Specifications
Table Of Contents
- IBM PC Server and Novell NetWare Integration Guide
- Abstract
- Contents
- Figures
- Tables
- Special Notices
- Preface
- Chapter 1. IBM PC Server Technologies
- Processors
- Clock Rate
- External Interfaces
- Processor Types
- Multiprocessing
- Memory
- Caches
- Memory Interleaving
- Dual Path Buses
- SynchroStream Technology
- Memory Error Detection and Correction
- Standard (Parity) Memory
- Error Correcting Code (ECC)
- Error Correcting Code- Parity Memory (ECC- P)
- ECC on SIMMs (EOS) Memory
- Performance Impact
- Memory Options and Speed
- Bus Architectures
- ISA Bus
- EISA Bus
- Micro Channel Bus
- PCI Bus
- Disk Subsystem
- Hard Disk Interfaces
- SCSI Technology
- SCSI Adapters
- Hard Disk Drives
- RAID Technology
- RAID Classifications
- Recommendations
- LAN Subsystem
- Shared RAM Adapters
- Bus Master Adapters
- PeerMaster Technology
- Security Features
- Tamper- Evident Cover
- Secure I/ O Cables
- Passwords
- Secure Removable Media
- Selectable Drive Startup
- Unattended Start Mode
- Systems Management
- DMI
- SNMP
- NetFinity
- SystemView
- Fault Tolerance
- NetWare SFT III
- Uninterruptible Power Supply (UPS)
- APC PowerChute
- Chapter 2. IBM PC Server Family Overview
- Chapter 3. Hardware Configuration
- The Setup Program
- Main Menu
- Advanced Menu
- Security
- EISA Configuration Utility
- SCSI Select Utility Program
- System Programs
- Starting From the System Partition
- Starting From the Reference Diskette
- Main Menu Options
- Backup/ Restore System Programs Menu
- Set Configuration Menu
- Set Features Menu
- Test the Computer
- More Utilities Menu
- Advanced Diagnostic Program
- RAID Controller Utility
- Drive Information
- Formatting the Disks
- Defining a Hot- Spare Disk
- Creating a Disk Array
- Defining Logical Drives
- Setting the Write Policy
- Initializing the Array
- Backup/ Restoring the Configuration
- Chapter 4. Novell NetWare Installation
- ServerGuide Overview
- Starting ServerGuide
- Installing NetWare 4.1 with ServerGuide
- Installing NetWare 3.12 with Diskettes
- Hardware Requirements
- Software Requirements
- Information Requested at Time of Installation
- Installation Files
- Installation Procedure
- Installing NetWare 4.1 with the Original CD- ROM
- Hardware Requirements
- Software Requirements
- Installation Procedure
- NetFinity Services for NetWare
- System Requirements
- Installing NetFinity Services for NetWare
- The RAID Administration for NetWare Utility
- Installing the Utility
- Hard Disk Failure Simulation
- Simulating with a Hot Spare Drive
- Simulating without a Hot Spare Drive
- Chapter 5. Performance Tuning
- Appendix A. EISA Configuration File
- Appendix B. Hardware Compatibility, Device Driver, and Software Patch Information
- Appendix C. Configuring DOS CD-ROM Support
- List of Abbreviations
- Index
- Special Characters C
- Numerics
- A
- B
- D
- E
- F
- H
- M
- I
- N
- K
- L
- O
- P
- S
- Q
- R
- T
- U
- V
- W
- Z
- ITSO Technical Bulletin Evaluation RED000
If disabled, the system ignores the error and attempts to boot.
3.1.2.2 Advanced Menu - Peripherals
To reach this menu:
•
Press ESC to quit the Boot options.
•
Use the arrows keys to select the integrated peripherals option.
•
Press Enter.
A screen like the one in Figure 26 will appear:
Phoenix BIOS Setup - Copyright 1985-94 Phoenix Technologies Ltd.
Advanced
Integrated Peripherals
Serial Port A: [COM1, 3F8h]
Serial Port B: [COM2, 2F8h]
Parallel Port A: [LPT1, 3F8h, IRQ7]
Parallel Port Mode: [Bi-directional]
Diskette Controller: [Enabled]
Integrated IDE Adapter [Disabled]
Large Disk DOS Compatibility [Disabled]
Memory Gap [Disabled]
Figure 26. PC Server 320 Setup Program - Integrated Peripherals Menu
Serial Port A:
The port can be set to either COM1 or COM3 and uses the IRQ4 if
enabled.
Serial Port B:
The port can be set to either COM2 or COM4 and uses the IRQ3 if
enabled.
Parallel Port:
It can be set to LPT1 or LPT2 and uses the IRQ7.
Diskette Controller:
It uses the IRQ 6 if enabled.
Integrated IDE adapter:
Select:
•
Primary, if IDE devices are present
•
Secondary, if another IDE controller has been added to the system
•
Disabled, otherwise
Note
You must set the W25 jumper on the planar board accordingly.
Large Disk DOS Compatibility:
Select:
•
DOS, if you have DOS
•
Other, if you have another operating system including UNIX or Novell
NetWare
DOS is the default value.
70 NetWare Integration Guide