Specification Sheet

Request to Exit –
Monitor/Signal Switch
For all Adams Rite Exit Devices
M1 – Single Switch
M2 – Dual Switch
Mounted in the exit device pushbar on the
hinge end, the switch can be used to activate signal light, horn, monitor,
or other devices. Switch can be wired for normally open or normally
closed. Can be retrofit in field to existing exit devices. Dual switch version
offers redundancy as required by some building codes or it can operate
a second signaling device.
Order REX-Monitor/Signal Kits for upgrading any 3000 or 8000 Series
device: 91-0897-01 for Single Switch or 91-0897-02 for Dual Switch.
Cylinder Dogging
For all non-fire rated Adams Rite Exit Devices
For management control of dogging. Any standard 15/16" to 1-1/8"
long Mortise cylinder with MS
®
cam can be used in a pushbar
prepared at factory with Cylinder Dogging kit. Not for use with Alarm,
ED, EL, LR or SE options.
Electric Dogging
For all Adams Rite Exit Devices
The ED option uses a holding magnet that keeps the pushbar
depressed (set manually) and the latch retracted for a lower profile
exit device, resulting in less damage and quieter operation. An internal
microswitch signals when the bar is depressed – ideal for automatic
door operators. On fire-rated devices, it must be wired through the fire
alarm system. Devices operate at 24 VDC at 0.6 Amps, with only a
transformer and rectifier.
Not to be used as an access control element. SE Motorized Latch
Retraction option or LR Latch Retraction option is recommended with
access control devices such as card readers or keypads.
Matching End Caps
Standard Adams Rite exit devices come with black metal end caps. Matching
end caps are available for applications where it is preferable that the end
caps match the finish of the exit device. Available for US finishes only.
Specify by adding “MEC” after the regular ordering matrix.
Monitored Dummy Pushbar
8099M1 – Single Switch
8099M2 – Dual Switch
8099-00 – Dummy Only
Dummy pushbar with no latch mechanism but with either a single or
dual monitor/signal switch. May be used with a maglock, where bar turns
off magnet and allows exit from building. Dual switch version allows
redundancy where required by code or the operation of a signal device.
Specify door type and width when ordering. (How to order below)
TRIM
3080 Series Entry Trim
The Grade 1 3080 Series Entry Trim provides outside activation for
doors with any type of Adams Rite deadlatch or exit device. The locked
handle is protected from vandalism and forced entry with a breakaway
clutching mechanism.
3090 Keyless Entry
A battery-operated keyless entry control device, the eForce-150 3090
Keyless Entry provides access control for Adams Rite deadlocks,
deadlatches, and exit devices for aluminum stile, steel, and
wood door applications.
The eForce 3090P (Prox) and 3090C (iCLASS) Keyless Entries provide
maximum security with either HID® Prox or iCLASS contactless card reader.
HOW TO ORDER 8099 DUMMY PUSHBAR Specify quantity and the following information. Order related products separately.
PRODUCT NO. MONITOR DOOR TYPE PUSHBAR FINISH WIDTH US FINISH
8099 -M1 -3 0 36 -US32
00 Inactive Dummy Bar 3 Aluminum 0 US Finish 30 30 inches US3 Bright Brass
M0 Active Dummy Bar, no monitoring switches 4 Wood or hollow metal 1 Clear Anodized 628 36 36 inches US4 Satin Brass
M1 Active Dummy Bar, one monitoring switch 2 Dark Bronze Anodized 313 40 40 inches US32 Bright Stainless
M2 Active Dummy Bar, two monitoring switches 3 Black Anodized 335 48 48 inches US32D Satin Stainless
OPTIONS & ACCESSORIES FOR EXIT DEVICES
ED-20
EXIT DEVICES
©2014, Hanchett Entry Systems, Inc., an ASSA ABLOY Group company.