TABLE OF CONTENTS 1 Flushbolts & Pivots Table of Contents SECTION & PAGE NUMBER PRODUCT Deadlocks 1870 Cylinder-Operated Flushbolt FP-1 – FP-2 1870HM Cylinder-Operated Flushbolt FP-3 – FP-4 1877 Cylinder-Operated Flushbolt FP-5 – FP-6 MS1880, MS1881 Two-Point Flushbolts FP-7 – FP-8 MS2180 Auto-Release Two-Point Flushbolt FP-9 – FP-10 B1921, B1923 Reinforcing Pivots FP-11 – FP-12 Options & Accessories for Flushbolts FP-13 – FP-14 SECTION & PAGE NUMBER PRODUCT RITE Touch® Digital Glass
TABLE OF CONTENTS 2 Electric Strikes Accessories SECTION & PAGE NUMBER PRODUCT PRODUCT SECTION & PAGE NUMBER 7100, 7101 Electric Strikes ES-1 – ES-2 4000 Series MS® Deadlock Strikes A-1 – A-2 7110, 7111 Electric Strikes ES-3 – ES-4 4015 Threshold Bolt A-3 – A-4 7130, 7131 Electric Strikes ES-5 – ES-6 4016 Header Bolt A-5 – A-6 7140 Electric Strike ES-7 – ES-8 4085 Header Bolt (Pairs of Doors Only) A-7 – A-8 7160 Electric Strike ES-9 – ES-10 4089 Exit Indicator A-9 – A-10 7170 Elec
RITE TOUCH® RT1050D DIGITAL GLASS DOOR LOCK DEADLOCKS RITE Touch® RT1050D Digital Glass Door Lock DL-1 Features • Battery-operated lock uses 4 AA alkaline batteries • Expected battery life is 1 year based on 10 daily uses • Operating temperature 5°F to 130°F (-15°C to 55°C) • Programming via touch-screen • RITE Touch will support up to 40 credential cards (extra cards available seperately) Operation FULL GLASS ELECTRIFIED PRODUCT The surface-mounted RITE Touch RT1050D provides flexible, keyless acces
DEADLOCKS RITE TOUCH® RT1050D DIGITAL GLASS DOOR LOCK DL-2 All measurements are approximate and are provided for informational purposes only. Refer to the product Installation Instructions. Dimensions 31/64" 9/16" 14.3mm LOCKBODY 12.3mm 1-59/64" 48.8mm 2-55/64" 72.6mm 5/32" 4mm 3-1/16" 1/16" 77.8mm 1.6mm 7-21/64" 7-1/2" 186.1mm 190.5mm 31/64" 9/16" 14.3mm STRIKE PLATE 3/16" 4.8mm 12.3mm 1-1/2" 38.1mm 1-51/64" 1-39/64" 45.6mm 40.9mm 7-21/64" 186.1mm HOW TO ORDER 3/32" 2.
DEADLOCKS 1830 Bottom Rail Deadlock (Swing Bolt) DL-3 1830 BOTTOM RAIL DEADLOCK (SWING BOLT) Operation 360° turn of key or thumbturn throws or retracts the counterbalanced bolt. Key can be removed only when bolt is in a positively locked or unlocked position. Lock accepts any standard 1-5/32" mortise cylinder from either or both sides. Cylinder must have MS® dimensioned cam. Specifications CYLINDER HEIGHT (BACKSET) • 31/32" and 1-1/8" only.
DL-4 DEADLOCKS 1830 BOTTOM RAIL DEADLOCK (SWING BOLT) All measurements are approximate and are provided for informational purposes only. Refer to the product Installation Instructions. Dimensions Stile & Threshold Preparation 6-3/8" 161.9mm CYLINDER 1-11/32" 5-31/32" 34.1mm 151.6mm 3/8" 9.5mm 1/4" 6.4mm 6-3/8" 161.9mm “A” 21/32" 16.7mm THRESHOLD 2-5/16" 58.7mm 29/64" 1" 11.5mm 25.4mm 6-7/8" 1/2" 2-3/16" 174.6mm 55.6mm 12.7mm 1-3/4" 44.5mm 1-1/4" DIA. 31.
DEADLOCKS MS1837 Series MS® Two-Point Deadlock DL-5 MS1837 SERIES MS® TWO-POINT DEADLOCK Operation 360° turn of key or thumbturn throws counterbalanced bolt into opposite door and drops bolt into threshold. Key can be removed only when bolts are in a positively locked or unlocked position. Lock accepts any standard 1-5/32" diameter mortise cylinder from either or both sides. Cylinder must have MS® dimensioned cam. Specifications CYLINDER BACKSET • 1-1/2" only.
DL-6 DEADLOCKS MS1837 SERIES MS® TWO-POINT DEADLOCK All measurements are approximate and are provided for informational purposes only. Refer to the product Installation Instructions. Dimensions Installation INSTALL ADAPTOR ARM IN LOCK FROM REAR WITH BOLT RETRACTED AS SHOWN. FACEPLATE 1-1/4" 2-1/4" 31.8mm LOCK MOUNTING PLATE 25mm 38.1mm 1" 25.4mm DRIVE PIN THROUGH SLOTS IN LOCK SIDE PLATES, PASSING THROUGH HOLE IN THE ADAPTOR ARM. 57.2mm 1-1/2" BACKSET 63/64" 7/8" 22.2mm 1/8" 3.
DEADLOCKS MS1847 SERIES MS® DEADLOCK/DEADLATCH MS1847 Series MS® Deadlock/Deadlatch DL-7 Operation Can be operated by a standard cylinder, so the glass door may be keyed-in with other types of doors. Three hub slot positions allow installation even where jamb and stile design provides severely limited turn clearance. Specifications LATCH VERSION FULL GLASS ALUMINUM • The same stainless steel hookbolt, but spring-loaded for automatic latching, is provided by the MS1847-11 and MS1847-13.
DL-8 DEADLOCKS MS1847 SERIES MS® DEADLOCK/DEADLATCH All measurements are approximate and are provided for informational purposes only. Refer to the product Installation Instructions. Dimensions Stile Preparation 1-1/8" 28.6mm 3/32" 13.5mm 2.4mm 3-11/16" ADJUSTMENT FULL RADIUS TYP. NOTE: DIMENSIONS SHOWN ARE RECOMMENDED MINIMUM 3-7/32" 81.8mm 9.5mm MAX. 4mm 5.2mm SEE DASH NUMBER FOR SQUARE OR RADIUS ENDS 3/8" 5/32" 13/64" DRILL AND CSK FOR #6 SCREW (2 PLCS) 17/32" 93.7mm 1" 25.
DEADLOCKS MS1850S Series MS® Deadlock DL-9 MS1850S SERIES MS® DEADLOCK Specifications CYLINDER BACKSET • 7/8", 31/32", 1-1/8", or 1-1/2" only. CASE • Steel with corrosion-resistant plating, measures 1" x 6" x depth. Depth varies by backset (see table on back of page). BOLT • 5/8" x 1-3/8" x 2-7/8" with 1-3/8" throw. Eight-ply laminated stainless steel. Center ply has alumina-ceramic core to defeat any hacksaw attack, including rod-type “super” hacksaws.
DL-10 DEADLOCKS MS1850S SERIES MS® DEADLOCK All measurements are approximate and are provided for informational purposes only. Refer to the product Installation Instructions. Dimensions Stile Preparation HOW BACKSET IS MEASURED: 53/64" 29/64" STILE CYLINDER C L 1" 11.5mm 25.4mm 21mm 1-19/32" C L SHOWN WITH FLAT FACEPLATE “A” 40.5mm BACKSET FLAT 6-57/64" 175mm BACKSET MEASURED AT CENTERLINE OF STILE NOSE 29/64" 11.5mm 1-1/4" DIA. HOLE C L 31.8mm RADIUS 5/32" R 4mm (4 PLCS.
DEADLOCKS MS1850S-050 Series MS® Deadlock DL-11 MS1850S-050 SERIES MS® DEADLOCK Specifications CYLINDER BACKSET • 7/8", 31/32", 1-1/8", or 1-1/2" only. CASE • Steel with corrosion-resistant plating, measures 1" x 6" x depth. Depth varies by backset (see table on back of page). BOLT ALUMINUM • 5/8" x 1-3/8" with 13/16" throw. Eight-ply laminated stainless steel.
DL-12 DEADLOCKS MS1850S-050 SERIES MS® DEADLOCK All measurements are approximate and are provided for informational purposes only. Refer to the product Installation Instructions. Dimensions Stile Preparation HOW BACKSET IS MEASURED: 25.4mm 15.9mm 21mm STILE CYLINDER C L 1" 5/8" 53/64" C L SHOWN WITH FLAT FACEPLATE “A” 6mm 40.5mm BACKSET 1-27/32" C L BACKSET MEASURED AT CENTERLINE OF STILE NOSE 27/64" 15/64" 10.7mm 1-19/32" FLAT LOCKFACE 46.8mm 6-57/64" 175mm RADIUS 1-1/4" 31.
DEADLOCKS MS1850SN MS® Series Deadlock (ANSI Size) DL-13 MS1850SN MS® SERIES DEADLOCK (ANSI SIZE) Operation 360° turn of key or thumbturn throws or retracts the counterbalanced bolt. Key can be removed only when bolt is in a positively locked or unlocked position. Lock accepts any standard 1-5/32" diameter mortise cylinder from either or both sides. Cylinder must have MS® dimensioned cam. Specifications CYLINDER BACKSET • 1-1/2" only.
DL-14 DEADLOCKS MS1850SN MS® SERIES DEADLOCK (ANSI SIZE) All measurements are approximate and are provided for informational purposes only. Refer to the product Installation Instructions. Dimensions Jamb & Stile Preparation FOR 4003-01 ANSI STRIKE STILE 1/4" 6.4mm 53/64" 1-1/4" 19/32" 21mm 56.4mm 54.4mm C L 8-1/64" 4-7/8" 123.8mm 11/32" 8.7mm 38.9mm 1-1/4" 31.8mm DIA. 203.
DEADLOCKS MS1850SN-050 MS® Deadlock (ANSI Size) DL-15 MS1850SN-050 MS® DEADLOCK (ANSI SIZE) Operation 360° turn of key or thumbturn throws or retracts the counterbalanced bolt. Key can be removed only when bolt is in a positively locked or unlocked position. Lock accepts any standard 1-5/32" diameter mortise cylinder or thumbturn from either or both sides. Cylinder must have MS® dimensioned cam. Specifications CYLINDER BACKSET • 1-1/2" only.
DL-16 DEADLOCKS MS1850SN-050 MS® DEADLOCK (ANSI SIZE) All measurements are approximate and are provided for informational purposes only. Refer to the product Installation Instructions. Dimensions Stile & Wood Door Preparation 1/4" 2-7/32" 56.4mm 6.4mm STILE 19/32" 53/64" 15.1mm 21mm HOW BACKSET IS MEASURED: 1-1/4" 31.8mm CYLINDER C L SHOWN WITH FLAT FACEPLATE 1-15/32" 1" 25.4mm 2-9/64" 54.4mm 2-9/32" 57.9mm C L 37.3mm 1-1/4" DIA. FLAT 31/32" 11/32" 24.6mm 8.7mm 31.
DEADLOCKS MS1861 Series Bottom Rail Deadbolt DL-17 MS1861 SERIES BOTTOM RAIL DEADBOLT Operation 360° turn of key or thumbturn throws or retracts bolt(s). Key can be removed only when bolts are in a positively locked or unlocked position. Lock accepts any standard 1-5/32" diameter mortise cylinder from either or both sides. Cylinder must have MS® dimensioned cam. Specifications CYLINDER BACKSET FULL GLASS • Minimum backset is approximately 2-1/4" for the MS186101 with vertical bolt only.
DL-18 DEADLOCKS MS1861 SERIES BOTTOM RAIL DEADBOLT All measurements are approximate and are provided for informational purposes only. Refer to the product Installation Instructions. Dimensions Rail Preparation #8-32 DRILL & TAP TYP. BOTTOM RAIL MTG. WEB FOR MS1861-02 5-49/64" 3/4" 146.4mm BACKSET 1" 19.1mm 25.4mm 7/16" 11.1mm DIA. THROW 1-1/8" 3-5/8" 21.6mm 92.1mm 14.3mm 5-25/64" 4" 9/16" 1/4" 14.3mm 6.4mm 1" 25.4mm 2" 1-55/64" 136.9mm 101.6mm 1-1/4" DIA. 31.
DEADLOCKS DL-19 1875 TWO-POINT DEADLOCK 1875 Two-Point Deadlock Operation 90° rotation of turn throws or retracts bolts. 360° turn of key deadlocks mechanism, preventing operation of the turn in either locked or unlocked position. Specifications CYLINDER BACKSET • Bolt arms require inside stile clearance of 1-11/16" on one side of cylinder center, 1" on the other. CASE • Steel with corrosion-resistant plate, measures 1" x 6" x 2-5/8".
