Specification Sheet

ManualsBrandsAdams Rite ManualsFaucet HandlesAdams Rite 4590-04-00-628 Paddle Handle - 802081

Dual Force

2290

Interconnected

Deadbolt/Deadlatch

Operation

Key or thumbturn retracts or extends deadbolt or deadlatch.

Inside lever retracts both when conﬁgured with interconnect

feature. Outside lever retracts latch only. Latch holdback

feature activated or deactivated by turning key to retract latch

and sliding holdback button on faceplate down to hold and up

to release.

Speciﬁcations

INTER-CONNECTION

• Field selectable inter-connection feature allows interior trim

to retract deadbolt and deadlatch. Consult the local building

ofﬁcial for guidance in code compliance. 1-3/4" minimum door

thickness required.

CYLINDER BASKET

• 1-1/8" or 1-1/2" only.

LATCHBOLT/DEADBOLT

• Latchbolt: 5/8" throw of solid brass. Easily reversible using

only a screwdriver. Deadbolt: 1" throw of stainless steel.

AUXILIARY DEADLATCH PIN

• Stainless steel. Deadlocks latchbolt to prevent “loiding”

or case-knife entry.

FACEPLATES

• Measures 1-1/4" x 8". Includes FaceStyle faceplate system

that adapts to ﬂat or beveled door edge.

STRIKES

• Standard strike furnished is the 2206 (ASA) strike for ﬂat

jamb where door closes ﬂush or nearly ﬂush.

HOLLOW

METAL

WOOD

STILE OR RAIL

ELECTRIFIED

OPTION

GRADE 1

E82102

The Dual Force 2290 Interconnected Deadbolt/Deadlatch

provides access control and security for wood or hollow

metal doors. Latch and deadbolt capabilities are combined

for fast, easy, and panic-proof exiting.

Function

The Dual Force 2290 combines the access control capabilities of a latch with

the security of a deadbolt. The key retracts and extends the deadbolt (and

deadlatch) from either side. The exterior lever retracts the latch only while the

inside lever retracts the deadbolt and latch simultaneously for fast, easy, panic-

proof exiting. Intended for out-swinging doors.

CYLINDER CAM

• The Dual Force 2290 is operable by any standard 1-5/32"

diameter mortise cylinder with MS

cam dimensioned as

shown. Cylinders with MS

cams can be readily obtained from

most cylinder manufacturers. See CYLINDERS section for

cylinder make, thumbturn and trim ring information.

OPTIONS

• Specify trim option, lever style, ﬁnish, and strike. Also adapts

to paddle operator 4591. See 2190 for aluminum door version

for narrow stile door construction. Thick Door Kit 2190-TDK-

XX available separately. Specify door thickness. Request to

Exit RXK-4600 switch available for small format levers. Note

that the low proﬁle trim (trim option 3) is recommended for in-

swing door applications.

ELECTRIFIED TRIM OPTIONS

• Order 2190 Electriﬁcation Kit EK-2190 for adding to the

clutched exterior lever. Dual voltage 12/24 VDC rated for

continuous duty operation. Energizing the lever allows exterior

lever to be turned to retract latch only. The electriﬁed option is

not available for low proﬁle trim (trim option 3).

STANDARD PACKAGE

• Individually boxed with trim as speciﬁed, strike and machine

screws for mounting. Cylinders available separately.

Shipping weight: 2 lbs.

HOW TO ORDER DUAL FORCE

2290 INTERCONNECTED DEADBOLT/DEADLATCH

Specify quantity and the following information. Order related products separately.

PRODUCT

NO.

BACKSET STRIKE FACEPL ATE FINISH TRIM

HANDLE

DESIGNATION

TRIM AND HANDLE

FINISH

2290 -3 1 1 1 01 -32D

3 1-1/8" 0 None 0 US to match trim ﬁnish 0 None 00 No Handle 03 Bright Brass (US3)

4 1-1/2" 1 Standard Flat 1 Clear Anodized 628 1 With Trim Set STANDARD SERIES: 04 Satin Brass (US4)

2 Dark Bronze Anodized 313 2 With Electriﬁed Trim Set 01 Curve 10B Dark Bronze (US10B)

3 Black Anodized 335 3 Low Proﬁle Trim 02 Round 32 Bright Stainless (US32)

03 Square 32D Satin Stainless (US32D)

DESIGNER SERIES:

MD MJ

ME MN (Handed)

MG MV (Handed)

MI MW

Trim options 1 and 2 are for outswing doors only.

