.
Color Temp. User VGA 1920x1080@6 0 Hz Brightness/Contrast Color Temp. User Color Mode Red 50 Input Source Green 50 Display Blue 50 OSD Gamma 2.2 System Info./Exit Red You can adjusts the gain of Red by the range from 0 to 100. Green You can adjusts the gain of Green by the range from 0 to 100. Blue You can adjusts the gain of Blue by the range from 0 to 100. Gamma VGA 1920x1080@6 0 Hz Brightness/Contrast Color Temp. 1.8 Color Mode Red 2.0 Input Source Green 2.2 Display Blue 2.
Input Source select VGA 1920x1080@6 0 Hz Brightness/Contrast VGA Color Mode DVI Input Source DisplayPort Display OSD System Info./Exit You can select source from VGA ,DVI and DP. Display settings VGA 1920x1080@6 0 Hz Brightness/Contrast Auto adjust Color Mode H.Position Input Source V.Position Display Clock OSD Phase System Back Info.
Clock Adjust the frequency sampling rate of horizontal pixels for VGA, to equal the video source’s value, thus minimizing artifacts of shimmering vertical lines. Phase Adjust ADC sampling clock phase for VGA, so that the screen image appear crisp and focused. * Display settings are not available for Digital sources. OSD Settings VGA 1920x1080@6 0 Hz Brightness/Contrast Language Color Mode Transparency Input Source H.Position Display English V.Position OSD Timeout System Back Info.
SYSTEM Settings Normal Mode VGA 1920x1080@6 0 Hz Brightness/Contrast Reset Color Mode Back Input Source Display OSD System Info./Exit Reset Select this function to reset all OSD adjustments to the factory default settings Information Normal Mode VGA 1920x1080@6 0 Hz Brightness/Contrast Resolution :1920x1080 Color Mode H.Freq :68KHz Input Source V.Freq : 60Hz Display V Total :1125Lines OSD Color Format : RGB System OP Hours: 0 Hrs Info./Exit This page will show below messages: 1.
7. Display Timing Modes Timing Table Resolution Frequency Input Signal Mode Name H V H(kHz) V(Hz) VGA DVI DisplayPort VGA 640 480 31.47 59.94 O O O 800 600 35.16 56.25 O O O 800 600 37.88 60.32 O O O XGA 1024 768 48.36 60 O O O SXGA 1280 1024 63.98 60.
8. Specifications Product name : 21.5" Color LCD Display Screen technology : TFT active matrix type liquid crystal panel Active screen size : (diagonal) 21.5” Active screen size : 476.64mm (H) x 268.11mm (V) Aspect ratio (H:V) : 16:9 Resolution : 1920 x 1080 Pixel pitch : 0.24825 mm Color support : 16.
External Dimensions 21.
9. Contact Information Legal information and responsibility Richardson Electronics GmbH Boschstr. 8 82178 Puchheim Germany www.canvys.de Technical Support / Service contact Canvys - Visual Technology Solutions A Division of Richardson Electronics Richardson Electronics GmbH Raiffeisenstr. 5 D-78166 Donaueschingen Germany Tel.:+49 (0)771 - 8300-0 Fax:+49 (0)771 - 8300-80 E-Mail: info-europe@canvys.com http://www.canvys.de Please use following link for the registration of service issues: http://www.canvys.
