QRG 2014 RDX Navigation Online Reference Manual The information and specifications included in this publication were in effect at the time of approval for printing. Honda Motor Co., Ltd., reserves the right, however, to discontinue or change specifications or design at any time without notice and without incurring any obligation. Accessories Precautions The GPS antenna is located in the dashboard. Metallic front or side window tinting can seriously degrade or obstruct GPS reception.
Contents QRG 2014 RDX Quick Reference Guide 2 System Setup P.
QRG Quick Reference Guide - 2014 RDX Overview—Functions at a Glance Navigation You can select any place/landmark as a destination by using voice control or the Interface Dial. The navigation system gives you turn-by-turn driving directions to your destination. Store home addresses (P41) Register 2 home addresses. Store contacts (P37) Store up to 200 contacts in 2 address books. Enter destination (P68) Select your destination using 12 methods.
QRG Audio Quick Reference Guide - 2014 RDX The advanced audio system provides clear, well-defined sound and makes the most of your music. Enjoy listening to a variety of audio sources, such as: FM/AM Radio (P138) XM® Radio (P142) Compact Disc (P147) Hard Disk Drive (HDD) (P151) iPod® (P161) Pandora® (P166) USB Flash Drive (P170) Bluetooth® Audio (P174) AcuraLink® AcuraLink® provides you with important information and messages between your vehicle and Acura.
QRG Quick Reference Guide - 2014 RDX System Controls Navigation Screen Display 1 E (Eject) Button 2 Disc Slot (P6) 3 FM/AM Button (P138) 4 Preset Buttons (P6) 9 VOL 9 (Volume/Power) Knob (P6) la 8 (Sound) Button (P176) 5 CATEGORY Bar (P6) lb DISC Button (P147) 6 TUNE Bar (P6) lc HDD/AUX Button (P151) 7 XM Button (P142) ld AUDIO Button (P7) 8 TITLE Button (P6) le SKIP Bar (P6) lg MAP/GUIDE Button lf SCAN/A.
Voice Control Operation QRG Quick Reference Guide - 2014 RDX a Press and release the d (Talk) button. b Say a voice command. Voice Comand Index (P243) The audio system is muted during voice control mode. Carefully read the usage note for the voice control. Voice Control System (P22) md Microphone d (Talk Button) (P22) me MODE Button (P177) A helpful prompt asks what you would like to do. Press and release the d (Talk) button again to bypass this prompt.
QRG Quick Reference Guide - 2014 RDX Audio System You can play music from a wide array of media sources. You can also control the audio system using voice commands. Basic Operation a Press the VOL 9 (Volume/Power) knob to turn the audio system on or off. Loading a Disc b Select the audio source. c Rotate the VOL 9 (Volume/Power) knob to adjust the volume. a Press the DISC button. b Insert a disc into the disc slot. The disc automatically starts playing.
QRG Audio Control Display Quick Reference Guide - 2014 RDX Press the AUDIO button to display the audio system on the navigation screen.
QRG Quick Reference Guide - 2014 RDX Interface Dial/ENTER Button Operation Rotate dial i You will see these icons in each chapter. They represent how you can operate the Interface Dial.
QRG Quick Reference Guide - 2014 RDX How to Enter Information You can enter information (e.g., city names, street names, personal names, and business names comprising letters, numbers, and symbols) when prompted on input screens by two different methods. Using Voice Control Using the Interface Dial When you see d in this manual, voice commands are available for that feature. Rotate i to highlight a character. Say the letter, number, or symbol (e.g., say d “A”).
QRG Quick Reference Guide - 2014 RDX Map Screen Legend Feature areas Map orientation (P109) North up Heading up Current vehicle position(P110) Park Airport/Business Hospital Shopping Mall Water Area Cemetery Golf Course University GPS signal strength Streets Best reception Good reception No icon: Poor/No reception Freeways State routes Traffic status indicator (P120) Verified streets Unverified streets One-way streets Traffic information available Flow or incident data not available Landmark
QRG Quick Reference Guide - 2014 RDX During Route Guidance During route guidance, route information is displayed on the map screen and guidance screen. Press the MAP/GUIDE button to toggle between the map and guidance screen. Map Screen Map Menu Distance to destination Distance of the actual route. Calculated route (P94) Next guidance indicator Distance to the next guidance point.