DL-20 DEADLOCKS 1875 TWO-POINT DEADLOCK All measurements are approximate and are provided for informational purposes only. Refer to the product Installation Instructions. Dimensions 7-15/16" 201.6mm 11/32" 7-1/4" 8.7mm 1-1/64" 25.8mm 184.2mm 6" 152.4mm 1/4-20 NC (2 PLCS) 1-21/32" 1" 2-5/8" 1-23/32" 42.1mm 66.8mm MAX. 43.7mm 25.4mm 3-1/2" 1-1/32" 8-63/64" 26.2mm 88.9mm 1-63/64" 228.2mm TRAVEL 50.4mm 25.4mm 26.
DEADLOCKS DL-21 MS+1890 SERIES MS® DEADLOCK/DEADLATCH MS+1890 Series MS® Deadlock/Deadlatch Specifications CYLINDER BACKSET • 31/32", 1-1/8", or 1-1/2". CASE • Steel with corrosion-resistant plating, measures 1" x 7-3/8" x depth. Depth varies by backset (see table on back of page). LATCHBOLT • Zinc alloy with Delrin face for smooth, quiet action, measures 5/8" x 5/8" with 7/16" throw. Handing easily reversible.
DL-22 DEADLOCKS MS+1890 SERIES MS® DEADLOCK/DEADLATCH All measurements are approximate and are provided for informational purposes only. Refer to the product Installation Instructions. Dimensions “A” Jamb Preparation HOW BACKSET IS MEASURED: 25mm 21mm 39/64" 3/16" 31.8mm 11/16" 1-19/32" 17/32" 40.5mm 1/4" FLAT 6.4mm 7/32" 13.5mm 1/4" 1-1/4" DIA. BACKSET 17.5mm 51/64" 4.8mm Cutout same as MS1850 Deadbolt plus holes for handle mount. CYLINDER 4mm (4 PLCS) C L 15.5mm 20.
DEADLOCKS MS1950 Series Deadlock DL-23 MS1950 SERIES DEADLOCK Specifications CYLINDER BACKSET • 31/32", 1-1/8", or 1-1/2" only. CASE • Fully stainless steel case and internal components, measures 1" x 6" x depth. Depth varies by backset (see table on back of page). BOLT • 5/8" x 1-3/8" x 2-7/8" with 1-3/8" throw. Eight-ply laminated stainless steel. Center ply has alumina-ceramic core to defeat any hacksaw attack, including rod-type “super” hacksaws.
DL-24 DEADLOCKS MS1950 SERIES DEADLOCK All measurements are approximate and are provided for informational purposes only. Refer to the product Installation Instructions. Dimensions Stile Preparation HOW BACKSET IS MEASURED: STILE CYLINDER C L 5/8" 7/8" 1-19/32" C L 1" 40.5mm BACKSET 15.9mm 25.4mm 22.2mm FLAT 6-57/64" SHOWN WITH FLAT FACEPLATE “A” 175mm 1-1/4" 31.8mm DIA. HOLE C L BACKSET MEASURED AT CENTERLINE OF STILE NOSE 11/32" 8.7mm RADIUS 5/32" R 4mm C L (4 PLCS.
DEADLOCKS MS1950-050 Series Deadlock DL-25 MS1950-050 SERIES DEADLOCK Specifications CYLINDER BACKSET • 31/32", 1-1/8", or 1-1/2" only. CASE • Fully stainless steel case and internal components, measures 1" x 6" x depth. Depth varies by backset (see table on back of page). BOLT ALUMINUM • 5/8" x 1-3/8" with 13/16" throw. Eight-ply laminated stainless steel.
DL-26 DEADLOCKS MS1950-050 SERIES DEADLOCK All measurements are approximate and are provided for informational purposes only. Refer to the product Installation Instructions. Dimensions Stile Preparation HOW BACKSET IS MEASURED: STILE CYLINDER C L C L 1" 5/8" 7/8" 15.9mm 25.4mm 22.2mm 1-19/32" 40.5mm BACKSET FLAT SHOWN WITH FLAT FACEPLATE “A” 6-57/64" 175mm C L BACKSET MEASURED AT CENTERLINE OF STILE NOSE 7/32" 1-1/4" 31.8mm DIA. HOLE RADIUS 5.6mm 5/32" R C L 4mm (4 PLCS.
DUAL FORCE® 2190 INTERCONNECTED DEADBOLT/DEADLATCH DEADLOCKS Operation Dual Force® 2190 Interconnected Deadbolt/Deadlatch STRIKES OPTIONS Key or thumbturn retracts or extends deadbolt or deadlatch. Inside lever retracts both when configured with interconnect feature. Outside lever retracts latch only. Latch holdback feature activated or deactivated by turning key to retract latch and sliding holdback button on faceplate down to hold and up to release.
DUAL FORCE® 2190 INTERCONNECTED DEADBOLT/DEADLATCH DL-28 DEADLOCKS All measurements are approximate and are provided for informational purposes only. Refer to the product Installation Instructions. Dimensions Stile Preparation FOR CLUTCHED EXTERIOR TRIM SET HOW BACKSET IS MEASURED: 1" 63/64" 25.4mm 25mm BACKSET CYLINDER C L Dimensions 25mm 29mm 68.3mm 1-1/4" 31.8mm DIA. 63/64" 1-9/64" 2-11/16" 63/64" 2-11/16" 2-15/32" 25mm 68.3mm 62.7mm 1-23/64" 34.5mm 1-19/32" 40.
DUAL FORCE® 2290 INTERCONNECTED DEADBOLT/DEADLATCH DEADLOCKS Dual Force® 2290 Interconnected Deadbolt/Deadlatch DUAL FORCE® 2290 INTERCONNECTED DEADBOLT/DEADLATCH DL-29 Operation CYLINDER CAM Key or thumbturn retracts or extends deadbolt or deadlatch. Inside lever retracts both when configured with interconnect feature. Outside lever retracts latch only.
DUAL FORCE® 2290 INTERCONNECTED DEADBOLT/DEADLATCH DL-30 DEADLOCKS All measurements are approximate and are provided for informational purposes only. Refer to the product Installation Instructions. Dimensions Stile Preparation FOR CLUTCHED EXTERIOR TRIM SET 1/2" 63/64" 25mm 29mm 68.3mm 1-1/4" 63/64" 1-9/64" 2-11/16" 2-11/16" 68.3mm 31.8mm 12.7mm 25mm Dimensions 63/64" BACKSET “B” 1-23/64" 2-15/32" 34.5mm 25mm 62.7mm 2-5/32" 54.8mm “A” 1" 2-5/32" 25.4mm 8-59/64" 4-13/64" 54.
DEADLOCKS Specifications 2331 Heavy Duty Deadbolt BACKSET • 1-3/4" only. CASE • Zinc alloy, measures 7/8" x 3-5/8" x 2-5/8" deep. DIMENSIONS OF CAM TO OPERATE: DEADLOCK SERIES HOLLOW METAL WOOD DL-31 2331 HEAVY DUTY DEADBOLT GRADE 1 E16121 DEADLATCH SERIES “Dim A” .800" ± .005" 20.3mm ± .127mm EXIT The 2331 Heavy Duty Deadbolt provides a heavy duty DEVICES .120"R deadbolt lock that 3.0mm expands into .182"the strike for heavy duty 4.6mm FLUSHBOLTS wood or hollow metal applications.
DL-32 DEADLOCKS 2331 HEAVY DUTY DEADBOLT All measurements are approximate and are provided for informational purposes only. Refer to the product Installation Instructions. Dimensions Wood Door Preparation 3/16" 4.8mm 7/8" 1" 22.2mm 25.4mm PILOT FOR #8 WOOD SCREW (6 PLCS)* 5/32" 4mm R TYP. 1-3/64" 26.6mm 3-11/16" NOTE: DIM’S SHOWN 93.7mm 2-21/32" 2-9/16" 67.5mm 65.1mm 1-3/4" ARE RECOMMENDED MINIMUM. 44.5mm 3/16" 4.8mm 4-13/16" 122.2mm 3/4" 1-1/4" DIA. 31.8mm (THRU HOLE) 19.
DEADLOCKS 4070 Series Short Throw Deadbolt (Projection Style) 4070 SERIES SHORT THROW DEADBOLT (PROJECTION STYLE) DL-33 Operation 180° turn of key or thumbturn projects or retracts the bolt. Accepts any standard 1-5/32" mortise cylinder from either or both sides. Cylinder must have special cam to fit (as shown). DIMENSIONS OF CAM TO OPERATE: Specifications DEADLOCK SERIES CYLINDER BACKSET • 7/8", 31/32", or 1-1/8" only. CASE • Steel with corrosion-resistant plating. 1" x 6" x depth.
DEADLOCKS 4070 SERIES SHORT THROW DEADBOLT (PROJECTION STYLE) DL-34 All measurements are approximate and are provided for informational purposes only. Refer to the product Installation Instructions. Dimensions Stile Preparation STILE HOW BACKSET IS MEASURED: “A” CYLINDER C L 27/32" 1-7/8" 1" 21.4mm 47.6mm 25.4mm 5/8" FLAT 15.9mm BACKSET MEASURED AT CENTERLINE OF STILE NOSE BACKSET C L 1-1/4" 31.8mm DIA. 5-41/64" 143.3mm 7/32" 5/8" C L 5.6mm 15.9mm RADIUS 5-5/8" C L 142.
4189, 4190 FLUSH LOCKSETS (INCLUDING DEADLOCK) DEADLOCKS DL-35 Operation 4189, 4190 Flush Locksets (Including Deadlock) Both locksets operated from inside by a simple up or down movement of a slide button, set flush in the deeply recessed finger pull. The lock mechanism (latching action unavailable) is the time-tested and field-proven Adams Rite MS1847 and features the adjustable, self-protecting bolt. Matching “dummy set” is also available (4195).
DEADLOCKS 4189, 4190 FLUSH LOCKSETS (INCLUDING DEADLOCK) DL-36 All measurements are approximate and are provided for informational purposes only. Refer to the product Installation Instructions. Dimensions Stile Preparation 1-1/4" DRILL AND CSK FOR #6 SCREW (2 PLCS) 28.2mm 1-1/4" 31.8mm 17/32" 1-7/64" 31.8mm 1-5/16" 1-5/64" 13.5mm 27.4mm 33.3mm 1-49/64" 44.8mm 4189-09 ROUND CUTOUT 4190-09 4189-10 SQUARE CUTOUT 4190-10 LOCATION OF CYLINDER ON 4190 LOCKSET ONLY 3-7/32" 81.
4430, 4431 FLUSH LOCKSETS (INCLUDING DEADLOCK) DEADLOCKS 4430, 4431 Flush Locksets (Including Deadlock) DL-37 Operation Both locksets operated from inside by a simple up or down movement of a slide button, set flush in the deeply recessed finger pull. The lock mechanism (latching action unavailable) is the time-tested and field-proven Adams Rite MS1848 and features the adjustable, self-protecting bolt. Matching “dummy set” is also available (4432).
DEADLOCKS 4430, 4431 FLUSH LOCKSETS (INCLUDING DEADLOCK) DL-38 All measurements are approximate and are provided for informational purposes only. Refer to the product Installation Instructions. Dimensions Stile Preparation 1-1/4" 1-1/4" 31.8mm 17/32" DRILL AND CSK FOR #6 SCREW (2 PLCS) 31.8mm Installation 1-5/64" 13.5mm 27.4mm 3-7/32" 81.8mm 3-11/16" 8-29/32" 93.7mm 226.2mm 1-29/64" 36.9mm 15/64" 6mm 8-21/32" 219.9mm LOCATION OF CYLINDER ON 4431 LOCKSET ONLY 1/8" 3.
DEADLOCKS 5017 WOOD DOOR DEADLOCK/DEADLATCH 5017 Wood Door Deadlock/Deadlatch DL-39 Operation 45° rotation of turn or key throws or retracts bolt. Bolt is selfprotecting: if door is shut while bolt is extended, it will retract, preventing damage or accidental lock-out. Specifications BACKSET • 1-3/16" (1-1/4" including faceplate). CASE WOOD • Stainless steel, measures 1/2" x 4" x 1-19/32" deep. Bolt is laminated stainless steel (specify 5015 for zinc plated steel case and faceplate).
DL-40 DEADLOCKS 5017 WOOD DOOR DEADLOCK/DEADLATCH All measurements are approximate and are provided for informational purposes only. Refer to the product Installation Instructions. Stile Preparation Dimensions FOR LOCK, TURN & CYLINDER PULL 1-9/16" MIN 1/16" 39.7mm 1.6mm 1/2" 5/8" 12.7mm 1-1/32 15.9mm 1/8" R 3.2mm (4 PLCS) 51/64 26.2mm 20.2mm 7/32" 5.6mm DIA. (2 PLCS) 7/32" 1-19/32 5.6mm 40.5mm 11/16" 1-1/4" 17.45mm FULL RADIUS BOTH ENDS 31.8mm 1/8" 2-9/16" 3.18mm 65.
