Datasheet

ManualsBrandsAdafruit ManualsAdafruitFeather 32u4 with Bluefruit LE and Stacking Headers, Assembled

181

182

183

184

185

186

187

188

189

190

Connection successful

# Scan for primary GATT Services

[D6:4E:06:4F:72:86][LE]> primary

attr handle: 0x0001, end grp handle: 0x0007 uuid: 00001800-0000-1000-8000-00805f9b34fb

attr handle: 0x0008, end grp handle: 0x0008 uuid: 00001801-0000-1000-8000-00805f9b34fb

attr handle: 0x0009, end grp handle: 0x000e uuid: 6e400001-b5a3-f393-e0a9-e50e24dcca9e

attr handle: 0x000f, end grp handle: 0xffff uuid: 0000180a-0000-1000-8000-00805f9b34fb

# Get the handles for the entries in the UART service (handle 0x0009)

[D6:4E:06:4F:72:86][LE]> char-desc

handle: 0x0001, uuid: 00002800-0000-1000-8000-00805f9b34fb

handle: 0x0002, uuid: 00002803-0000-1000-8000-00805f9b34fb

handle: 0x0003, uuid: 00002a00-0000-1000-8000-00805f9b34fb

handle: 0x0004, uuid: 00002803-0000-1000-8000-00805f9b34fb

handle: 0x0005, uuid: 00002a01-0000-1000-8000-00805f9b34fb

handle: 0x0006, uuid: 00002803-0000-1000-8000-00805f9b34fb

handle: 0x0007, uuid: 00002a04-0000-1000-8000-00805f9b34fb

handle: 0x0008, uuid: 00002800-0000-1000-8000-00805f9b34fb

handle: 0x0009, uuid: 00002800-0000-1000-8000-00805f9b34fb

handle: 0x000a, uuid: 00002803-0000-1000-8000-00805f9b34fb

handle: 0x000b, uuid: 6e400002-b5a3-f393-e0a9-e50e24dcca9e

handle: 0x000c, uuid: 00002803-0000-1000-8000-00805f9b34fb

handle: 0x000d, uuid: 6e400003-b5a3-f393-e0a9-e50e24dcca9e

handle: 0x000e, uuid: 00002902-0000-1000-8000-00805f9b34fb

handle: 0x000f, uuid: 00002800-0000-1000-8000-00805f9b34fb

handle: 0x0010, uuid: 00002803-0000-1000-8000-00805f9b34fb

handle: 0x0011, uuid: 00002a27-0000-1000-8000-00805f9b34fb

# 6e400002 (handle 0x000b) = TX characteristic

# 6e400003 (handle 0x000d) = RX characteristic

# Optional (but maybe helpful) ... scan for CCCD entries

[D6:4E:06:4F:72:86][LE]> char-read-uuid 2902

handle: 0x000e value: 00 00

# Enable notifications on the RX characteristic (CCCD handle = 0x000e)

# 0100 = get notifications

# 0200 = get indications

# 0300 = get notifications + indications

# 0000 = disable notifications + indications

[D6:4E:06:4F:72:86][LE]> char-write-req 0x000e 0100

Characteristic value was written successfully

# Just to make sure it was updated

[D6:4E:06:4F:72:86][LE]> char-read-hnd 0x000e

Characteristic value/descriptor: 01 00

# Writing "test" in the Serial Monitor of the Arduino sketch should

# cause this output not that notifications are enabled:

Notification handle = 0x000d value: 74 65 73 74

# Write something to the TX characteristic (handle = 0x000b)

# This should cause E F G H to appear in the Serial Monitor

[D6:4E:06:4F:72:86][LE]> char-write-cmd 0x000b 45

[D6:4E:06:4F:72:86][LE]> char-write-cmd 0x000b 46

[D6:4E:06:4F:72:86][LE]> char-write-cmd 0x000b 47

[D6:4E:06:4F:72:86][LE]> char-write-cmd 0x000b 48

# To send multiple bytes