QRG Quick Reference Guide - 2014 RDX Navigation—Home Addresses and Going Home The “Home” feature automatically routes you to your home address from any location simply by selecting Go Home 1 or 2, or saying d “Go Home.” You can store two home addresses as Home Address 1 and Home Address 2. (P41) Storing Your Home Address f Enter a name. Going Home a Press the INFO button. a Press the DEST/ROUTE button. b Rotate i to select Set up. Press u. b Rotate i to select Go Home 1. Press u.
QRG Quick Reference Guide - 2014 RDX Navigation—Entering a Destination Enter your destination using one of several methods, then follow route guidance on the map or guidance screen to your destination. You can also perform these steps using d voice control. a Press the DEST/ROUTE button. e Rotate i to select your destination street from the list. Press u. h Rotate i to select OK. Press u. Route guidance to the destination begins. f Enter the street number. Move r to select OK when finished.
QRG Quick Reference Guide - 2014 RDX Navigation—Changing Route or Destination You can alter your route by adding waypoints to visit, adding streets to avoid, or changing your destination during route guidance. Adding a Waypoint (“Pit Stop”) Changing Your Destination You can add up to four waypoints along your route. (P124) There are four methods you can use to specify a new destination during route guidance. b Rotate i to select Waypoint. Press u.
QRG Quick Reference Guide - 2014 RDX AcuraLink® AcuraLink® Messages (P201) AcuraLink® provides a direct communication link between you and Acura. It sends and receives several kinds of messages through XM® Radio, including: AcuraLink Real-Time Traffic™ Displays continuously updated traffic information and recalculates your route in response to traffic flow, incidents, or road closures. (P120) Incident Operating quick tips Weather Construction Diagnostic information Heavy (approx.
QRG Quick Reference Guide - 2014 RDX Troubleshooting Why does the vehicle position icon on the map “lag” a short distance behind my actual position, especially at intersections? This is normal. The navigation system is unaware of the width of intersections. Large differences in vehicle position can indicate a temporary loss of the GPS signal.
QRG Quick Reference Guide - 2014 RDX How to Use This Manual This section explains different methods on how you can easily find information in this manual. Searching the Table of Contents (P1) Contents Two types of Tables of Contents help you find your desired information. More Detailed Contents Table of Contents Chapter Contents First, find the general chapter related to what you are looking for (e.g., entering a destination from the Address Book).
QRG Quick Reference Guide - 2014 RDX After following the menu tree, step-by-step instructions explain how to achieve the desired result. Menu Tree DEST/ROUTE button The menu tree helps guide you through the system’s menu options. To get to your desired function, follow the menu tree in order of the steps shown. NOTE: All menu options can also be activated with voice commands. Press the hard button on the system control panel. Select the menu option with the Interface Dial.
QRG 2014 RDX System Setup This section describes the start-up procedure and the navigation and setup functions. Start-up ................................................... 20 Voice Control System ............................. 22 Command Input .................................... 22 Voice Recognition .................................. 23 Interface Settings ................................... 24 Display and Volume Settings .................. 24 Interface Dial Feedback ..........................
Start-up QRG 2014 RDX System Setup The navigation system starts automatically when you set the power mode to ACCESSORY or ON. At start-up, the following Confirmation screen is displayed. 1. Press u to select OK. Your current position is displayed on the map screen. If you have set any calendar event reminders, they are displayed. Proceed to step 2. 2. Rotate i to select an option. Press u. Your current position is displayed on the map screen.
Start-up QRG ■ Limitations for Manual Operation Disabled option 2014 RDX System Setup Certain manual functions are disabled or inoperable while the vehicle is in motion. You cannot select a grayedout option until the vehicle is stopped. Voice commands are still operable while the vehicle is in motion.
Voice Control System QRG 2014 RDX System Setup Your vehicle has a voice control system that allows hands-free operation of most of the navigation system functions. You can also control the audio and climate control system, and make and receive phone calls using Bluetooth® HandsFreeLink®. The voice control system uses the d (Talk) and K (Back) buttons on the steering wheel and a microphone near the map lights on the ceiling.
Voice Control SystemVoice Recognition QRG 2014 RDX Voice Recognition System Setup To achieve optimum voice recognition when using either the navigation voice control system or Bluetooth® HandsFreeLink®: • Make sure the correct screen is displayed for the voice command that you are using. 2 Voice Commands P. 244 1 Voice Recognition The voice control system can only be used from the driver’s seat because the microphone unit removes noises from the front passenger’s side.