DEADLOCKS CYLINDERS Options & Accessories for Deadlocks CYLINDER PULLS The 4024, 4025, 4026 Cylinder Pulls are designed to operate Adams Rite MS1847 Deadlocks and 5017 Wood Door Deadlock. 4036 MORTISE CYLINDER The 4036 Mortise Cylinder is a standard 1" long, 1-5/32" diameter cylinder that provides five-pin security with most Adams Rite locks or latches.
DL-42 OPTIONS & ACCESSORIES FOR DEADLOCKS DEADLOCKS TRIM 1000 TURNS The 1000 Turns with or without escutcheon are designed to operate Adams Rite MS1847 Deadlocks and 5017 Wood Door Deadlock. These turns mount easily to door pull or other trim plate using push-nut mounting. The 1004 Turn has a longer, more ergonomically-friendly turn lever, the 1015 Turn is available for wood door applications with the 5017 Wood Door Deadlock.
STEEL HAWK 4300 ELECTRIFIED DEADLATCH (ELATCH) DEADLATCHES Steel Hawk 4300 Electrified Deadlatch (eLatch) STEEL HAWK 4300 ELECTRIFIED DEADLATCH (ELATCH) DA-1 Operation CYLINDER CAM Turn key, apply voltage, or operate handle or paddle to release the spring-loaded latchbolt. Electrically-rated for continuous duty for timed applications. Interface with access control. Uses any standard mortise cylinder with MS® cam.
DA-2 STEEL HAWK 4300 ELECTRIFIED DEADLATCH (ELATCH) DEADLATCHES All measurements are approximate and are provided for informational purposes only. Refer to the product Installation Instructions. Dimensions Stile Preparation “B” Latch, Paddle & Cylinder Installation “A” 63/64" 5/8" 25mm 15.9mm 1" 25.4mm ADJUSTABLE MOUNTING TUBE BRACKET MAY BE REMOVED FOR MOUNTING ON BRIDGES, TABS, OR EITHER METHODS. HOW BACKSET IS MEASURED: CYLINDER C L 1-19/32" 40.5mm 1-7/16" 36.5mm C L 2-49/64" 70.
DEADLATCHES 4510 Standard Duty Deadlatch DA-3 4510 STANDARD DUTY DEADLATCH Specifications BOLT HOLDBACK • While bolt is held fully retracted, a reverse turn of the key retains the bolt, allowing the door to be free swinging. CYLINDER BACKSET • 7/8", 31/32", 1-1/8" or 1-1/2" only. CASE • Measures 1" x 5-13/16" x depth. Depth varies by backset (see table on back of page). Steel with corrosion-resistant plating. ALUMINUM GRADE 1 E8231 LATCHBOLT • 1/2" x 1" x 1/2" throw.
DA-4 DEADLATCHES 4510 STANDARD DUTY DEADLATCH All measurements are approximate and are provided for informational purposes only. Refer to the product Installation Instructions. Dimensions “A” Stile Preparation Identical to MS 1850A Series (See also prep for 4590 Paddle) 17/32" 13.5mm HOW BACKSET IS MEASURED: 1" 57/64" BACKSET CYLINDER C L 25.4mm 22.6mm STILE CL C L 1-19/32" BACKSET MEASURED AT CENTERLINE OF STILE NOSE 1/2" 40.5mm FLAT 7/32" 5.6mm 12.7mm C L 6-57/64" 1-1/4" DIA.
DEADLATCHES DA-5 4530 STANDARD DUTY DEADLATCH 4530 Standard Duty Deadlatch Specifications BOLT HOLDBACK • While bolt is held fully retracted, a reverse turn of the key retains the bolt, allowing the door to be free swinging. CYLINDER BACKSET • 7/8", 31/32", or 1-1/8" only. CASE • Measures 1" x 5-13/16" x depth. Depth varies by backset (see table on back of page). Steel with corrosion-resistant plating.
DA-6 DEADLATCHES 4530 STANDARD DUTY DEADLATCH All measurements are approximate and are provided for informational purposes only. Refer to the product Installation Instructions. Dimensions Stile & Jamb Preparation 17/32" “A” 13.5mm 7/8" To replace 4070 lock, old 4050 latch, 970 lock or 1450 latch of same backset: 31.8mm FLAT BACKSET MEASURED AT CENTERLINE OF STILE NOSE 51/64" 20.2mm 5.6mm NO PREPARATION REQUIRED CYLINDER 1-1/4" 22.
DEADLATCHES 4781 TWO-POINT DEADLATCH WITH PADDLE 4781 Two-Point Deadlatch with Paddle DA-7 Inside Operation Push paddle to unblock top bolt and withdraw bottom bolt. Continuing to push will open the door in a very natural, ergonomically-friendly motion. Paddle stroke is approximately 1-1/2" at extreme end. Rod adjustment allows paddle (centerline) to be mounted at any height from 30 to 44 inches above the finished floor.
DA-8 DEADLATCHES 4781 TWO-POINT DEADLATCH WITH PADDLE All measurements are approximate and are provided for informational purposes only. Refer to the product Installation Instructions. Dimensions Door Preparation 3/4" 1-1/4" X 1-1/4" 31.8mm 19.1mm 31.8mm MIN I.D. INTERIOR SIDE OF HEADER DIA. 1-3/64" 26.6mm UP TO 66" 1676.4mm 6.4mm BACKSET 1" 1/4" 25.4mm 6.4mm ESCUTCHEON 5/8" DOORS WITH OTHER THICKNESS OR WALL WILL REQUIRE MODIFICATION TO THE DEVICE. 1" 15.9mm 25.4mm 3/8" 9.
DEADLATCHES DA-9 4900 HEAVY DUTY DEADLATCH 4900 Heavy Duty Deadlatch Specifications BOLT HOLDBACK • While bolt is held fully retracted, a reverse turn of the key retains the bolt, allowing the door to be free swinging. CYLINDER BACKSET • 31/32", 1-1/8", or 1-1/2". CASE ALUMINUM • Measures 7/8" x 5-13/16" x depth. Depth varies by backset (see table on back of page). Steel with corrosion-resistant plating. Screw-fastened tube spacer brackets allow for cleaner removal when tab mounting.
DA-10 DEADLATCHES 4900 HEAVY DUTY DEADLATCH All measurements are approximate and are provided for informational purposes only. Refer to the product Installation Instructions. Dimensions Stile Preparation Identical to MS1850A or MS1850S Series (See also prep for 4591 paddle). HOW BACKSET IS MEASURED: “A” STILE BACKSET CYLINDER 5/8" 15.9mm 1" 29/32" 25.4mm 23mm 1-19/32" 40.5mm FLAT BACKSET MEASURED AT CENTERLINE OF STILE NOSE 1/2" 1/4" 6-57/64" 6.4mm 12.7mm 1-1/4" DIA. 175mm 31.
DEADLATCHES 4920AN Heavy Duty Deadlatch (ANSI Size) DA-11 4920AN HEAVY DUTY DEADLATCH (ANSI SIZE) Operation Turn key or operate handle to retract spring-loaded Latchbolt. To hold bolt retracted, push it in and secure by reverse turn of key. Uses any standard mortise cylinder with MS® dimensioned cam. Specifications BOLT HOLDBACK • While bolt is held fully retracted, a reverse turn of the key retains the bolt, allowing the door to be free swinging.
DA-12 DEADLATCHES 4920AN HEAVY DUTY DEADLATCH (ANSI SIZE) All measurements are approximate and are provided for informational purposes only. Refer to the product Installation Instructions. Dimensions Jamb & Door Preparation Nominal, subject to tolerance extremes Identical to MS1850SN Series (See also prep for 4591 paddle). HOW BACKSET IS MEASURED: CYLINDER STRIKE C L 5/8" “A” 15.9mm LATCH C L BACKSET C L 29/32" 1-3/16" 1-1/4" 23mm 30.2mm FLAT 31.
DEADLATCHES Options & Accessories for Deadlatches OPTIONS & ACCESSORIES FOR DEADLATCHES DA-13 POWER 4603 RECTIFIER Converts low voltage AC current to DC of same voltage. Installs in low voltage line between transformer and strike. Full wave bridge type. Rated 2 Amps. (200 PIV). 4605 TRANSFORMER Converts 120VAC to 12VAC/24VAC. Rated 40 Volt-amp output assures plenty of power for strike release.
FLUSHBOLTS & PIVOTS 1870 CylinderOperated Flushbolt FP-1 1870 CYLINDER-OPERATED FLUSHBOLT Operation 360° turn of key throws or retracts the hex-section bolt. Key can be removed only when bolt is in a positively locked or unlocked position. Accepts any standard 1-5/32" mortise cylinder from either or both sides. Cylinder must have MS® dimensioned cam (see CYLINDERS). Specifications CYLINDER BACKSET • 31/32" or 1-1/8" only.
FP-2 FLUSHBOLTS & PIVOTS 1870 CYLINDER-OPERATED FLUSHBOLT All measurements are approximate and are provided for informational purposes only. Refer to the product Installation Instructions. Dimensions Stile Preparation “A” HOW BACKSET IS MEASURED: 7/8" 1" 22.2mm 25.4mm 1-1/64" 25.8mm For installation locking threshold. Invert for header locking. 1-19/32" CYLINDER 40.5mm BACKSET MEASURED AT CENTERLINE OF STILE NOSE 6-57/64" 175mm 1-1/4" 31.8mm FLAT 1-11/32" DIA. 34.1mm 12" 304.
FLUSHBOLTS & PIVOTS 1870HM CylinderOperated Flushbolt FP-3 1870HM CYLINDER-OPERATED FLUSHBOLT Operation 360° turn of key throws or retracts the hex-section bolt. Key can be removed only when bolt is in a positively locked or unlocked position. Accepts any standard 1-5/32" mortise cylinder from either or both sides. Cylinder must have MS® dimensioned cam (see CYLINDERS). Specifications CYLINDER BACKSET • 1-1/4" only.
FP-4 FLUSHBOLTS & PIVOTS 1870HM CYLINDER-OPERATED FLUSHBOLT All measurements are approximate and are provided for informational purposes only. Refer to the product Installation Instructions. Dimensions 1-1/4" Door Preparation 31.8mm BACKSET For installation locking threshold. Invert for header locking. 1-29/32" HOW BACKSET IS MEASURED: 48.4mm 1-1/4" 31.8mm 2-1/8" 54mm CYLINDER 1-1/4" 31.8mm 8-1/64" 203.6mm 1-1/4" 31.8mm 7-1/4" DIA. 184.2mm FLAT 8" 203.
FLUSHBOLTS & PIVOTS 1877 CylinderOperated Flushbolt FP-5 1877 CYLINDER-OPERATED FLUSHBOLT Operation 360° turn of key throws or retracts the hex-section bolt. Key can be removed only when bolt is in a positively locked or unlocked position. Accepts any standard 1-5/32" mortise cylinder from either or both sides. Cylinder must have MS® dimensioned cam (see CYLINDERS). Specifications CYLINDER BACKSET • 1-1/4" only. CYLINDER HEIGHT WOOD • Standard length (cylinder center to door edge) is 13-1/2".
FP-6 FLUSHBOLTS & PIVOTS 1877 CYLINDER-OPERATED FLUSHBOLT All measurements are approximate and are provided for informational purposes only. Refer to the product Installation Instructions. Dimensions Installation For installation locking threshold. Invert for header locking. 1-29/32" 48.4mm 1-1/4" 31.8mm 1" 25.4mm #12 X 1-1/4˝ FLAT HARD WOOD SCREW 1-1/4" 31.8mm FACEPLATE 1/4" 6.4mm 7/8" 22.2mm 1/8" 3.2mm 1" 25.4mm 1/8" 3.2mm BACKSET LOCK MTG PLATE 1-1/4" 31.8mm 2-1/8" 54mm DIA. 1-1/4" 31.
FLUSHBOLTS & PIVOTS MS1880, MS1881 Two-Point Flushbolts MS1880, MS1881 TWO-POINT FLUSHBOLTS FP-7 Operation Turn knob or lever 180° clockwise to throw hardened steel bolts into header and threshold and clear strike opening so pivoted MS® bolt can enter from active door. Counterclockwise turn retracts vertical bolts and blocks entry of pivoted bolt. Operates in conjunction with any MS® pivoting deadlock. Specifications TURN HEIGHT • Matches cylinder height of MS® lock in active door.
FP-8 FLUSHBOLTS & PIVOTS MS1880, MS1881 TWO-POINT FLUSHBOLTS All measurements are approximate and are provided for informational purposes only. Refer to the product Installation Instructions. Dimensions Stile Preparation 23/32" 18.3mm THROW 15/16" 23.8mm 9/64" 3/4" 3.6mm DIA. MS1880 19.1mm 3/4" 19.1mm DIA. TOP GUIDE BRACKET FACE OF STILE MS1881 1-1/16" 27mm CYLINDER 7/8" ON ACTIVE DOOR LEAF 22.2mm 8-1/8" 206.4mm 15/16" 23.
