Installation manual

Page 4
AC Connections
AC Connection
Before you plug your Cinema
Rhapsody into an AC outlet,
make certain that the voltage
selector switch is set to the
proper position. The Cinema
Rhapsody's safety fuse is set
to match the voltage selector’s
setting. There are two voltage
selector switches and two
safety fuse holders. When
viewing the Cinema Rhapsody
from the front, the Main
Switch/Fuse are on the units
left side. The VGA Switch/
Fuse are located on the units
rear panel.
If you are altering the Voltage
Selector Switches, you will
also most likely need to
change the safety fuses.
Before You Begin
As you remove the Cinema Rhapsody Mach II from its packaging,
inspect the condition of the component prior to proceeding with the
following steps for AC connection. In the event that the Cinema
Rhapsody Mach II appears to have suffered cosmetic damage due
to shipping, please contact your Authorized ADA Dealer immedi-
ately and do not proceed to plug the unit into an AC outlet.
Caution
Before plugging your Cinema Rhapsody Mach II into an AC outlet,
check the Voltage Selector Switch settings (the Main Switch and
Fuse holder is located on the units left side when looking at the
Cinema Rhapsody from the front and the VGA Switch and Fuse
holder is located on the units back panel) and make certain that the
selector is set to your appropriate voltage position. For U.S. cus-
tomers, this setting should be 115V. For international customers,
you may need to set this switch to 230V.
Fuse Values
For U.S. customers or international customers also operating on a
115V AC system, the Main fuse value of the Cinema Rhapsody Mach
II should be a 1 Amp Slow Blow fuse. For international customers
operating on a 230V AC system, the Main fuse value should be 1/2
Amp Slow Blow. The safety Main fuse is located next to the Voltage
selector switch on the Cinema Rhapsody's left side (when viewing it
from the front.) The VGA fuse is located on the rear panel. For
systems operating at 115V AC, the fuse value is 2/10 Amp Slow
Blow. For systems operating at 230V AC, the VGA fuse value is
1/10 Amp Slow Blow.
1
1
2
2
3
4
3
5
6
4
7
8
5
1
2
6
REC
OSD
78
L
R
L
R
L
R
L
R
AUDIO INPUTS
VIDEO INPUTS
VIDEO OUT
1
2
3
4
DIGITAL AUDIO
INPUTS
AC INPUT
115V~60Hz/230V~50Hz
AC OUTPUT
10A~ Max Switched
ADA Bus¤
1 2 3 4
DATA PORT
Serial Data
12VDC OUT
100mA Max Per
DC 1
1- 2+
DC 2
1- 2+
WARNING! Risk Of Hazardous Energy! Make Proper
Connections.
AVERTISSEMENT! Energie Electrique Dangereuse!
Faire Des Connexions Propres Pour L’Hautparleur.
Voir La Notice De Fonctionnement.
CAUTION: Disconnect Supply Cord Before
Servicing.
ATTENTION: Debrancher Avant Le Depannage.
Use Same
Value Fuse
115V~1AS.B.
230V~.5AS.B.
Voltage
Selector &
Safety Fuse
On This Side
115 V
115V 230V
123
OPTICAL INPUTS
MAIN 2
3
41
S-VIDEO INPUTS
8 CHANNEL DB-25 INPUT
REC
SBL LS
RS
L
R
C
SUBSBR
MAIN
4
G ND O UT I N 12 V DC
L
R
RECORD
OUT
COMPONENT VIDEO
Y
P
B
P R
Y
P
B/B-Y P R/R-Y
Y
P
B/B-Y P R/R-Y
O UTPUT
1
2
3
113
25 14
PIN
POINTS
C INEMA R HAPSODY M ACH II
H
OME T HEATER C ONTROLLER
Lucasfilm Ltd. U.S. patent numbers
5,043,970; 5,189,703; and/or 5,222,059.
European patent number 0323830.
Other U.S. and foreign patents pending.
Lucasfilm and THX are trademarks or
registered trademarks of Lucasfilm Ltd.
Surround EX is a jointly developed
technology of THX and Dolby
Laboratories, Inc., and is a trademark of
Dolby. Used under authorization.
"Dolby", "Pro Logic", & the double-D
Symbol are trademarks of Dolby
Laboratories. All rights reserved.
Manufactured under license from Digital
Theater Systems, Inc. US Pat. No.
5,451,942, 5,956,764, 5,974,380,
5,978,762 and other worldwide patents
issued and pending. "DTS", "DTS-ES
Extended Surround", and "Neo 6" are
trademarks of Digital Theater Systems,
Inc. ' 1996, 2000 Digital Theater
Systems, Inc. All rights reserved.
Manufactured under license from
CAUTION
RISK OF ELECTRIC SHOCK
DO NOT OPEN
ATTENTION!
RISQUE DE CHOC ELECTRIQUE.
NE PAS OUVRIR
MADE IN U.S.A.
ADA NET“
+10dB
PIN +/- CHAN PIN +/- CHAN
1 / 14 LT 7 / 20 SBL
2 / 15 CT 8 / 21 SBR
3 / 16 RT 9 /10/22 SHLD
4 / 17 SB 11 / 23 R.T.A
5 / 18 SL 12 / 24 R.T.B
6 / 19 SR 13 / 25 R.T.C
0dB
MULTI-PIN LFE SUM
Plug into an AC Outlet
Plug into Cinema Rhapsody
AC Connection
For customers who are using the U.S. standard AC receptacle, you will use the EIC AC Power Cord
provided with the Cinema Rhapsody Mach II. Simply plug this AC cord into an operative AC outlet.
For customers who are using a non-U.S. standard AC receptacle, you will need to acquire an EIC AC
Power Cord with the appropriate receptacle connector. ADA only provides AC Power Cords with the
U.S. standard AC prongs.