User manual

HTR-2400 Manual Page 47 Home Theater Setup
HT GLOBAL SETUP P M
CURRENT VOLUME=VOL -29.0 DB
VOLUME PRESET STORED 2
>VOLUME PRESET RECALL 1
TURN ON VOLUME=VOL LASTUSE
MAXIMUM VOLUME=MAX +10.0 DB
FINAL INPUT =FINAL INP 20
INSTALL DEFAULT STORE YES
INSTALL DEFAULT RECALL YES
FACTORY DEFAULT RECALL YES
NEW DSP FIRMWARE UPLOAD YES
V
O
L
U
M
E
Press Volume To Recall
V
O
L
U
M
E
T
u
r
n
T
o
S
e
l
e
c
t
P
r
e
s
e
t
#
T
u
r
n
T
o
S
e
l
e
c
t
F
e
a
t
u
r
e
M
O
D
E
HT GLOBAL SETUP P M
CURRENT VOLUME=VOL -39.0 DB
VOLUME PRESET STORED 2
>VOLUME PRESET RECALLED 3
TURN ON VOLUME=VOL LASTUSE
MAXIMUM VOLUME=MAX +10.0 DB
FINAL INPUT =FINAL INP 20
INSTALL DEFAULT STORE YES
INSTALL DEFAULT RECALL YES
FACTORY DEFAULT RECALL YES
NEW DSP FIRMWARE UPLOAD YES
To test your Volume Pre-
sets by Recalling them,
turn the Mode knob so
that the arrow is on Vol-
ume Preset Recall.
HT GLOBAL SETUP P M
CURRENT VOLUME=VOL -39.0 DB
VOLUME PRESET STORED 2
VOLUME PRESET RECALLED 3
TURN ON VOLUME=VOL RECALL1
>MAXIMUM VOLUME=MAX +10.0 DB
FINAL INPUT =FINAL INP 20
INSTALL DEFAULT STORE YES
INSTALL DEFAULT RECALL YES
FACTORY DEFAULT RECALL YES
NEW DSP FIRMWARE UPLOAD YES
HT GLOBAL SETUP P M
CURRENT VOLUME=VOL -39.0 DB
VOLUME PRESET STORED 2
VOLUME PRESET RECALLED 3
>TURN ON VOLUME=VOL LASTUSE
MAXIMUM VOLUME=MAX +10.0 DB
FINAL INPUT =FINAL INP 20
INSTALL DEFAULT STORE YES
INSTALL DEFAULT RECALL YES
FACTORY DEFAULT RECALL YES
NEW DSP FIRMWARE UPLOAD YES
Turn the Volume knob to select the preset you
wish to recall. Then press the Volume knob.
Repeat this to store up to four Volume Presets.
HT GLOBAL SETUP P M
CURRENT VOLUME=VOL -39.0 DB
VOLUME PRESET STORED 2
VOLUME PRESET RECALLED 3
>TURN ON VOLUME=VOL RECALL1
MAXIMUM VOLUME=MAX +10.0 DB
FINAL INPUT =FINAL INP 20
INSTALL DEFAULT STORE YES
INSTALL DEFAULT RECALL YES
FACTORY DEFAULT RECALL YES
NEW DSP FIRMWARE UPLOAD YES
HT GLOBAL SETUP P M
CURRENT VOLUME=VOL -39.0 DB
VOLUME PRESET STORED 2
VOLUME PRESET RECALLED 3
TURN ON VOLUME=VOL RECALL1
>MAXIMUM VOLUME=MAX +29.5 DB
FINAL INPUT =FINAL INP 20
INSTALL DEFAULT STORE YES
INSTALL DEFAULT RECALL YES
FACTORY DEFAULT RECALL YES
NEW DSP FIRMWARE UPLOAD YES
V
O
L
U
M
E
T
u
r
n
T
o
S
e
l
e
c
t
P
r
e
s
e
t
#
T
u
r
n
T
o
S
e
l
e
c
t
F
e
a
t
u
r
e
M
O
D
E
Turn the Volume knob to
select a turn on level
from one of the four Vol-
ume Presets or the op-
tion of Last Used.
To make certain that the
theater always turns on
at the proper volume
level, turn the Mode
knob until the arrow is on
Turn On Volume.
V
O
L
U
M
E
T
u
r
n
T
o
S
e
l
e
c
t
P
r
e
s
e
t
#
T
u
r
n
T
o
S
e
l
e
c
t
F
e
a
t
u
r
e
M
O
D
E
Turn the Mode knob so
that the arrow is on
Maximum Volume and
then use the Volume
knob to set this level.
To make certain that the
theater’s volume level
never exceeds the point
of distortion, set a Maxi-
mum Volume Level for
the Theater Zone.