FLUSHBOLTS & PIVOTS MS2180 Auto-Release Two-Point Flushbolt MS2180 AUTO-RELEASE TWO-POINT FLUSHBOLT FP-9 Operation Turn knob or lever 120° counterclockwise to throw stainless steel bolts into header and threshold and clear strike opening so pivoted MS® bolt can enter from active door. Clockwise turn retracts vertical bolts and blocks entry of pivoted bolt. Operates in conjunction with any MS® pivoting deadlock.
FP-10 FLUSHBOLTS & PIVOTS MS2180 AUTO-RELEASE TWO-POINT FLUSHBOLT All measurements are approximate and are provided for informational purposes only. Refer to the product Installation Instructions. Dimensions Stile Preparation 7/8" 22.2mm 57/64" 23/32" 22.6mm 18.3mm THROW CL 3/4" 19.1mm TOP GUIDE BRACKET DRILL & CSK FOR #6-32 FLAT HEAD SCREW (3 PLCS) FACE OF STILE 3/4" 19.1mm 57/64" 22.6mm 2-11/16" 68.3mm 27/32" 21.4mm OF CYLINDER ON ACTIVE DOOR LEAF 39/64" 15.
FLUSHBOLTS & PIVOTS B1921, B1923 Reinforcing Pivots B1921, B1923 REINFORCING PIVOTS FP-11 Specifications TYPE • Full surface reinforcing pivots for flush doors. FINISH • Zinc plating over steel. MATERIAL • Heavy-duty 3/16" cold-rolled steel. CYCLE TESTING • 1,500,000 repetitions WOOD HOLLOW METAL CAPACITY • Supports weights up to 300 lbs. The B1921 and B1923 Reinforcing Pivots provide an economical way to transfer load from hinges of sagging doors. HOLE PATTERN • Symmetrically located.
FP-12 FLUSHBOLTS & PIVOTS B1921, B1923 REINFORCING PIVOTS All measurements are approximate and are provided for informational purposes only. Refer to the product Installation Instructions. Dimensions Installation 1/8" B1921 3.2mm side view 1/8" 3.2mm MIN. CLEAR B1921/B1923 Pivot Assembly FRAME PIVOT RIGHT HAND PIVOT BUSHING 1/2" LEFT HAND PIVOT BUSHING 12.7mm MATCHES 4" HINGE BARREL CENTERLINE PIVOT BOLT & LOCK WASHER DOOR PIVOT 1/8" 3.2mm B1923 side view 1/8" 3.2mm MIN.
FLUSHBOLTS & PIVOTS OPTIONS & ACCESSORIES FOR FLUSHBOLTS FP-13 Options & Accessories for Flushbolts Adams Rite Flushbolts can be ordered with a variety of related products including strike plates, trim and cylinder accessories and compatible products such as Adams Rite deadlocks. Please see product pages for more information on all available flushbolt types, functions, installation requirements and complete How-to-Order guides.
3100 SERIES (FIRE-RATED) 8100 SERIES (LIFE-SAFETY) SURFACE VERTICAL ROD EXIT DEVICE EXIT DEVICES 3100 Series (Fire-Rated) 8100 Series (Life-Safety) Surface Vertical Rod Exit Device ED-1 Features PROJECTION • Patented top latching mechanism interlocks door to frame • Strong, durable construction for a high level of security • Adjustable steel rods protected in contoured covers • Easy to install WOOD ELECTRIFIED OPTION FIRE RATED 3100 SERIES ONLY • Pushbar clad or anodized, not plated, in a variety
ED-2 3100 SERIES (FIRE-RATED) 8100 SERIES (LIFE-SAFETY) SURFACE VERTICAL ROD EXIT DEVICE Options and Accessories SILENT ELECTRIFICATION MOTORIZED LATCH RETRACTION EXIT DEVICES HOW TO ORDER • The SE Motorized Latch Retraction option provides near-silent operation for quiet environments such as hospitals, offices, hotels, and libraries where solenoid-driven devices would be disruptive.
8200 SERIES (LIFE-SAFETY) NARROW STILE SURFACE VERTICAL ROD EXIT DEVICE EXIT DEVICES 8200 Series (Life-Safety) Narrow Stile Surface Vertical Rod Exit Device ED-3 Specifications 8200 SERIES CERTIFICATIONS: • UL 305 Panic Hardware • Warnock/Hersey Life-Safety Listing • ANSI/BHMA A156.3 Grade 1 • California State Fire Marshall • New York City MEA* *Consult Factory for specific number MATERIALS • Pushbar made of extruded aluminum, clad or anodized in a variety of finishes.
8200 SERIES (LIFE-SAFETY) NARROW STILE SURFACE VERTICAL ROD EXIT DEVICE ED-4 EXIT DEVICES Bolts and Strikes REQUEST TO EXIT (REX) – MONITOR / SIGNAL SWITCH • Mounted in the exit device pushbar on the hinge end, the switch can be used to activate signal light, horn, monitor, or other devices. • The patented top latching mechanism utilizes a rotating top bolt which deadlatches around the header strike, interlocking the door to the frame. Supplied with standard header strike.
3300 SERIES (FIRE-RATED) 8300 SERIES (LIFE-SAFETY) MORTISE EXIT DEVICE EXIT DEVICES 3300 Series (Fire-Rated) 8300 Series (Life-Safety) Mortise Exit Device Features STRIKES • Heavy duty deadlatching mechanism • Strong, durable construction for a high level of security • See CYLINDERS section of this catalog for cylinder make, thumbturn and trim ring information. (Available separately).
ED-6 3300 SERIES (FIRE-RATED) 8300 SERIES (LIFE-SAFETY) MORTISE EXIT DEVICE Options and Accessories SILENT ELECTRIFICATION MOTORIZED LATCH RETRACTION EXIT DEVICES HOW TO ORDER • The SE Motorized Latch Retraction option provides near-silent operation for quiet environments such as hospitals, offices, hotels, and libraries where solenoid-driven devices would be disruptive.
8400 SERIES (LIFE-SAFETY) NARROW STILE MORTISE EXIT DEVICE EXIT DEVICES ED-7 MATERIALS 8400 Series (Life-Safety) Narrow Stile Mortise Exit Device • Pushbar made of extruded aluminum, clad or anodized in a variety of finishes. HANDING • Specify handing and bevel if applicable. Lever Entry Trim is field reversible. PUSHBAR LENGTH • Standard sizes: dimensioned for 30", 36", 42", and 48" openings. Standard width bars can be field cut to the next smallest opening width.
8400 SERIES (LIFE-SAFETY) NARROW STILE MORTISE EXIT DEVICE ED-8 EXIT DEVICES Thick and Cladded Door Kits REQUEST TO EXIT (REX) – MONITOR / SIGNAL SWITCH • Mounted in the exit device pushbar on the hinge end, the switch can be used to activate signal light, horn, monitor, or other devices.
3600 SERIES (FIRE-RATED) 8500 SERIES (LIFE-SAFETY) METAL DOOR CONCEALED VERTICAL ROD EXIT DEVICE EXIT DEVICES 3600 Series (Fire-Rated) 8500 Series (Life-Safety) Metal Door Concealed Vertical Rod Exit Device Features DOGGING • Strong, durable construction for a high level of security • Standard dogging with hex key or optional cylinder dogging for 8500 Series only. Electric dogging also available for 3600 and 8500 Series.
ED-10 3600 SERIES (FIRE-RATED) 8500 SERIES (LIFE-SAFETY) METAL DOOR CONCEALED VERTICAL ROD EXIT DEVICE Options and Accessories SILENT ELECTRIFICATION MOTORIZED LATCH RETRACTION EXIT DEVICES HOW TO ORDER • The SE Motorized Latch Retraction option provides near-silent operation for quiet environments such as hospitals, offices, hotels, and libraries where solenoid-driven devices would be disruptive.
EXIT DEVICES 8600 Series (Life-Safety) Narrow Stile Concealed Vertical Rod Exit Device 8600 SERIES (LIFE-SAFETY) NARROW STILE CONCEALED VERTICAL ROD EXIT DEVICE ED-11 MATERIALS • Pushbar made of extruded aluminum, clad or anodized in a variety of finishes. HANDING • Device is non-handed. Lever Entry Trim is field reversible. PUSHBAR LENGTH • Standard sizes: dimensioned for 30", 36", 42", and 48" openings. Standard width bars can be field cut to the next smallest opening width.
8600 SERIES (LIFE-SAFETY) NARROW STILE CONCEALED VERTICAL ROD EXIT DEVICE ED-12 EXIT DEVICES Bolts and Strikes REQUEST TO EXIT (REX) – MONITOR / SIGNAL SWITCH • The patented top latching mechanism utilizes a rotating top bolt which deadlatches around the header strike, interlocking the door to the frame. Supplied with standard header strike. The hexagonal, hardened steel bottom bolt is shielded in a cast housing for strength and stability.
3700 SERIES (FIRE-RATED) 8700 SERIES (LIFE-SAFETY) RIM EXIT DEVICE EXIT DEVICES 3700 Series (Fire-Rated) 8700 Series (Life-Safety) Rim Exit Device 3700 SERIES (FIRE-RATED) 8700 SERIES (LIFE-SAFETY) RIM EXIT DEVICE ED-13 Specifications Starwheel Bolt 3700 SERIES CERTIFICATIONS • UL Panic-Fire Exit Hardware, 3-Hour Fire Label • UL 305 Panic Hardware 1. When door closes, the interlocking noseguard and starwheel bolt close around the strike.
ED-14 3700 SERIES (FIRE-RATED) 8700 SERIES (LIFE-SAFETY) RIM EXIT DEVICE Options and Accessories SILENT ELECTRIFICATION MOTORIZED LATCH RETRACTION EXIT DEVICES HOW TO ORDER • The SE Motorized Latch Retraction option provides near-silent operation for quiet environments such as hospitals, offices, hotels, and libraries where solenoid-driven devices would be disruptive.
EXIT DEVICES 8800 Series (Life-Safety) Narrow Stile Rim Exit Device 8800 SERIES (LIFE-SAFETY) NARROW STILE RIM EXIT DEVICE ED-15 MATERIALS • Pushbar made of extruded aluminum, clad or anodized in a variety of finishes. HANDING • Device is non-handed. Lever Entry Trim is field reversible. PUSHBAR LENGTH • Standard sizes: dimensioned for 30", 36", 42", and 48" openings. Standard width bars can be field cut to the next smallest opening width. DOOR THICKNESS • Suits 1-3/4" standard, up to 2-1/4".
8800 SERIES (LIFE-SAFETY) NARROW STILE RIM EXIT DEVICE ED-16 EXIT DEVICES Strike of the rim exit device from a remote location or access control device. The EL option is available for rim exit devices only. • Made of hardened steel. Standard strike and narrow versions for centering doors in 4" jamb. (Both strikes are included.) ALARMED EXIT DEVICE • This battery-operated option emits a loud (95 decibel) alarm to notify management of unauthorized exit. Available on minimum opening width 36".
3900 SERIES (FIRE-RATED) 8900 SERIES (LIFE-SAFETY) WOOD DOOR CONCEALED VERTICAL ROD EXIT DEVICE EXIT DEVICES 3900 Series (Fire-Rated) 8900 Series (Life-Safety) Wood Door Concealed Vertical Rod Exit Device Features 3080 ENTRY TRIM (FUNCTIONS 08, 09) • Patented top latching mechanism interlocks door to frame • Strong, durable construction for a high level of security • Innovative top rod only design makes preparation easier and reduces maintenance ELECTRIFIED OPTION FIRE RATED GRADE 3900 SERIES ONL
ED-18 3900 SERIES (FIRE-RATED) 8900 SERIES (LIFE-SAFETY) WOOD DOOR CONCEALED VERTICAL ROD EXIT DEVICE Options and Accessories SILENT ELECTRIFICATION MOTORIZED LATCH RETRACTION • The SE Motorized Latch Retraction option provides near-silent operation for quiet environments such as hospitals, offices, hotels, and libraries where solenoid-driven devices would be disruptive.
EXIT DEVICES Options & Accessories for Exit Devices Adams Rite Exit Devices can be ordered with electrification options for standalone access control or integration with maglocks, card readers, keypads, fire alarms, power door operators, and other control systems. Different exit device types have different installation and power requirements. Please refer to product pages for more information on all available exit device types, functions, installation requirements and complete How-to-Order guides.
ED-20 EXIT DEVICES OPTIONS & ACCESSORIES FOR EXIT DEVICES Request to Exit – Monitor/Signal Switch Not to be used as an access control element. SE Motorized Latch Retraction option or LR Latch Retraction option is recommended with access control devices such as card readers or keypads.