Interface Settings QRG 2014 RDX Display and Volume Settings H INFO button Set up 1 Display and Volume Settings System Setup Use the Main Setup screen to adjust the display and volume. 1. Rotate i to select an item. Press u. 2. Rotate i to make the adjustment. Press u. The following items are available: • Brightness: Adjusts the screen’s brightness. • Contrast: Adjusts the screen’s contrast. • Black Level: Adjusts the screen’s black level. • Volume: Adjusts the navigation system volume level.
Interface SettingsInterface Dial Feedback QRG 2014 RDX Interface Dial Feedback H INFO button Set up Interface Dial Feedback System Setup Set if and when the system reads aloud a selection made using the Interface Dial. Rotate i to select an option. Press u. 1 Interface Dial Feedback You can use this feature to minimize the need to look at the screen while operating the Interface Dial. You can set the interface dial feedback settings using voice commands on the Setup screen.
Interface SettingsBasic Settings QRG 2014 RDX Basic Settings H INFO button Set up Other Basic Settings System Setup Set the map units to either miles or kilometers, and control the voice feedback from the navigation system. Rotate i to select an item. Press u. The following items are available: • Units: Sets the map units to either miles (factory default) or kilometers. • Voice Recognition Tutor: Turns the voice feedback feature on or off.
Interface SettingsColor QRG 2014 RDX Color H INFO button Set up Other Color System Setup Choose the color of the navigation map and system menus. Rotate i to select an item. Press u. The following items are available: • Map Color: Sets the color of the map screen. 2 Map Color P. 28 • Menu Color: Sets the color of the menu screens. 2 Menu Color P.
Interface SettingsColor QRG 2014 RDX ■ Map Color 1 Map Color System Setup H INFO button Set up Other Color Map Color Set separate map colors for Day and Night modes. 1. Rotate i to select Day or Night. Press u. 2. Rotate i to select a color for the map screen. Press u. ■ Menu Color For Night mode Set to BLACK (factory default) to obtain the best nighttime display contrast. 1 Menu Color H INFO button Set up Other Color Menu Color Set separate menu colors for Day and Night modes.
Interface SettingsColor QRG 2014 RDX ■ Switching Display Mode Manually 1 Switching Display Mode Manually System Setup Set the screen brightness separately for Day and Night modes. Press the a (Display mode) button to cycle through the display modes (Day to Night to Off). 1. Press the a button. The Brightness bar is displayed for a few seconds. Rotate i to adjust the brightness. Press u. A visual guide helps you see the difference between Day and Night modes. 2 Day or Night Mode P.
Interface SettingsColor QRG 2014 RDX System Setup Illumination control Priority Operation a button 1 Selects Day, Night, or Off display mode. This button has the highest priority and overrides all other display control adjustments listed below. Remember: Once you press this button, you assume full manual control of the display mode until the power mode is set to VEHICLE OFF (LOCK).
Interface SettingsLanguage QRG 2014 RDX Language H INFO button Set up Other Language System Setup Set the system language used on all screens. You can choose from three languages: English, Français (French), Español (Spanish). Rotate i to select the system language. Press u. 1 Language Voice confirmation of cities and streets only occurs when English is the system language. When Français or Español is selected, some messages continue to be displayed in English.
Interface SettingsWallpapers Setting QRG 2014 RDX Wallpapers Setting H INFO button Set up Other Wallpapers Setting System Setup Select, delete, and import wallpaper pictures for display on the screen. Rotate i to select an item. Press u. The following items are available: • Select wallpaper picture: Sets the desired picture for the wallpaper. 2 Selecting a Wallpaper Picture P. 33 • Delete pictures on HDD: Deletes pictures on the Hard Disc Drive. 2 Deleting Pictures from HDD P.
Interface SettingsWallpapers Setting QRG 2014 RDX ■ Selecting a Wallpaper Picture 1 Selecting a Wallpaper Picture System Setup Two images are provided for the HDD as a factory default. H INFO button Set up Other Wallpapers Setting Select wallpaper picture 1. Rotate i to select a picture. The picture is displayed on the screen. Alternatively, rotate i to select Blank to disable the wallpaper picture setting. 2. Press u to set the wallpaper image.
Interface SettingsWallpapers Setting QRG 2014 RDX ■ Importing Pictures from USB 1 Importing Pictures from USB System Setup H INFO button Set up Other Wallpapers Setting Import pictures from USB You can only import pictures when the vehicle is in Park. 1. Connect a USB flash drive containing pictures. You can connect a USB flash drive using the USB adapter cable in the console compartment. 2 Connecting a USB Flash Drive P. 170 2. Rotate i to select a picture to upload. Press u.