LOCK CASE

CAM

DOOR CENTERLINE

*TOLERANCE: ± 1/16

DOOR STILE

TRIM RING

CYLINDER

TR* = A + .125

– B

TR* = A + .132

– B

FOR MS

LOCKS: FOR 4500 SERIES LATCHES:

“Dim A”

1830

2190

2290

MS1837

MS1850S

MS1850SN

MS1861

MS1950

1875

1890

4300

4510

4530

4900

4781

4920AN

8300

8400

8650

DEADLOCK

DEADLATCH

SERIES

EXIT

DEVICES

1870

1870HM

1877

3080

3090

FLUSHBOLTS

TRIM

THIS CAM AVAILABLE FROM:

ADAMS RITE

ARROW

ASSA

BEST

CORBIN RUSSWIN

DORMA

FALCON

KABA-ILCO

MEDECO

SARGENT

SCHLAGE

WEISER

YALE

.120"

3.0mm

.182"

4.6mm

.334"

8.5mm

.620"

15.7mm

.721"

18.3mm

.950"

24.1mm

.334"

8.5mm

.800" ± .005"

20.3mm ± .127mm

.850" ± .005"

21.6mm ± .127mm

THIS CAM AVAILABLE

FROM ABOVE CYLINDER

MANUFACTURERS

ON SPECIAL ORDER

(OR MAKE FROM

STANDARD CAM)

THIS CAM AVAILABLE

FROM ALL CYLINDER

MANUFACTURERS

(STANDARD CAM)

Narrow stile doors require a trim ring to ﬁll the gap remaining between the cylinder

shoulder and stile when a standard mortise cylinder is used. If the security of the

hardened steel Adams Rite MS4043 Cylinder Guard is not required, this ring may be

simply a length of 1.171 I.D. tubing. Its length varies depending on door thickness or

cylinder make and number of pins. The speciﬁc length required can be quickly

determined by the following formula:

DIMENSIONS OF CAM TO OPERATE:

DIMENSIONS OF CAM

TO OPERATE:

4070 SERIES DEADBOLT

DIMENSIONS OF CAM

TO OPERATE:

2331 DEADBOLT

CYLINDER TRIM RING FOR NARROW STILES

“

” is trim ring length.

“

” is cylinder height (less shoulder but including cam).

“

” is one-half of door thickness.

STANDARD SERIES:

01-CURVE

MD MI

02-ROUND

ME MJ

03-SQUARE

MG MN

DESIGNER SERIES:

INCHES

Nominal, subject to tolerance ext remes.

Jamb

Preparation

2206 Strike

Stile Preparation

For Clutched Exterior

Trim Set

Latch/Lock,

Cylinder

& Lever

Installation

CUTOUT

TOLERANCE:

+ 0.015 +0.38

- 0.000 - 0.0

MAXIMUM GAP

DOOR TO JAMB:

1/8"

Cylinder Cam

2290 Series locks are operable by any

standard 1-5/32" diameter mortise cylinder

with special MS

cam dimensioned as shown.

Cylinders with MS

cams can be readily

obtained from most cylinder manufacturers.

See page SW-37 for cylinder make and trim

information.

BEVELED OR FLAT EDGE

CAM TOLERANCE:

CYLINDER

25/32

3/161/8R

1-1/4

4-3/16

2-1/8

1-1/4

BACKSET

ARMO RED

FACE PLATE

1-1/4 X 8"

FLAT

(INCLUDED) FP K-0066-0X-XXX

HOW BACKSET

IS MEAS UR ED

CYLINDER

FLAT

BEVEL

4 7/8

3 3/8

4 1/8

1 1/4

1/8

5/8

LOCK

OF LOCK AND STRIKE

STRIKE PLATE

5-25/32

"A"

"B"

3/4

1-11/32

11/16

2-5/32

2-27/32

7-11/16

5/8

3-3/16

1-23/32

1/2

BACKSE T"A" "B"

1- 1/8" 1- 1/8

1-3/4

1- 1/2"

1- 1/22-1 /8

CLUTCHED EXTERIOR

TRIM SET

SMALL FORMAT

LEVER SET