ELECTRIC STRIKES 7100, 7101 ELECTRIC STRIKES ES-1 Specifications 7100, 7101 Electric Strikes FAIL-SAFE/FAIL-SECURE • Field convertible from one mode to the other. However, AC intermittent solenoid must not be used continuously in either. CASE • Approximately 1" x 3-3/8" x 1-5/8" deep. STRIKE LIP ALUMINUM UL BURGLARY LISTED ELECTRIFIED PRODUCT GRADE 1 E09321 • Basic 7100 strike has lip of proper length for 1-3/4" thick door that closes flush with jamb edge.
ES-2 ELECTRIC STRIKES 7100, 7101 ELECTRIC STRIKES All measurements are approximate and are provided for informational purposes only. Refer to the product Installation Instructions. Dimensions Jamb Preparation 1-1/4" 1-15/32" 37.3mm 31.8mm CYLINDER OF ADAMS RITE LATCH 1/4" 6.4mm 6-1/8" 155.8mm 1-1/8" 28.6mm 1-7/16" 1" 2-5/8" 1-5/8" RADIUS FACE OF 7101 1-1/16" 123.8mm HORIZONTAL OF ELECTRIC STRIKE AND LATCHBOLT 66.7mm 41.3mm 4-7/8" 36.5mm 25.4mm 3-3/8" 27mm 85.
ELECTRIC STRIKES 7110, 7111 ELECTRIC STRIKES ES-3 Specifications 7110, 7111 Electric Strikes FAIL-SAFE/FAIL-SECURE • Field convertible from one mode to the other. However, AC intermittent solenoid must not be used continuously in either. CASE • Approximately 1" x 3-3/8" x 1-5/8" deep. STRIKE LIP ALUMINUM HOLLOW METAL WOOD UL BURGLARY LISTED ELECTRIFIED PRODUCT GRADE 1 E09321 • Basic 7110 strike has lip of proper length for 1-3/4" thick door that closes flush with jamb edge.
ES-4 ELECTRIC STRIKES 7110, 7111 ELECTRIC STRIKES All measurements are approximate and are provided for informational purposes only. Refer to the product Installation Instructions. Dimensions Jamb Prep in Aluminum 7110: 9-3/16" 1-15/32" HORIZONTAL OF CYLINDER (A-R 4500/4900 SERIES DEADLATCH) 1/4" 37.3mm 6.4mm 1-1/8" 233.4mm 28.6mm 7111: 11-1/2" 292.1mm 1-7/16" 1" 7110: 36.5mm 25.4mm 7-15/16" HORIZONTAL OF ELECTRIC STRIKE 1-5/8" 201.6mm 7111: 10-1/8" 41.3mm 257.
ELECTRIC STRIKES 7130, 7131 ELECTRIC STRIKES ES-5 Specifications 7130, 7131 Electric Strikes FAIL-SAFE/FAIL-SECURE • Field convertible from one mode to the other. However, AC intermittent solenoid must not be used continuously in either. CASE • Approximately 1" x 3-3/8" x 1-5/8" deep. STRIKE LIP ALUMINUM UL BURGLARY LISTED ELECTRIFIED PRODUCT GRADE 1 E09321 • Basic 7130 strike has lip of proper length for 1-3/4" thick door that closes flush with jamb edge.
ES-6 ELECTRIC STRIKES 7130, 7131 ELECTRIC STRIKES All measurements are approximate and are provided for informational purposes only. Refer to the product Installation Instructions. Dimensions 1-15/32" 37.3mm Jamb Preparation HORIZONTAL OF CYLINDER (A-R 4500/4900 SERIES DEADLATCH) 1/4" 6.4mm 1-1/8" 8-1/4" 28.6mm 209.6mm HORIZONTAL OF ELECTRIC STRIKE 1" 25.4mm 1-5/8" 6-7/8" 1-7/16" 174.6mm 36.5mm 2-9/16" 65.1mm 41.3mm 1-1/16" 27mm RADIUS FACE OF 7131 21/32" 16.7mm 3-3/8" 85.
ELECTRIC STRIKES 7140 ELECTRIC STRIKES ES-7 Specifications 7140 Electric Strikes FAIL-SAFE/FAIL-SECURE • Field convertible from one mode to the other. However, AC intermittent solenoid must not be used continuously in either. CASE • Approximately 1" x 3-3/8" x 1-5/8" deep. STRIKE LIP HOLLOW METAL WOOD UL BURGLARY LISTED ELECTRIFIED PRODUCT GRADE 1 E09321 • Basic 7140 strike has lip of proper length for 1-3/4" thick door that closes flush with jamb edge.
ES-8 ELECTRIC STRIKES 7140 ELECTRIC STRIKES All measurements are approximate and are provided for informational purposes only. Refer to the product Installation Instructions. Dimensions Jamb Prep in Wood 1-15/32" 37.3mm VERTICAL OF DEADLATCH MOUNTING SCREWS IN SAME PLANE AS ELECTRIC STRIKE MOUNTING SCREWS 1/4" 6.4mm 1-11/64" 1-1/8" 29.8mm 28.6mm HORIZONTAL OF CYLINDER (A-R 4500/4900 SERIES DEADLATCH) 1" 25.4mm 1-5/8" 1-3/64" 26.6mm 4-1/8" 3/16" 1-7/16" 3-3/8" 104.8mm 4.
ELECTRIC STRIKES 7160 ELECTRIC STRIKE ES-9 Specifications 7160 Electric Strike FAIL-SAFE/FAIL-SECURE • Field convertible from one mode to the other. However, AC intermittent solenoid must not be used continuously in either. CASE • Approximately 1" x 3-3/8" x 1-7/8" deep. STRIKE LIP ALUMINUM UL BURGLARY LISTED ELECTRIFIED PRODUCT GRADE 1 E09321 • Basic 7160 strike has lip of proper length for 1-3/4" thick door that closes flush with jamb edge.
ES-10 ELECTRIC STRIKES 7160 ELECTRIC STRIKE All measurements are approximate and are provided for informational purposes only. Refer to the product Installation Instructions. Dimensions Jamb Preparation Nominal, subject to tolerance extremes 1-9/16" HORIZONTAL OF ELECTRIC STRIKE AND LATCHBOLT (NOT PER STANDARD ANSI PREP LOCATION) 1/4" 39.7mm 6.4mm 1-1/8" 6-1/8" 155.6mm 28.6mm 4-7/8" 1" 123.8mm 3-3/8" 25.4mm 85.7mm 20° 1-1/2" 38.1mm 1-13/16" 46mm 1" 25.4mm 5/32" 4mm R 27/32" 21.
ELECTRIC STRIKES 7170 ELECTRIC STRIKE ES-11 Specifications 7170 Electric Strike FAIL-SAFE/FAIL-SECURE • Field convertible from one mode to the other. However, AC intermittent solenoid must not be used continuously in either. CASE • Approximately 1" x 3-3/8" x 1-7/8" deep. STRIKE LIP HOLLOW METAL WOOD UL BURGLARY LISTED ELECTRIFIED PRODUCT GRADE 1 E09321 • Basic 7170 strike has lip of proper length for 1-3/4" thick door that closes flush with jamb edge.
ES-12 ELECTRIC STRIKES 7170 ELECTRIC STRIKE All measurements are approximate and are provided for informational purposes only. Refer to the product Installation Instructions. Dimensions Jamb Prep in Wood VERTICAL OF DEADLATCH MOUNTING SCREWS IN SAME PLANE AS ELECTRIC STRIKE MOUNTING SCREWS 1-9/16" 1/4" 39.7mm 6.4mm 1-1/8" 1-3/8" 34.9mm 1-1/8" 28.6mm 28.6mm 1" 4-1/8" 25.4mm 20° 1/8" HORIZONTAL OF STRIKE SAME AS HORIZONTAL OF LATCHBOLT 1-1/2" 3.2mm 104.8mm 4-7/8" 3-3/8" 123.8mm 85.
ELECTRIC STRIKES 7240 FIRE-RATED ELECTRIC STRIKE ES-13 Specifications 7240 Fire-Rated Electric Strike UL10C, CAN/ULC-S104, FIRE RATED 3 HR. CASE • Approximately 1" x 3-3/8" x 1-5/8" deep. STRIKE LIP • Basic 7240 strike has lip of proper length for 1-3/4" thick door that closes flush with jamb edge. STRIKE OPENING UL BURGLARY LISTED HOLLOW METAL • 5/8" x 1-7/16" x 9/16" deep. Bolt retainer jaw and strike lip are stainless steel. Strike accepts bolt from a variety of latchsets.
ES-14 ELECTRIC STRIKES 7240 FIRE-RATED ELECTRIC STRIKE All measurements are approximate and are provided for informational purposes only. Refer to the product Installation Instructions. Dimensions Installation in Steel Jamb 1-15/32" 37.3mm MOUNTING BRACKET WELDED TO JAMB VERTICAL OF ELECTRIC STRIKE FACEPLATE DIRECTLY OPPOSITE OF DEADLATCH 1/4" 6.4mm 1-1/8" 28.6mm 1" HORIZONTAL OF ELECTRIC STRIKE SAME AS HORIZONTAL OF LATCHBOLT 25.4mm 1-5/8" 4-1/8" 104.8mm 41.
ELECTRIC STRIKES 7270 FIRE-RATED ELECTRIC STRIKES ES-15 Specifications 7270 Fire-Rated Electric Strikes UL10C, CAN/ULC-S104, FIRE RATED 3 HR. CASE • Approximately 1" x 3-3/8" x 1-7/8" deep. STRIKE LIP • Basic 7270 strike has lip of proper length for 1-3/4" thick door that closes flush with jamb edge. STRIKE OPENING HOLLOW METAL UL BURGLARY LISTED ELECTRIFIED PRODUCT FIRE RATED HOUR GRADE 1 E09321 • 3/4" x 1-7/16" x 5/8" deep. Bolt retainer jaw and strike lip are stainless steel.
ES-16 ELECTRIC STRIKES 7270 FIRE-RATED ELECTRIC STRIKES All measurements are approximate and are provided for informational purposes only. Refer to the product Installation Instructions. Dimensions Installation in Steel Jamb 1-9/16" 39.7mm 1-1/8" MOUNTING BRACKET (MOUNTING CLIP) WELDED TO JAMB (OR PROVIDED) VERTICAL OF DEADLATCH MOUNTING SCREWS IN SAME PLANE AS ELECTRIC STRIKE MOUNTING SCREWS 1/4" 6.4mm 28.6mm 1" 25.4mm 20° 4-1/8" 1-1/2" 104.8mm 38.1mm 1-13/16" 1" 46mm 25.4mm 1/8" 3.
ULTRALINE 7400, 7401 ELECTRIC STRIKES ELECTRIC STRIKES Ultraline 7400, 7401 Electric Strikes ES-17 Specifications FAIL-SAFE/FAIL-SECURE • Field selectable at time of installation. CASE • Approximately 1" x 3-3/8" x 1-1/16" deep. STRIKE LIP • Basic 7400 electric strike has lip of proper length for 1-3/4" thick door that closes flush with jamb edge. Where door thickness or jamb shape differs from this configuration, lip extension kits are available. Not available on 7401.
ULTRALINE 7400, 7401 ELECTRIC STRIKES ES-18 ELECTRIC STRIKES All measurements are approximate and are provided for informational purposes only. Refer to the product Installation Instructions. Dimensions Jamb Preparation 1-1/4" 31.8mm CYLINDER OF ADAMS RITE LATCH 1-13/32" 35.7mm 6-1/8" 155.6mm 1-7/16" 36.5mm 4-7/8" 123.8mm 1-1/16" 1-21/32" 27mm 42.1mm HORIZONTAL OF ELECTRIC STRIKE AND LATCHBOLT RADIUS FACE OF 7401 1-11/16" 3-3/8" 85.7mm 42.9mm 5/32" 4mm R (4 PLACES) 1-1/4" 31.
ULTRALINE 7410, 7411 ELECTRIC STRIKES ELECTRIC STRIKES ES-19 Specifications Ultraline 7410, 7411 Electric Strikes FAIL-SAFE/FAIL-SECURE • Field selectable at time of installation. CASE • Approximately 1" x 3-3/8" x 1-1/16" deep. STRIKE LIP • Basic 7400 electric strike has lip of proper length for 1-3/4" thick door that closes flush with jamb edge. Where door thickness or jamb shape differs from this standard relationship, lip extension kits are available.
ULTRALINE 7410, 7411 ELECTRIC STRIKES ES-20 ELECTRIC STRIKES All measurements are approximate and are provided for informational purposes only. Refer to the product Installation Instructions. Dimensions Jamb Preparation 1-7/16" 36.5mm 1-13/32" 35.7mm 7410: 1-1/16" 21/32" 27mm 16.7mm 7-15/16" HORIZONTAL OF STRIKE SAME AS HORIZONTAL OF LATCH BOLT 7410: 7-7/16" 188.9mm 3-3/8" 1-7/16" 85.7mm 36.5mm 1-25/32" 201.6mm 45.2mm 7411: 7411: 10-1/4" 9-29/64" 260.4mm 240.
