2410SA Enclosure Kit HIG.
410SA Enclosure Kit HIG.fm Page 1 Thursday, October 23, 2003 1:20 PM In this Guide... Before You Begin 1 Installing the Drive Carriers 2 Labelling the Drive Carriers 3 About the Drive LEDs 3 Installing the Drive Chassis 3 Hot-swapping Disk Drives 6 Technical Specifications 7 This Hardware Installation Guide explains how to set up the 4-bay hot-swappable drive chassis included in the Adaptec® 2410SA Enclosure kit. It also describes how to install and hot-swap hard disk drives.
2410SA Enclosure Kit HIG.fm Page 2 Thursday, October 23, 2003 1:20 PM Installing the Drive Carriers To install a drive carrier: 1 Mount a hard disk drive in a drive carrier and secure it with screws, as shown. 2 Insert the drive carrier into the drive slot and push firmly but gently until you can press the carrier handle down and click the release button into place. Release button 3 Repeat until all four drive carriers are installed.
2410SA Enclosure Kit HIG.fm Page 3 Thursday, October 23, 2003 1:20 PM Labelling the Drive Carriers The four drives are designated slightly differently by the Adaptec 2410SA controller, the drive chassis, and the Adaptec Storage Manager software.
2410SA Enclosure Kit HIG.fm Page 4 Thursday, October 23, 2003 1:20 PM 2 Turn the drive chassis so that you can access the connectors on the rear panel. The connectors are shown in detail in the next Figure. 3 Using the Figure as a guideline, connect the cables. Use gentle but firm pressure to fit the connectors together. ! Caution: The connectors are keyed to fit together one way only. Do not try to force a cable onto a connector. If the cable does not slide on easily, try reversing it.
2410SA Enclosure Kit HIG.fm Page 5 Thursday, October 23, 2003 1:20 PM 4 Install the drive chassis into the computer cabinet, using the screws provided in the Adaptec 2410SA Enclosure kit. (Your computer cabinet may not look exactly the same as the one shown in the example below.) 5 Install the Adaptec Serial ATA RAID 2410SA controller, if you haven’t already. Refer to the printed Adaptec Serial ATA RAID 2410SA Quick Installation Guide, included in the kit, for detailed instructions.
2410SA Enclosure Kit HIG.fm Page 6 Thursday, October 23, 2003 1:20 PM 9 Power on your computer and install the device driver for the Adaptec Serial ATA RAID 2410SA controller, if you haven’t already. Refer to the Adaptec Serial ATA RAID 2410SA Quick Installation Guide, included in the kit, for detailed instructions. Refer to the Adaptec Serial ATA RAID 2410SA Installation and User’s Guide for detailed information about using your Adaptec 2410SA Enclosure Kit.
2410SA Enclosure Kit HIG.fm Page 7 Thursday, October 23, 2003 1:20 PM 3 Mount a new drive in a drive carrier and secure it with screws, as shown in Step 1 on page 2. 4 Insert the drive carrier into the drive slot and push firmly but gently until you can press the carrier handle down and click the release button into place, as shown in Step 2 on page 2. Technical Specifications Occupancy Three 5.
2410SA Enclosure Kit HIG.fm Page 8 Thursday, October 23, 2003 1:20 PM Copyright ©2003 Adaptec, Inc. All rights reserved. No part of this publication may be reproduced, stored in a retrieval system, or transmitted in any form or by any means, electronic, mechanical, photocopying, recording or otherwise, without the prior written consent of Adaptec, Inc., 691 South Milpitas Blvd., Milpitas, CA 95035. Trademarks Adaptec and the Adaptec logo are trademarks of Adaptec, Inc.
2410SA Enclosure Kit HIG.fm Page 9 Thursday, October 23, 2003 1:20 PM Adaptec Customer Support If you have questions about installing or using your Adaptec product, check this document first—you will find answers to most of your questions here. If you need further assistance, use the support options listed below. Technical Support Identification (TSID) Number ■ Before contacting Technical Support, you need your unique 12-digit TSID number. The TSID number identifies your product and support status.
2410SA Enclosure Kit HIG.fm Page 10 Thursday, October 23, 2003 1:20 PM Europe ■ Visit our Web site at www.adaptec-europe.com. ■ German: To speak with a Technical Support Specialist, call +49 89 43 66 55 22, Monday to Friday, 9:00 to 17:00, CET. For support via e-mail, submit your question to Adaptec’s Technical Support Specialists at ask-de.adaptec.com. ■ French: To speak with a Technical Support Specialist, call +49 89 43 66 55 33, Monday to Friday, 9:00 to 17:00, CET.
2410SA Enclosure Kit HIG.fm Page 11 Thursday, October 23, 2003 1:20 PM Limited 3-Year Hardware Warranty 1. Adaptec, Inc. (“Adaptec”) warrants to the purchaser of this product that it will be free from defects in material and workmanship for a period of three (3) years from the date of purchase.
2410SA Enclosure Kit HIG.fm Page 12 Thursday, October 23, 2003 1:20 PM Regulatory Compliance Statements Federal Communications Commission Radio Frequency Interference Statement WARNING: Changes or modifications to this unit not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment. This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC rules.
2410SA Enclosure Kit HIG.fm Page 13 Thursday, October 23, 2003 1:20 PM R Adaptec, Inc. 691 South Milpitas Boulevard Milpitas, CA 95035 USA ©2003 Adaptec, Inc. All rights reserved. Adaptec and the Adaptec logo are trademarks of Adaptec, Inc. which may be registered in some jurisdictions. Part Number: 513760-03, Rev.
