User`s guide
Table Of Contents
- About This Guide
- Kit Contents and System Requirements
- About Your RAID Controller
- Standard RAID Controller Features
- Adding Enhanced Features
- Adding a Battery Backup Module
- Upgrading the Controller Firmware
- About the Adaptec 3085
- About the Adaptec 3405
- About the Adaptec 3805
- About the Adaptec 31205
- About the Adaptec 31605
- About the Adaptec 4000
- About the Adaptec 4800SAS
- About the Adaptec 4805SAS
- About the Adaptec 2420SA
- About the Adaptec 2820SA
- About the Adaptec 2130SLP
- About the Adaptec 2230SLP
- Getting Started
- Installing the Controller and Disk Drives
- Creating a Bootable Array
- Installing the Driver and an Operating System
- Installing the Driver on an Existing Operating System
- Managing Your Storage Space
- Solving Problems
- Introduction to Serial Attached SCSI
- Understanding RAID
- Using the Adaptec RAID Configuration Utility
- Using the Array Configuration Utility for DOS
- Using the Adaptec Flash Utility
- Adaptec Serial Controller LED and I2C Connector Reference
- Adaptec 2420SA Activity LED and I2C Connector Specification
- Adaptec 2820SA Activity LED and I2C Connector Specification
- Adaptec 3085 LED and I2C Connector Specification
- Adaptec 3405 LED and I2C Connector Specification
- Adaptec 3805 LED and I2C Connector Specification
- Adaptec 31205 LED and I2C Connector Specification
- Adaptec 31605 LED and I2C Connector Specification
- Adaptec 4800SAS LED and I2C Connector Specification
- Adaptec 4805SAS LED and I2C Connector Specification
- Safety Information
- Technical Specifications
- Index
Appendix A: Introduction to Serial Attached SCSI ● 73
Some backplanes support daisy-chain expansion to other backplanes. For example, you can
daisy-chain (connect one to the next) up to nine Adaptec S50 enclosures to a single SAS card in
a host system.
SAS Expander Connections
A SAS expander device literally expands the number of end devices that you can connect
together. Expander devices, typically embedded into a system backplane (see page 72), support
large configurations of SAS end devices, including SAS cards and SAS and SATA disk drives.
With expander devices, you can build large and complex storage topologies.
There are two types of SAS expanders: fanout expanders and edge expanders. Each performs a
different role in a storage system. (For more information about how SAS expanders work, refer
to the STA Web site at www.scsita.org.)
You can connect up to 128 SAS ports to an edge expander. (A single edge expander can
therefore support up to 128 SAS addresses.)
You can connect up to 128 edge expanders to a fanout expander.
You can use only one fanout expander in any single SAS domain (a topology of SAS—and
possibly SATA—end devices and expander devices). A single SAS domain can therefore
comprise up to 16,384 SAS ports (and therefore up to 16,384 SAS addresses including the
fanout expander).
The next figure illustrates (in very basic terms) a SAS domain and shows how SAS cards, SAS
and SATA disk drives, and expander devices can fit together in a large data storage topology.
SAS Card
SAS Card
Disk Drives
Disk Drives
Disk Drives
Disk Drives
Disk Drives
Disk Drives
Fanout Expander
Disk Drives
Edge
Expander
Edge
Expander
S ATA
S ATA
S ATA
S ATA
SAS
SAS
SAS
S ATA
Edge
Expander
S ATA
S ATA
SAS
SAS
Edge
Expander
Edge
Expander
SAS Card
SAS DomainSAS Domain
S ATA SAS