ULTRALINE 7430, 7431 ELECTRIC STRIKES ELECTRIC STRIKES ES-21 Specifications Ultraline 7430, 7431 Electric Strikes FAIL-SAFE/FAIL-SECURE • Field selectable at time of installation. CASE • Approximately 1" x 3-3/8" x 1-1/16" deep. STRIKE LIP • Basic 7400 electric strike has lip of proper length for 1-3/4" thick door that closes flush with jamb edge. Where door thickness or jamb shape differs from this standard relationship, lip extension kits are available. Not available on 7431.
ULTRALINE 7430, 7431 ELECTRIC STRIKES ES-22 ELECTRIC STRIKES All measurements are approximate and are provided for informational purposes only. Refer to the product Installation Instructions. Dimensions Jamb Preparation 1-1/4" 31.8mm 21/32" 16.7mm 1-13/32" HORIZONTAL OF CYLINDER (A-R 4500) SERIES DEADLATCH 35.7mm 1-1/16" 21/32" 27mm 16.7mm 6-7/8" 174.6mm 1-7/16" 1-11/16" 42.9mm 36.5mm RADIUS FACE OF 7431 3-3/8" 85.7mm 8-1/8" 206.4mm HORIZONTAL OF ELECTRIC STRIKE 1-1/4" 3/32" 31.
ELECTRIC STRIKES ULTRALINE 7440 ELECTRIC STRIKES Ultraline 7440 Electric Strikes ES-23 Specifications FAIL-SAFE/FAIL-SECURE • Field selectable at time of installation. CASE • Approximately 1" x 3-3/8" x 1-1/16" deep. STRIKE LIP • Basic 7400 electric strike has lip of proper length for 1-3/4" thick door that closes flush with jamb edge. Where door thickness or jamb shape differs from this standard relationship, lip extension kits are available.
ES-24 ELECTRIC STRIKES ULTRALINE 7440 ELECTRIC STRIKES All measurements are approximate and are provided for informational purposes only. Refer to the product Installation Instructions. Dimensions Jamb Preparation 1-1/4" 31.8mm 21/32" HORIZONTAL OF CYLINDER (A-R 4500 & 4700 SERIES DEADLATCHES) 1-13/32" 35.7mm 16.7mm 4-7/8" 1-7/16" 1-1/16" 21/32" 3-3/8" 36.5mm 27mm 16.7mm 4-1/8" 104.8mm 3-5/8" 85.7mm 1-11/16" 42.9mm 123.8mm 92.1mm HORIZONTAL OF ELECTRIC STRIKE 1-1/4" 31.
ELECTRIC STRIKES ULTRALINE 74R1 ELECTRIC STRIKE Ultraline 74R1 Electric Strike ES-25 Specifications FAIL-SAFE/FAIL-SECURE • Field selectable at time of installation. CASE • Approximately 1" x 3-3/8" x 1-1/16" deep. MOUNTING PLATE/HOUSING • Made of zinc aluminum alloy and measures 1-3/4" x 9" x 11/16" deep. Standard finish in epoxy to match Clear, Dark Bronze Anodized and Black Anodized finishes.
ES-26 ELECTRIC STRIKES ULTRALINE 74R1 ELECTRIC STRIKE All measurements are approximate and are provided for informational purposes only. Refer to the product Installation Instructions. Dimensions Jamb Preparation 1-17/32" 38.9mm Ø 3/16 DRILL 1-27/64" 36.1mm 7/32" 5.6mm 1-41/64" 41.7mm 1/4" 6.4mm 11/16" 17.5mm 1/8" 2-1/4" 3.2mm 57.2mm 4-1/2" 114.3mm 8-1/4" 209.6mm 15/16" 23.8mm 1-5/8" 41.3mm 8-1/4" 209.6mm 3-3/8" 85.7mm 9" 228.6mm Installation 7/8" 22.
ELECTRIC STRIKES Ultraline 74R2 Electric Strike ULTRALINE 74R2 ELECTRIC STRIKE ES-27 Specifications FAIL-SAFE/FAIL-SECURE • Field selectable at time of installation. CASE • Approximately 1" x 3-3/8" x 1-1/8" deep. STRIKE OPENING • Bolt retainer jaw is stainless steel, measures 5/8" x 1-7/16" x 1/2" deep. MOUNTING PLATE/HOUSING ALUMINUM UL BURGLARY LISTED ELECTRIFIED PRODUCT GRADE 1 E09321 • Made of zinc aluminum alloy and measure 1-5/8" x 9" x 1/2" deep.
ES-28 ELECTRIC STRIKES ULTRALINE 74R2 ELECTRIC STRIKE All measurements are approximate and are provided for informational purposes only. Refer to the product Installation Instructions. Dimensions Jamb Preparation 1-5/8" 7/8" INSIDE FACE OF CLOSED DOOR 41.3mm 22.2mm 5/32" 4mm 1-5/8" 1-19/32" 41.3mm 40.5mm 7/8" 22.2mm 8-1/4" 209.6mm 4-1/2" 114.3mm 1/2" 1-5/8" 12.7mm 41.3mm 9" Installation 228.6mm 3-3/8" 8-1/4" 85.7mm 209.
ELECTRIC STRIKES OPTIONS & ACCESSORIES FOR ELECTRIC STRIKES Options & Accessories for Electric Strikes ES-29 Lip Extension Kits for Ultraline 7400 Series Electric Strikes Lip extensions are for center hung doors, thick doors, or other conditions that vary from the “standard” 1-3/4" thick door that closes flush (or near flush) with the jamb face. Lip extension kits are available in 1/8" increments.
ES-30 ELECTRIC STRIKES OPTIONS & ACCESSORIES FOR ELECTRIC STRIKES LIP EXTENSION EXTENSION WDC7400 Wood Door Application Power For use with Ultraline 7400 Electric Strikes only, this cover plate is designed to simplify mortising of wood door pairs. 4603 RECTIFIER JAMB WDC7400 Converts low voltage AC current to DC of same voltage. Installs in low voltage line between transformer and strike. Full wave bridge type. Rated 2 amps (200 PIV).
TRIM T-1 1000 TURNS Specifications TURN LEVER 1000 Turns • Zinc alloy. Trim finish RC130. ESCUTCHEON 5/8" CSK FOR 15.9mm • Stainless #6 FLAT HEAD SCREW Steel. Trim finish in RC130. 5/16" 7.9mm SPINDLES The 1000 Turns are designed to operate Adams Rite MS1847 Deadlocks and the 5017 Wood Door Deadlock. L* 5/32" 4mm 1/4" 6.4mm • Hardened steel, plated for corrosion resistance. First 1/4" 23/32" dash number in order guide indicates spindle parallel 6.4mm 18.
L* 25/32" 19.8mm MS1847-06 MS1847-13 DOOR PULL 1000 TURNS T-2 TRIM TO FACE OF LOCK CLEARANCE HOLE FOR SPINDLE OPERATION. THIS MUST LINE UP WITH HUB IN LOCK. 1/4" All measurements are approximate and are provided for informational purposes only. TO Refer to the product Installation FOR Instructions. REFER INSTALLATION INSTRUCTIONS 6.4mm ADDITIONAL INFORMATION. L* = A + B TURN Dimensions 15.9mm L* 5/16" 7.9mm 5/32" 1/4" OF LOCK 1/8" MAX. 5/8" 4mm 6.4mm 15.9mm 3.
TRIM T-3 3080 SERIES ENTRY TRIM 3080E Electrified Entry Trim Function 3080 Series Entry Trim The 3080E Electrified Entry Trim provides a continuous duty solenoid mounted to the trim, which enables remote activation of the locking function without unlatching the door, making this trim ideal for stairwell and fire doors. 3080 SERIES ENTRY TRIM 3001 & 3002 Fixed Pulls US32D Satin Stainless Steel pulls have 2-3/4" x 11-1/2" escutcheon. Order with or without cylinder hole.
CYLINDER T-4 TRIM 3080 SERIES ENTRY TRIM ESCUTCHEON All measurements are approximate and are provided for informational purposes only. Refer to the product Installation Instructions. Dimensions 3080-01* 3080E-01* 3080-02* 3080E-02* 3-1/4" 82.6mm 3080-03* 3080E-03* 3-15/32" 88.1mm 5" CYLINDER 73.8mm 4-11/32" 110.3mm CYLINDER RETAINER RING ESCUTCHEON 115.9mm 8-3/32" 8-3/32" 205.6mm 8-3/32" 205.6mm SPACER 205.6mm 48.4mm 48.4mm 48.4mm 3080-ME 3080E-ME 3-5/16" 84.
TRIM eForce®-150 3090 Keyless Entry EFORCE®-150 3090 KEYLESS ENTRY T-5 Operation In the standard mode of operation, a programmed 2 to 7-digit character followed by a star (*) key allows for one entry when used with Adams Rite deadlatches or exit devices. The MS Deadlocks must always be relocked manually when used with the eForce 3090. Hold open time is adjustable from 1 to 9 seconds.
TRIM EFORCE®-150 3090 KEYLESS ENTRY T-6 All measurements are approximate and are provided for informational purposes only. Refer to the product Installation Instructions. Dimensions Stile Preparation 1-7/16" 4X ø 1/4" 36.5mm 6.4mm 3-7/8" ONE WALL ONLY INSTALL RIVNUT 1/2" 98.4mm 12.7mm 2" 50.8mm CL 6-13/32" OF CYLINDER PREP 162.7mm 11-15/16" 303.2mm Installation 5" 15-3/8" 127mm 390.5mm 7-19/32" 192.9mm 7/8" 22.23mm 1-3/4" 44.
TRIM eForce® 3090P, 3090C Keyless Entry EFORCE® 3090P, 3090C KEYLESS ENTRY T-7 Features • Non-handed with clutched lever protection • Key override via mortise cylinder (1" to 1 1/2" length with MS® cam) • Surface mounted with concealed fasteners (1-3/4" to 2-1/4" door thickness) • Temperature range: -31°F to 151°F (-35°C to 65°C) and 5-95% humidity (non-condensing) Specifications ELECTRICAL SPECS: eFORCE 3090P PROX ELECTRIFIED PRODUCT • Integrated HID® 125 KHz Prox contactless card reader • Interface
TRIM EFORCE® 3090P, 3090C KEYLESS ENTRY T-8 All measurements are approximate and are provided for informational purposes only. Refer to the product Installation Instructions. Dimensions Stile Preparation 1-7/16" 36.5mm 4X ø 1/4" 6.4mm 3-7/8" ONE WALL ONLY INSTALL RIVNUT 1/2" 98.4mm 12.7mm 2" 50.8mm 6-13/32" CL 162.7mm OF CYLINDER PREP 11-15/16" Installation 303.2mm 5" 15-3/8" 127mm 390.5mm 7-19/32" 192.9mm 7/8" 22.2mm 1-3/4" 44.
TRIM A100-3090H Keyless Entry Control and Aperio® Hub A100-3090H KEYLESS ENTRY CONTROL AND APERIO® HUB T-9 Features • Aperio wireless technology • Vandal resistant lever with break-away (resettable) clutch • Key override via mortise cylinder (1 to 1 1/2" length with MS® cam, available separately) • Surface mounted with concealed fasteners (1-3/4" to 2-1/4" door thickness) • Temperature range: -31°F to 151°F (-35°C to 65°C) and 5-95% humidity (non-condensing) • Efficiant power usage; 4 x AA Alkaline, inc
A100-3090H KEYLESS ENTRY CONTROL AND APERIO® HUB T-10 TRIM All measurements are approximate and are provided for informational purposes only. Refer to the product Installation Instructions. Dimensions Stile Preparation Installation 1-7/16" 36.5mm 4X ø 1/4" 6.4mm 3-7/8" 1/2" 98.4mm ONE WALL ONLY INSTALL RIVNUT 12.7mm 2" 50.8mm 6-13/32" CL 162.7mm OF CYLINDER PREP 11-15/16" 303.2mm 5" 15-3/8" 127mm 390.5mm 7-19/32" 192.9mm 7/8" 22.2mm 1-3/4" 44.
TRIM 4550 MS® DEADLOCK LEVER T-11 Operation 4550 MS® Deadlock Lever Turn lever downward 90° to unlock. When released, lever returns to horizontal. Turn lever upward 90° to relock. Key operation from outside is not affected. Clutching action prevents damage to internal components. Specifications HOUSING The 4550 MS Deadlock Lever easily unlocks an MS Deadlock with approximately three pounds of downward force. The spring-loaded lever relocks with an upward motion.
