Installation Guide AMM-1525M/1510M/525M SCSI Audio Host Adapters and Sound Cards R AA AAAA AA AAAAAAAA AAAAAAAA AAAAAAAA AAAAAAAA AAAAAAAA AAAAAAAA AAAAAAAA AAAAAAAA AAAAAAAA AAAAAAAA AAAAAAAA AAAAAAAA AAAAAA AA AA AA AMM-1525M/1510M/525M Installation Guide AA AA AA AA AA AA Part Number: 510659-00, Rev.
1 Getting Started This document provides the basic information needed to quickly configure and install the Adaptec AMM™-1525M, AMM-1510M, and AMM-525M SCSI Audio Host Adapters and Sound Cards. Each adapter provides multimedia capabilities with advanced audio features.
Default Settings The AMM-1525M/1510M/525M is already configured for use with the majority of computers. The default settings are listed below: Description Default Setting Sound Chip Base Address 220h Jumper Block J9 Interrupt Channel (IRQ)1 11 Jumper Block J10 I/O Port Address1 340h Jumper Block J10 IDE Port Address2 Secondary (170h - 177h) Jumper Block J4 IDE Port Enable2 Enabled Jumper Block J4 Host Adapter Termination1 Enabled3 Host Adapter SCSI ID1 7 Configured By — aspi2dos.
IRQ Channel and I/O Port Address (AMM-1525M/1510M Only) Jumper block J10 configures the IRQ channel and I/O port address for SCSI. The default configuration is Extra Jumper I2 I1 I0 I9 PRI Pin Pair Description I2, I1, I0, I9 Determines the host adapter IRQ channel. IRQ 12 = jumper I2 IRQ 11* = jumper I1 IRQ 10 = jumper I0 IRQ 9 = jumper I9 (not recommended with Windows 3.x) PRI Determines I/O port address range.
IDE Port Enable (AMM-1525M/525M Only) Pins 1 and 2 of jumper block J4 enables or disables the IDE port address. The available settings are 1 3 1 2 4 2 Enabled (Default) 3 4 Disabled If you are using the IDE controller on the host adapter, leave this setting enabled. If you are not using the IDE controller on the host adapter, disable this setting.
To connect internal SCSI devices, follow these steps: 1 Attach the connector at one end of the 50-pin SCSI ribbon cable to the AMM-1525M/1510M SCSI connector. Make sure to align pin 1 of the cable with pin 1 of the connectors on the host adapter and internal SCSI device. Note: On ribbon cables, pin 1 is usually marked with a contrasting color on one edge of the cable; a small arrow, a delta symbol (▲), or a “1” usually marks pin 1 on the SCSI connector.
to The aspi2dos ASPI Manager of the Adaptec EZ-SCSI User’s Guide. To change the SCSI ID on your SCSI device, refer to your SCSI device documentation. 6 Connecting IDE Devices (AMM-1525M/525M Only) IDE devices (standard IDE hard disk drives and/or ATAPI CD-ROM drives) are connected to the host adapter by a 40-pin IDE ribbon cable with a 40-pin header connector. The 40-pin IDE ribbon cable included in your kit has connectors at each end.
3 Attach the connector at the other end of the cable to the connector on the first IDE device; maintain pin-1 orientation. 4 To connect a second IDE device, plug the middle connector of the cable to the connector on the second IDE device; maintain pin-1 orientation. Keep these points in mind when installing IDE devices: ■ For each IDE hard disk drive installed in your computer, drive type and parameters must be specified in the computer ’s CMOS setup.
■ For each IDE controller, the first IDE device must be configured as the master device, and the second (if any) as the slave device. See your IDE device documentation for details. 7 Connecting Audio Equipment SPKR Headphones/ Speakers OUT Line Out IN Line In MIC You can connect a variety of audio equipment to the AMM-1525M/1510M/525M, such as a microphone, headphone, powered or nonpowered internal/external speakers, tape deck, CD player, joystick, and MIDI devices, etc.
8 Installing Software Adaptec Installation Manager Adaptec Installation Manager is a software utility that runs and installs the following Adaptec software needed to operate your host adapter (for more information, refer to the Adaptec Installation Manager User’s Guide): ■ ■ ■ ■ ■ DeMucker™–avoids conflicts by disabling references to sound boards currently and previously installed in your computer. (Windows only.) EZ-SCSI™–provides SCSI capabilities by installing SCSI device drivers and other programs.
9 Troubleshooting If you are having problems with your adapter or configuration, make sure the AMM-1525M/1510M/ 525M is firmly seated and secured in the expansion slot, then check the following: Audio ■ To play audio CDs while in Windows, the [MCI] CD Audio driver must be installed. Use the Drivers option in Control Panel to install the driver.
■ For the latest online information about Adaptec products and services, call the Interactive Fax Service 23 hours a day, 7 days a week, at 408-957-7150. The Fax line is out of service 1 hour each day. ■ For technical assistance, call Adaptec’s Technical Support Hot Line at 800-959-SCSI (7274), or 408-945-2550. M–F: 6:00 a.m.– 5:00 p.m., Pacific Time. ■ To order Adaptec software and SCSI cables, call 800-442-SCSI (7274), M–F: 6:00 a.m. to 5:00 p.m., Pacific Time. If you are calling from outside the U.
