Installation manual

Page 67
BRT-1 Baud Rate Translator
The BRT-1 is used when your
Cinema Rhapsody is set to run
at 19200 for control system rea-
sons, yet you also wish to con-
trol the unit via IR. The BRT-1
will upconvert a 1200 Baud IR
signal to 19200 Baud. It does
not down-convert a 19200 sig-
nal to 1200 and as such, will
only permit the Cinema Rhap-
sody to receive commands. It
will not down-convert feedback
to IR. The BRT-1 is a passive
device that connects to an open
ADA Bus port on the ADA Bus
wire harness. It does not re-
quire any additional settings.
BRT-1
1
1
2
2
3
4
3
5
6
4
7
8
5
1
2
6
REC
OSD
78
L
R
L
R
L
R
L
R
AUDIO INPUTS
VIDEO INPUTS
VIDEO OUT
1
2
3
4
DIGITAL AUDIO
INPUTS
AC INPUT
115V~60Hz/230V~50Hz
AC OUTPUT
10A~ Max Switched
ADA Bus¤
1 2 3 4
DATA PORT
Serial Data
12VDC OUT
100mA Max Per
DC 1
1- 2+
DC 2
1- 2+
WARNING! Risk Of Hazardous Energy! Make Proper
Connections.
AVERTISSEMENT! Energie Electrique Dangereuse!
Faire Des Connexions Propres Pour L’Hautparleur.
Voir La Notice De Fonctionnement.
CAUTION: Disconnect Supply Cord Before
Servicing.
ATTENTION: Debrancher Avant Le Depannage.
Use Same
Value Fuse
115V~1AS.B.
230V~.5AS.B.
Voltage
Selector &
Safety Fuse
On This Side
115 V
115V 230V
123
OPTICAL INPUTS
MAIN 2
3
41
S-VIDEO INPUTS
8 CHANNEL DB-25 INPUT
REC
SBL LS
RS
L
R
C
SUBSBR
MAIN
4
G ND O UT I N 12 V DC
L
R
RECORD
OUT
COMPONENT VIDEO
Y
P
B
P R
Y
P
B/B-Y P R/R-Y
Y
P
B/B-Y P R/R-Y
O UTPUT
1
2
3
113
25 14
PIN
POINTS
C INEMA R HAPSODY M ACH II
H
OME T HEATER C ONTROLLER
Lucasfilm Ltd. U.S. patent numbers
5,043,970; 5,189,703; and/or 5,222,059.
European patent number 0323830.
Other U.S. and foreign patents pending.
Lucasfilm and THX are trademarks or
registered trademarks of Lucasfilm Ltd.
Surround EX is a jointly developed
technology of THX and Dolby
Laboratories, Inc., and is a trademark of
Dolby. Used under authorization.
"Dolby", "Pro Logic", & the double-D
Symbol are trademarks of Dolby
Laboratories. All rights reserved.
Manufactured under license from Digital
Theater Systems, Inc. US Pat. No.
5,451,942, 5,956,764, 5,974,380,
5,978,762 and other worldwide patents
issued and pending. "DTS", "DTS-ES
Extended Surround", and "Neo 6" are
trademarks of Digital Theater Systems,
Inc. ' 1996, 2000 Digital Theater
Systems, Inc. All rights reserved.
Manufactured under license from
CAUTION
RISK OF ELECTRIC SHOCK
DO NOT OPEN
ATTENTION!
RISQUE DE CHOC ELECTRIQUE.
NE PAS OUVRIR
MADE IN U.S.A.
ADA NET“
+10dB
PIN +/- CHAN PIN +/- CHAN
1 / 14 LT 7 / 20 SBL
2 / 15 CT 8 / 21 SBR
3 / 16 RT 9 /10/22 SHLD
4 / 17 SB 11 / 23 R.T.A
5 / 18 SL 12 / 24 R.T.B
6 / 19 SR 13 / 25 R.T.C
0dB
MULTI-PIN LFE SUM
1 2 3 4
WH-2000
J1
J2
J3
J4
J5
RJ45
RJ45
RJ45
RJ45
RJ45
RJ45
RJ45
RJ45
WH-2000
Wire
Harness
(Cat. 5)
4 Cond.
18 Gauge
ADA Bus Wire
Cat. 5
Wire
IRR-5000
BRT-1
Baud Rate
Translator
RJ-45 Jacks
BRT-1
Baud Rate Setup
ADA provides two operating speeds (baud rates), either 1200 Baud or 19200 Baud. While 19200
Baud enables faster control and feedback, it will eliminate the ability to control the Cinema Rhapsody
Mach II from being controlled via an infrared (unless you add a BRT-1 Baud Rate Translator to the
system). At 1200 Baud, a 40KHz IR carrier is capable of being attached to the Cinema Rhapsody's
Hex control strings, hence creating an IR command. This command can be learned into most learning
IR remote controls. However, these IR remote controls cannot capture or pass an IR signal with a
baud rate of 19200. The BRT-1 can be added to systems that need to operate at 19200 but it is
important to note that you can opt to run the Cinema Rhapsody Mach II at 1200 baud without compro-
mising system features.
The Out of the Box default is 1200 Baud. To set the Cinema Rhapsody Mach II’s Baud Rate:
1 Turn the Mode knob clockwise until the display’s second line reads SETUP MENU and press
the Mode knob.
2 Turn the Mode knob clockwise until the display’s second line reads PRO SETUP and press the
Mode knob.
3 Turn the Mode knob clockwise until the display’s second line reads NETWORK BAUD and
press the Mode knob.
4 Turn the Mode knob to select between 1200 MODE or 19.2K MODE. Press the Mode knob to
continue with other setups. To completely exit the setup menu, turn the Volume knob.