TRIM 4550 MS® DEADLOCK LEVER T-12 All measurements are approximate and are provided for informational purposes only. Refer to the product Installation Instructions. Dimensions Stile Preparation CYLINDER BACKSET 2-15/32" 62.7mm 11/16" 90˚ TO LOCK 1-13/32" 17.5mm 35.7mm 10-32 (4 PLCS) 11/32" 8.7mm 1-19/32"(REF) 40.5mm CYLINDER 3/16" 4-17/64" 108.3mm 2-57/64" 4.8mm 73.4mm 29/64" 11.5mm 6-13/64" 157.6mm 2-3/32" 53.2mm 3-5/32" 7-15/64" 80.2mm 183.8mm 7/8" DIA. (2 PLCS) 22.
TRIM 4560, 4565 DEADLATCH HANDLES 4560, 4565 Deadlatch Handles T-13 Specifications 4560 HANDLE • ADA Compliant lever is shaped to fit the hand, with a concave thumb-rest portion that tends to keep knuckles and thumb safely away from the jamb, even on a short backset narrow stile. 4565 HANDLE The 4560 and 4565 Deadlatch Handles easily unlock the 4300, 4500 and 4900 Series Deadlatches. These handles fit solidly into the cylinder hole of the latch.
TRIM 4560, 4565 DEADLATCH HANDLES T-14 All measurements are approximate and are provided for informational purposes only. Refer to the product Installation Instructions. Dimensions Narrow Stile Preparation 4560 LATCH BACKSET 104.8mm 12.7mm 11.1mm 5/8" 4-1/8" 13/32" 1/2" 10.3mm 7/16" STILE 43/64" 17.1mm 15.9mm 3" 76.2mm 4" 101.6mm 57/64" 22.6mm 3" 1-23/32" 76.2mm 43.7mm LATCH CYLINDER 3/64" 11/64" 1.2mm 4.4mm 1-51/64" 45.6mm 1-1/4" DIA. 31.8mm 1-11/32" 34.
TRIM 4568, 4569 EUROSTYLE DEADLATCH HANDLES 4568, 4569 Eurostyle Deadlatch Handles T-15 Specifications LEVERS • Lever of cast aluminum, in choice of 130 Satin Aluminum, 121 Dark Bronze, or 119 Black. Modern European styling offers a generous hand grip with shank offset from the narrow stile jamb for hand safety. 4569 has return end to meet anti-snag code requirements. ESCUTCHEONS The 4568 and 4569 Deadlatch Handles easily unlock the 4300, 4500 and 4900 Series Deadlatches.
TRIM 4568, 4569 EUROSTYLE DEADLATCH HANDLES T-16 All measurements are approximate and are provided for informational purposes only. Refer to the product Installation Instructions. Dimensions 4568 Narrow Stile Preparation 1-11/32" 41/64" LATCH BACKSET STILE 34.1mm Wood Door Preparation LATCH BACKSET 5/32" 16.3mm 4mm 3" 4-3/16" HOLE LOCATIONS SAME AS ON LEFT 76.2mm 125.8mm CYLINDER 1-23/32" 43.7mm LATCH CYLINDER 2-11/32" 4-23/32" 59.5mm 119.9mm 1-1/4" DIA. 1-1/4" DIA. 31.
TRIM 4590 Deadlatch Paddle 4590 DEADLATCH PADDLE T-17 Specifications PADDLE • Extruded aluminum, 628 Clear Anodized finish (US28). 313 Dark Bronze Anodized and 335 Black Anodized are also available. ESCUTCHEON The 4590 Deadlatch Paddle is an ergonomically-friendly alternative to a knob or lever handle. Operate with a simple push or pull. Function An alternative to knob or lever handles.
TRIM 4590 DEADLATCH PADDLE T-18 All measurements are approximate and are provided for informational purposes only. Refer to the product Installation Instructions. Dimensions Stile Preparation For 4500/4900 latches, see MS+1890/2190 for different hole pattern BACKSET 9/32" 7.1mm DIA. (2 PLCS) STILE 5-29/32" 150mm 1" PUSH* 25.4mm 3" 76.2mm PULL* 2-5/16" 4" 58.7mm 101.6mm 1-19/64" 9/16" 32.9mm 1-23/32" 14.2mm 43.7mm LATCH CYL. *SHOWN AT REST. 1-29/32" PADDLE TRAVEL IS: 48.
TRIM 4591 Deadlatch Paddle 4591 DEADLATCH PADDLE T-19 Specifications PADDLE • Extruded aluminum, 628 Clear Anodized finish (US28). 313 Dark Bronze Anodized and 335 Black Anodized are also available. US3 Bright Brass, US26 Bright Chrome, or US26D Satin Chrome plating is also available. ESCUTCHEON The 4591 Deadlatch Paddle is an ergonomically-friendly alternative to a knob or lever handle. Operate with a simple push or pull. Function An alternative to knob or lever handles.
TRIM 4591 DEADLATCH PADDLE T-20 All measurements are approximate and are provided for informational purposes only. Refer to the product Installation Instructions. Stile Preparation Dimensions For 4500/4900 latches, see MS+1890/2190 for different hole pattern 5" 127mm BACKSET PUSH* 21/64" DIA. 8.3mm (2 PLCS) STILE PULL* 2-1/16" 77.8mm 4-5/32" 105.6mm 1-51/64" 3" 7/8" 45.6mm 76.2mm 22.2mm *SHOWN AT REST. 2" PADDLE TRAVEL IS: 50.8 mm 1-11/32" 1-1/2" 34.1mm 38.1mm LATCH CYL.
TRIM 4600 HEAVY DUTY DESIGNER DEADLATCH HANDLES 4600 Heavy Duty Designer Deadlatch Handles Specifications The 4600 Heavy Duty Designer Deadlatch Handles are designed with a patented adjustable drive mechanism to operate the 4300, 4500, and 4900 Series Deadlatches and Dual Force 2190/2290 Interconnected Deadbolt/ Deadlatch locksets.
T-22 TRIM 4600 HEAVY DUTY DESIGNER DEADLATCH HANDLES All measurements are approximate and are provided for informational purposes only. Refer to the product Installation Instructions. Dimensions Metal Door Preparation 2X, Ø 1/4" THRU ONE WALL INSTALL RIVNUT 5/32" 4mm VARIES BY HANDLE STYLE 3-29/32"MAX 99.2mm CYLINDER HOLE AS PREPARED FOR 4900 LATCH Ø 1-1/8" BACKSET 1" 15/32" 1-11/32" 25.4mm 11.9mm 34.1mm 1-1/2" 38.1mm 15/16" 23.8mm 5" 127mm 2-15/32" 62.7mm 1-3/16" 6-21/32" 30.
CYLINDERS 4024, 4025, 4026 CYLINDER PULLS 4024, 4025, 4026 Cylinder Pulls ANSI/BHMA 156.5–2010 E 19231 The 4024, 4025, 4026 Cylinder Pulls are designed to operate Adams Rite MS1847 Deadlocks and the 5017 Wood Door Deadlock. C-1 4024 Cylinder Pull The 4024 five pin tumbler cylinder is smaller than the 4025 Cylinder Pull and it is symmetrical, designed for mounting door pull or other trim plate.
C-2 CYLINDERS 4024, 4025, 4026 CYLINDER PULLS All measurements are approximate and are provided for informational purposes only. Refer to the product Installation Instructions. Dimensions Stile Preparation For 4025 mounted directly on stile by two through-screws. 4024 2-35/64" 3/4" 1-7/32" 64.7mm 19.1mm 31.0mm 2" 50.8mm 31/32" SPINDLE 24.6mm 2-1/4" 57.2mm 3/8" DIA. MS1847 LOCK 1-61/64" 49.6mm 9.5mm DRILL AND CSK FOR 2 #10-32 THRU SCREWS 1/8" 3.2mm TAP 6-32 (2 PLCS.
CYLINDERS 4036 Mortise Cylinder 4066 Thumbturn ANSI/BHMA 156.5–2010 E 19211 The 4036 Mortise Cylinder provides five-pin security with most Adams Rite locks or latches. The 4066 Thumbturn operates locks or latches without a key. 4036 MORTISE CYLINDER 4066 THUMBTURN C-3 4066 Thumbturn Function To operate lock or latch without key. Interchanges with standard 1-5/32" diameter mortise cylinder. Cams are available to suit the particular Adams Rite lock or latch. (See back for cam specifications.
C-4 CYLINDERS 4036 MORTISE CYLINDER 4066 THUMBTURN All measurements are approximate and are provided for informational purposes only. Refer to the product Installation Instructions. Dimensions -01 Cylinders “By Others” DIMENSIONS OF CAM TO OPERATE: DEADLOCK SERIES DEADLATCH SERIES DIM “A” .800" ± .005" 20.3mm ± .127mm EXIT DEVICES .120" 3.0mm R .182" 4.
CYLINDERS MS4043 CYLINDER GUARD C-5 Specifications MS4043 Cylinder Guard SECURITY RING • Made of hardened steel. Free-swiveling when properly installed. RETAINER RING • Hardened steel, plated for corrosion resistance. Permits security ring to swivel. TRIM FINISH • Powdercoat to match 130 (Aluminum Satin), 121 (Dark Bronze), and 119 (Black). HOLLOW METAL ALUMINUM OPTIONS • MS4043 Cylinder Guard fits a standard 1/8" stile wall. For 1/4" thick stile walls, specify MS4043-01.
C-6 CYLINDERS MS4043 CYLINDER GUARD All measurements are approximate and are provided for informational purposes only. Refer to the product Installation Instructions. Dimensions Stile Preparation STILE WALL 7/16" 11.1mm 3/8" 9.5mm LOCK BACKSET 1-1/2" 1-15/32" 38.1mm 37.3mm DIA. 5/8" 18.3mm 1-9/32" 1-11/32" DIA. 34.1mm DIA. MINIMUM CYLINDER CAM TO SHOULDER* 23/32" 15.9mm 1-5/8" 41.3mm LOCK FACE CUTOUT 32.
ACCESSORIES 4000 SERIES MS® DEADLOCK STRIKES A-1 4001 BOX STRIKE 4000 Series MS Deadlock Strikes ® • Same trim plate as 4000, but with dust box added. Customarily used only for wood construction where the dust box prevents chips, sawdust, and other debris from entering strike. Furnished with both wood and machine screws. • Material & Finish: Trim plate is aluminum, box is steel plated for corrosion resistance. Available in US28 (628) clear anodized, 313 dark bronze anodized, and 335 black anodized.
A-2 ACCESSORIES 4000 SERIES MS® DEADLOCK STRIKES All measurements are approximate and are provided for informational purposes only. Refer to the product Installation Instructions. Dimensions Mortise Jamb Installation 4000 Trim Strike 4001 Box Strike Strike plate only Strike plate with dust box CYLINDER 1/2"* 1/32" 12.7mm DUST BOX .8mm TRIM PLATE *FOR HOOKBOLT ONLY: 53/64" 4-7/8" 21mm 4-7/8" MAY BE SURFACE MOUNTED OR MORTISED 123.8mm 4-1/8" 104.8mm 87.3mm 104.8mm 1-1/4" 3.2mm 31.
ACCESSORIES 4015 Threshold Bolt 4015 THRESHOLD BOLT A-3 Operation 360° turn of key or thumbturn in basic MS® deadlock throws counterbalanced bolt into opposite door and drop-bolt into threshold. Key can be removed only when bolts are in a positively locked or unlocked position. Specifications CYLINDER HEIGHT ALUMINUM • Standard threshold bolt rod is sufficient for cylinder height up to 53-7/16". It is fully threaded and can be cut off for low cylinder heights.
A-4 ACCESSORIES 4015 THRESHOLD BOLT All measurements are approximate and are provided for informational purposes only. Refer to the product Installation Instructions. Dimensions Installation INSTALL ADAPTOR ARM IN LOCK FROM REAR WITH BOLT RETRACTED AS SHOWN. DRIVE PIN THROUGH SLOTS IN LOCK SIDE PLATES PASSING THROUGH HOLE IN THE ADAPTOR ARM. SHOWN WITH MS1851S LOCK 6" 152.4mm ANY BASIC MS® DEADBOLT 9" 228.6mm SHOWN EXTENDED ROD/BOLT LENGTH MUST BE APPROX. 7" CYLINDER HEIGHT 177.
ACCESSORIES 4016 HEADER BOLT A-5 Operation 4016 Header Bolt 360° turn of key or thumbturn in basic MS® deadlock throws counterbalanced bolt into opposite door and hexagonal bolt into header strike. Key can be removed only when bolts are in a positively locked or unlocked position. Specifications DOOR/CYLINDER HEIGHT • The standard version is designed for a 7’ door height with cylinder height as low as 35". Added extension for up to a 10’ door available when ordering.
