Installation Instructions

ManualsBrandsAdams Rite ManualsAccess Control Power productsPower Supply for Exit Devices

1 of 8

PS-Exit Exit Device

Power Supply

Overview

The Adams Rite PS-EXIT power supply provides power and control for up to two MLR

or LR exit devices. Each exit device is controlled by a timer that is initiated by a switch

closure. The timer is user-conﬁgured and holds the exit device(s) in the unlatched

position for 2 – 60 seconds. At the end of the selected time, the exit device(s) will

re-latch. If the switch controlling the exit device is closed longer than the selected

time, the exit device remains unlatched until the controlling switch is released.

• An optional mode is available that allows both retraction timers

to activate in response to a closure of either switch.

• The PS-EXIT is listed as an Exit Device, Access Control System Unit to UL294

requirements for power supplies and Canadian Standards CAN/CSA - C22.2.

• Exit devices under access system control remain latched during a

complete power failure but always allow free mechanical egress.

Summary of content (8 pages)

PAGE 1
PS-Exit Exit Device Power Supply Installation Instructions Overview The Adams Rite PS-EXIT power supply provides power and control for up to two MLR or LR exit devices. Each exit device is controlled by a timer that is initiated by a switch closure. The timer is user-configured and holds the exit device(s) in the unlatched position for 2 – 60 seconds. At the end of the selected time, the exit device(s) will re-latch.
PAGE 2
Specifications PART NUMBERS & LOCATIONS CIRCUIT BOARD PART NUMBER LOCATION PS-EXIT Battery Backup System Kit 31-0725 BBK-EXIT Power Supply Power Supply PS-EXIT VOLTAGE MEASUREMENTS • OUT1/OUT2 when IN1/IN2 is OPEN: less than 1.6 VDC • OUT1/OUT2 when IN1/IN2 is CLOSED: 24 – 26 VDC • OUT1/OUT2 are rated at a maximum output current of 400 mA each.
PAGE 3
Connector & Signal Descriptions CONNECTOR PIN DESCRIPTION 1 2 3 1&2 3&4 5 6 7 8 9 & 10 L N 24-V (+) from battery charging system during AC fail J1 24VDC supplied to battery charging system Battery Backup 24-V return Input #2, normally-open activation switch input Input #1, normally-open activation switch input Exit Device #2 return J3 Exit Device #2, +24 VDC when activated Field Wiring Exit Device #1 return Exit Device #1, +24 VDC when activated Fire alarm interface, normally-closed (no alarm) input Mai
PAGE 4
Configure the PS-EXIT CAUTION Damage to the PS-EXIT or to exit devices may occur if connections are not made in accordance with the following procedure, or if connections are bypassed or omitted. NOTE: PS-EXIT is rated for 115 VAC only. Switch 2 (SW2) is factory preset for 115 VAC operation. 1 ENSURE that PS-EXIT is set to 115 VAC as shown in Diagram 1.
PAGE 5
Connect the Fire Alarm Interface NOTES: If used with fire doors, PS-EXIT is required to be under the control of an automatic fire alarm control system. PS-EXIT is factory preset to be used without a fire alarm interface. 1 ENSURE that the installed jumper is in place at Positions 9 and 10 (FIRE) of Terminal Block J3 to use PS-EXIT without a fire alarm interface.
PAGE 6
Mount the PS-EXIT power supply 1 MOUNT the PS-EXIT power supply close to the exit device (door) to be operated. For UL 294 compliance, PS-EXIT must be installed in a controlled/protected area. NOTES: Mounting holes are 1/4" in diameter. Enclosure dimensions are 10" x 10" x 4". 2 FASTEN the PS-EXIT power supply securely to the wall using the mounting holes located on the back of the enclosure.
PAGE 7
Wire the Automatic Door Interface (Optional) NOTE: This step is required to use PS-EXIT with an automatic door opener. Automatic door-opening systems need an indication of the latched state. The latch controller, located in the panic bar device, has relay contacts that signal the latched state to the automatic door opener. The relay contacts are closed when the latch is fully retracted and are open when the latch is extended. 1 CONNECT the automatic door opener as indicated in Diagram 6.
PAGE 8
Troubleshooting Guide The exit device doesn’t unlock when connected to the access control system. No power to the exit device Neither exit device retracts after the control switch is activated Main Power LED (Red) is not lit FIRE LED on PS-EXIT Board is not lit IN1/IN2 LEDs do not light in response to input switches 1. ENSURE that the MAIN POWER and FIRE LEDs are on. If not, check AC power and the fire alarm interface or fire alarm jumper.