Specification Sheet

Dimensions
3080-01*
3080E-01*
3080-MD
3080E-MD
3080-MI
3080E-MI
3080-ME
3080E-ME
3080-02*
3080E-02*
3080-03*
3080E-03*
3080-MV**
3080E-MV**
3080-MG
3080E-MG
3080-MW
3080E-MW
3080-MJ
3080E-MJ
3080-MN**
3080E-MN**
1-29/32"
48.4mm
3-1/4"
82.6mm
5"
127mm
1-29/32"
48.4mm
1-29/32"
48.4mm
2-29/32"
73.8mm
4-11/32"
110.3mm
1-29/32"
48.4mm
1-29/32"
48.4mm
3-11/16"
93.7mm
3-19/32"
91.3mm
5-1/8"
130.2mm
4-5/16"
109.5mm
1-29/32"
48.4mm
3-5/16"
84.1mm
4-29/32"
124.6
mm
1-29/32"
48.4mm
3-23/32"
94.5mm
5"
127
mm
1-29/32"
48.4mm
3-5/8"
92.1mm
4-3/8"
111.1mm
1-29/32"
48.4mm
3-1/4"
82.6mm
4-3/16"
106.4mm
1-29/32"
48.4mm
3-5/8"
92.1mm
4-1/2"
114.3mm
1-29/32"
48.4mm
4"
101.6mm
4-11/16"
119.1mm
8-3/32"
205.6mm
8-3/32"
205.6mm
8-3/32"
205.6mm
8-3/32"
205.6mm
8-3/32"
205.6mm
8-3/32"
205.6mm
8-3/32"
205.6mm
8-3/32"
205.6mm
8-3/32"
205.6mm
8-3/32"
205.6mm
3-15/32"
88.1mm
4-9/16"
115.9mm
8-3/32"
205.6mm
CYLINDER
ESCUTCHEON
SPACER
CYLINDER
RETAINER RING
SOLENOID
ASSEMBLY*
FLAT HEAD
SCREWS (2 PLCS)*
#6-32 X 1/4"
ROTATION
LIMITING
PINS
* ELECTRIFIED TRIM ONLY
CYLINDER
ESCUTCHEON
SPACER
CYLINDER
RETAINER RING
SOLENOID
ASSEMBLY*
FLAT HEAD
SCREWS (2 PLCS)*
#6-32 X 1/4"
ROTATION
LIMITING
PINS
* ELECTRIFIED TRIM ONLY
Door Preparation & Trim Installation
Door prep and installation will differ depending on the type of exit device being used. Refer to the Adams
Rite templates for 3080 Entry Trim or 3080E Electrified Entry Trim for preparation details.
MORTISE CYLINDER – 4036-01
• Standard diameter five-pin unit with MS cam, suitable
for use with entry trim. Available in quantity all keyed
different (KD), in pairs (KA2), or 50 alike (KA50). Any
other make standard mortise cylinder with MS
®
cam
can be used to key-in with existing systems.
B
LOCK CASE
CAM
TR
A
DOOR CENTERLINE
*TOLERANCE: ± 1/16
DOOR STILE
TRIM RING
CYLINDER
TR* = A + .125 – B TR* = A + .132 – B
FOR MS
®
LOCKS: FOR 4500 SERIES LATCHES:
“Dim A”
R
R
1830
2190
2290
MS1837
MS1850S
MS1850SN
MS1861
MS1950
1875
MS
+
1890
4300
4510
4530
4900
4781
4920AN
8300
8400
8650
DEADLOCK
DEADLATCH
SERIES
SERIES
EXIT
DEVICES
1870
1870HM
1877
3080
3090
FLUSHBOLTS
TRIM
THIS CAM AVAILABLE FROM:
ADAMS RITE
ARROW
ASSA
BEST
CORBIN RUSSWIN
DORMA
FALCON
KABA-ILCO
MEDECO
SARGENT
SCHLAGE
WEISER
YALE
.120"
3.0mm
.182"
4.6mm
.334"
8.5mm
.620"
15.7mm
R
.721"
18.3mm
.950"
24.1mm
.334"
8.5
mm
.800" ± .005"
20.3mm ± .127mm
.850" ± .005"
21.6mm ± .127mm
THIS CAM AVAILABLE
FROM ABOVE CYLINDER
MANUFACTURERS
ON SPECIAL ORDER
(OR MAKE FROM
STANDARD CAM)
THIS CAM AVAILABLE
FROM ALL CYLINDER
MANUFACTURERS
(STANDARD CAM)
Narrow stile doors require a trim ring to fill the gap remaining between the cylinder
shoulder and stile when a standard mortise cylinder is used. If the security of the
hardened steel Adams Rite MS4043 Cylinder Guard is not required, this ring may be
simply a length of 1.171 I.D. tubing. Its length varies depending on door thickness or
cylinder make and number of pins. The specific length required can be quickly
determined by the following formula:
DIMENSIONS OF CAM TO OPERATE:
DIMENSIONS OF CAM
TO OPERATE:
4070 SERIES DEADBOLT
DIMENSIONS OF CAM
TO OPERATE:
2331 DEADBOLT
CYLINDER TRIM RING FOR NARROW STILES
“ TR ” is trim ring length.
“
A ” is cylinder height (less shoulder but including cam).
“
B ” is one-half of door thickness.
CYLINDER CAM
• 3080 Series Entry Trim can accept
any standard 1-5/32" diameter mortise
cylinder with MS
®
cam dimensioned as
shown. Cylinders with MS
®
cams can
be readily obtained from most cylinder
manufacturers. See CYLINDERS for
cylinder make, thumbturn and trim
ring information.
* The 3080-01, -02, and -03 lever handles are designed to return within 1/2" of the door face. Handles in the Designer Series do
not have this same feature. Please verify with local code requirements to ensure compliance.
** Handed
T-4
TRIM
3080 SERIES ENTRY TRIM
©2014, Hanchett Entry Systems, Inc., an ASSA ABLOY Group company.
All measurements are approximate and are provided for informational purposes only. Refer to the product Installation Instructions.