A-6 ACCESSORIES 4016 HEADER BOLT All measurements are approximate and are provided for informational purposes only. Refer to the product Installation Instructions. Dimensions Installation 11/16" 5/8" BOLT 17.5mm THROW INSTALL ADAPTOR ARM TO LOCK FROM TOP WITH BOLT RETRACTED AS SHOWN. INSTALL PIN THROUGH SLOTS IN LOCK SIDE PLATES, PASSING THROUGH HOLES IN BOTH SIDES OF THE ADAPTOR ARM. 15.6mm PROJECTION TOP OF DOOR CUT TO SUIT CYLINDER HEIGHT 9/32" 7.1mm 1-13/32" 35.7mm 4-3/4" 120.
ACCESSORIES 4085 HEADER BOLT (PAIRS OF DOORS ONLY) A-7 Operation 4085 Header Bolt (Pairs of Doors Only) 360° turn of key or thumbturn in basic MS® deadlock throws counterbalanced bolt into opposite door, kicking positioner bolt into header strike. Positioner bolt may be manually thrown before closing active leaf to reduce effort on key-bow. Key can be removed only when bolts are in a positively locked or unlocked position.
A-8 ACCESSORIES 4085 HEADER BOLT (PAIRS OF DOORS ONLY) All measurements are approximate and are provided for informational purposes only. Refer to the product Installation Instructions. Dimensions Header Preparation for Strike 1-1/2" 38.1mm 1/4" 1-29/32" #6-32 TAP (2) HOLES 1" 25.4mm 6.4mm 48.4mm 1/16" 1-19/32" 1.6mm 40.5mm 1/4" 6.4mm 25-0071 HEADER STRIKE FURNISHED 1-1/2" 29/32" 38.1mm 23mm 1-3/4" 44.5mm HEADER STRIKE 5/8" 15.9mm 1-15/32" 37.3mm SHOWN EXTENDED 2-3/4" 69.
ACCESSORIES 4089 EXIT INDICATOR A-9 Specifications 4089 Exit Indicator MESSAGE PANEL • “OPEN” appears in black letters on white background when lock is retracted and “LOCKED” in red letters when actuated. Also available with red (locked) and green (unlocked) wordless panels. MATERIAL/FINISH • Indicator escutcheon is zinc alloy with 130 (Satin Aluminum) finish. Also available in 119 satin black and 121 dark bronze. Header sign is clear aluminum match with black letters.
A-10 ACCESSORIES 4089 EXIT INDICATOR All measurements are approximate and are provided for informational purposes only. Refer to the product Installation Instructions. Dimensions Aluminium Stile Preparation FOR 31/32" OR 1-1/8" BACKSET CYLINDER BACKSET CYLINDER CUTOUT 3-1/8" 79.4mm 1/16" 1.6mm 1-7/8" 47.6mm 1-7/8" 47.6mm 5/8" 15.9mm 2-5/8" 66.7mm 19/32" 15.1mm 7/8" 22.2mm DIA. (2 PLC’S) TAP 8-32 (2 PLC’S) 11/32" 1" 8.7mm 25.4mm 11/32" 1-11/32" 8.7mm 34.
ACCESSORIES 4800 SERIES STRIKES A-11 4800 Series 4800 Series Strikes HOLLOW METAL WOOD Function With vertical adjustment to accommodate door/jamb misalignment and a shim system for horizontal positioning to match various jamb bumper designs, the 4800 Series Strikes can be fit to nearly any sliding door using a mortised MS1847 Deadlock or latch. 4801 strikes are furnished with sheet metal screws for metal jamb installation.
A-12 ACCESSORIES 4800 SERIES STRIKES All measurements are approximate and are provided for informational purposes only. Refer to the product Installation Instructions. Dimensions Jamb Preparation 4800 Series SHIM(S) AS REQUIRED 9/16" 4800 Series 14.3mm LOCK & STRIKE 1/2" 12.7mm STRIKE 1-11/16" 42.9mm 3-15/16" BOLT CLEARANCE CUTOUT 100mm 4" 101.6mm 25.4mm 71.4mm 2-13/16" MS1847 SHIM LENGTH 1" 2-13/16" 71.4mm 1-13/16" 46mm 1-1/8" 3/8" 28.6mm 9.
ACCESSORIES 4901, 4902 DEADLATCH STRIKES 4901, 4902 Deadlatch Strikes A-13 4901-01 Standard slat strike includes molded black plastic dust box and closure of the unused lower strike opening, with steel mounting plate. Long face is designed to span strike area of MS® deadlocks with which the deadlatch is interchangeable. 4901-02 Same as 4901-01, except with radiused strike plate, for nose of opposite door when latching pairs.
A-14 ACCESSORIES 4901, 4902 DEADLATCH STRIKES All measurements are approximate and are provided for informational purposes only. Refer to the product Installation Instructions. Dimensions 4901 Installation MOUNTING PLATE CSK FOR #10 FLAT HEAD 10-32 TAP 9.5mm 155.6mm 28.6mm 7/64" 2.8mm CYLINDER 4500, 4900 OR EXISTING 4700 1/16" 1.6mm 3/8" 4901-01 FLAT WITH DUST BOX & MOUNTING PLATE 6-1/8" 1-1/8" 117.5mm 9/16" 14.3mm DIM: ‘A’ DUST BOX 3/4" 4-5/8" 11/32" 8.7mm 19.
ACCESSORIES Lock Mounting Methods Lock mounting methods for narrow stile aluminum doors – the three most prevalent methods of mounting locks and latches within the hollow tube stile of glass doors are shown in the accompanying illustrations. A-15 LOCK MOUNTING METHODS Method A 4104 MOUNTING BRIDGE 4104 BRIDGE RESILIENT WASHER LOCK MOUNTING PLATE MOUNTING SCREW Method A: 4104 Mounting Bridge Method B Method “A” spans the stile with a steel bridge at the top and bottom of the lock.
POWER PS-SE POWER SUPPLY P-1 Operating Modes PS-SE Power Supply The PS-SE is designed to power up to two 3000 SE or 8000 SE exit devices in the following operating modes: • Sequential Mode – A single input switch (Dry Contact) operates two devices in sequential operation. Ideal for a double-door setup. • Independent Mode – Each SE exit device is controlled by its own input switch. Specifications UL1012 + UL1310 INPUT POWER • 115 VAC, 0.
P-2 POWER PS-SE POWER SUPPLY All measurements are approximate and are provided for informational purposes only. Refer to the product Installation Instructions. Dimensions 10" 254mm 4-1/8" 104.8mm 9-1/4" 235mm 1-13/64" 30.6mm 10-3/8" 263.5mm Layout & Wiring INPUT #1 N.O. DRY CONTACT SWITCH RATED FOR 15mA PEAK @ 24VDC EXIT DEVICE #2 EXIT DEVICE #1 INPUT #2 N.O. DRY CONTACT SWITCH RATED FOR 15mA PEAK @ 24VDC FIRE ALARM DISABLE N.C.
POWER PS-1 POWER SUPPLY P-3 Specifications PS-1 Power Supply UL 294 INPUT POWER • 110 VAC, 60 Hz, 0.5A OUTPUT VOLTAGE • Field-selectable 12 or 24 VDC, 1 Amp. (Maximum 13.8 VDC/27.6 VDC) PRIMARY FUSE • 800 mA, 5 x 20MM BATTERY FUSE • 2 Amps, 5 x 20MM One amp linear power supply with integrated battery backup circuitry for electric strikes, maglocks, and other access control devices.
P-4 POWER PS-1 POWER SUPPLY All measurements are approximate and are provided for informational purposes only. Refer to the product Installation Instructions. Dimensions 12-1/8" 308mm 4" 101.6mm 8-3/4" 222.3mm 1-1/2" 38.
POWER PS-LR POWER SUPPLY P-5 Operating Modes PS-LR Power Supply The PS-LR is designed to power up to two 3000 LR or 8000 LR exit devices in the following operating modes: • Sequential Mode – A single input switch (dry contact) operates two devices in sequential operation. Ideal for a double-door setup. • Independent Mode – Each LR exit device is controlled by its own input switch. Specifications UL1012 + UL1310 CAN/CSA - C22.2 NO.
P-6 POWER PS-LR POWER SUPPLY All measurements are approximate and are provided for informational purposes only. Refer to the product Installation Instructions. Dimensions 10" 254mm 4-1/8" 104.8mm 9-1/4" 235mm 1-13/64" 30.6mm 10-3/8" 263.5mm Layout & Wiring INPUT #1 N.O. DRY CONTACT SWITCH RATED FOR 15mA PEAK @ 28VDC EXIT DEVICE #2 EXIT DEVICE #1 INPUT #2 N.O. DRY CONTACT SWITCH RATED FOR 15mA PEAK @ 28VDC FIRE ALARM DISABLE N.C.
POWER TRANSFORMER, RECTIFIER AND PIEZO HORN P-7 Transformer, Rectifier and Piezo Horn 4603 Rectifier Converts low voltage AC current to DC of same voltage. Installs in low voltage line between transformer and strike. Full wave bridge type. Rated 2 Amps. (200 PIV). 4605 Transformer Converts 120VAC to 12VAC/24VAC. Rated 40 Volt-amp output assures plenty of power for strike release. 4606 Plug-In Transformer Converts 120VAC current to 24VAC. Plugs into standard wall outlet.
P-8 POWER TRANSFORMER, RECTIFIER AND PIEZO HORN All measurements are approximate and are provided for informational purposes only. Refer to the product Installation Instructions. Dimensions 4606 Plug-In Transformer 2-7/8" 73mm 4603 Rectifier SHRINK TUBING WHITE RED AC RED AC 3-7/8" 98.4mm 4-5/64" 103.6mm MAX - BLACK 1/2" 8" ± 1/2" 12.7mm 203.2mm ± 12.7mm 2-1/4" MAX (4 PLCS) 57.2mm 4605 Transformer 29-0218 Piezo Horn 5/32" 2-21/64" 4mm GREEN BLACK 59.
POWER 4612 POWER TRANSFER DEVICE 4612 Power Transfer Device P-9 Specifications UL634 CONDUIT • Spring steel helix has internal diameter of approximate 5/16”. This provides ample room for multiple wires of the low voltage type used with most electrical hardware. HOUSING • Stamped steel, approximately 1/16” thick. Short (105° swing) version shown is 11-1/12” long. 180° version is 20-5/21” long. Chrome finish.
P-10 POWER 4612 POWER TRANSFER DEVICE All measurements are approximate and are provided for informational purposes only. Refer to the product Installation Instructions. Dimensions Installation 105˚ Swing 1/8" DIA. 3.2mm (2PLCS) M4 SCREW (2PLCS) FRAME DOOR 9/64" DIA. 3.6mm (3 PLCS) 3/4" 19.1mm 7/16" 11.1mm TYP. 15/32" 11.9mm FROM POWER SOURCE 15-7/16" 392.1mm 10-9/32" 261.18mm 3-1/2" 88.9mm 6-3/4" 12-23/32" 21/32" 15/16" 321.5mm 35/64" 13.9mm DIA. TO ELECTRIC HARDWARE 171.
GENERAL INFORMATION TERMS & ICON GLOSSARY GI-1 Terms & Icon Glossary Definitions of commonly used terms plus classifications and descriptions of the icons found throughout this catalog. Terms Glossary Backset: The horizontal dimension from the front of the faceplate to the center of the cylinder. Cam: The part on the back of a cylinder that rotates when the key is turned, and operates the lock mechanism. Deadbolt: A lockbolt having no spring action.
GI-2 TERMS & ICON GLOSSARY ICON GENERAL INFORMATION CLASSIFICATION DESCRIPTION GRADE 2 Passed requirements of 1000 lbs. static force, 50 ft. lbs. of impact force and withstands 300,000 cycles of operation. UL 1034 BURGLARY LISTED Products with a UL 1034 listing are compliant as burglary resistant electric locking mechanisms. UL LISTING UL Listing means that UL has tested representative samples of the product and determined that it meets UL's requirements.
GENERAL INFORMATION ARCHITECTURAL FINISHES GI-3 Architectural Finishes Not all finishes available on all products. For more detailed information on applicable finishes, please refer to the How to Order for each product.
GI-4 GENERAL INFORMATION HANDING OF DOORS Handing of Doors The handing of a door is determined from the outside of the opening. STANDING OUTSIDE THE DOOR: • If the hinges are on the left, it is a left hand door. • If the hinges are on the right, it is a right hand door. • If the door opens away from you, it is a regular bevel door. • If the door opens toward you, it is a reverse bevel door.
GENERAL INFORMATION Adams Rite Limited Warranty Products sold under the Adams Rite brand in the United States of America are warranted free from defects in workmanship and materials under normal use and service.
GI-6 LEED CERTIFICATION GENERAL INFORMATION Other Sustainable Practices LEED Certification Adams Rite receives Silver Level of LEED Certification. Our Sustainability Initiative ASSA ABLOY’s drive to make sustainability an integral part of its business philosophy and culture is apparent in the newly constructed ASSA ABLOY Phoenix building.