Interface SettingsWallpapers Setting QRG 2014 RDX ■ Deleting Pictures from HDD 1 Deleting Pictures from HDD System Setup H INFO button Set up Other Wallpapers Setting Delete pictures on HDD 1. Rotate i to select a picture. Press u. The picture is displayed on the screen. If there are no pictures on the HDD, “No Entries Exist” is displayed. You can only delete pictures when the vehicle is in Park. You can only delete pictures that have been fully uploaded from a USB flash drive.
Personal Information QRG 2014 RDX H INFO button Set up Personal Information System Setup Use the personal information menu to select and set your address books, home addresses, and PINs. You can also delete unwanted destinations from the list of previously routed destinations. Rotate i to select an item. Press u. The following items are available: • Address Book: Stores new addresses or edits your address book. 2 Address Book P. 37 • Home Address 1: Sets or edits your home address.
Personal InformationAddress Book QRG 2014 RDX Address Book H INFO button Set up Personal Information Address Book 1 Address Book System Setup Store up to 200 address entries in two address books (Driver 1 and Driver 2). You can add, edit, and delete information in the address books. Move r to change the user address book (DRIVER 1 or DRIVER 2). Move w or y to display only the addresses in the selected category. The number of addresses is shared by the two address books.
Personal InformationAddress Book QRG 2014 RDX 2. Rotate i to select an item. Press u. System Setup The following items are available: • Edit Name: Edits the name of the entry. • Edit Address: Edits the address of the entry. • Edit Phone No.: Edits the phone number of the entry. • Edit Category: Specifies the category of the entry. • Delete: Deletes the entry. 3. Rotate i to select Edit Name. Press u. 4. Enter a name or title. Move r to select OK. 5. Rotate i to select Edit Address. Press u. 6.
Personal InformationAddress Book QRG 2014 RDX The following items are available: 1 Adding an Address Book Entry System Setup • Current Position: Select your current location. • Address: Enter an address on the character input screen when prompted. 2 Address P. 70 When you use Place Name or Place Category, the phone number is automatically entered. You can also add a phone number and category. • Previous Destinations: Select a previous destination. 2 Previous Destinations P.
Personal InformationAddress Book QRG 2014 RDX ■ Selecting an Address Book Category System Setup H INFO button Set up Personal Information Address Book 1. Rotate i to select an address. Press u. 2. Rotate i to select Edit Category. Press u. 3. Rotate i to select BUSINESS, PERSONAL, or a category you created. Press u. ■ Creating a New Category 1. Rotate i to select New Category. Press u. 2. Enter a name and select an icon when prompted.
Personal InformationHome Addresses QRG 2014 RDX ■ Deleting an Address Book Entry 1 Deleting an Address Book Entry System Setup H INFO button Set up Personal Information Address Book 1. Rotate i to select the address to delete. Press u. When you transfer the vehicle to a third party, delete all address book entries. 2. Rotate i to select Delete. Press u. 3. Rotate i to select Yes. Press u to delete the address.
Personal InformationPIN Numbers QRG 2014 RDX PIN Numbers H INFO button Set up Personal Information PIN Number System Setup Set a four-digit PIN for protecting personal addresses and your home addresses. Once you set a PIN, you are prompted to enter it whenever you access a personal address or a home address. 1. Rotate i to select the PIN to create. Press u. 2. Rotate i to select a digit to enter. Press u. Repeat to enter a new four-digit PIN. 3.
Personal InformationPrevious Destinations QRG 2014 RDX Previous Destinations H INFO button Set up Personal Information Previous Destinations System Setup The navigation system maintains a list of your previously routed destinations as a shortcut for entering the same destination in the future. You can delete some or all of your previous destinations from the list. 1. Rotate i to select the destination to delete. Press u. Repeat the procedure as necessary.
Music Search Setup QRG 2014 RDX H AUDIO button (in iPod® mode) AUDIO MENU Music Search Setup System Setup Use this feature to set up the music search abilities when using Song By Voice™ (SBV) commands. Rotate i to select an item. Press u The following items are available: • Song By Voice: Turns the feature on or off. 2 Song By Voice™ (SBV) P. 45 • Phonetic Modification: Changes the phonetic (song name, artist name, etc.) so that they are more easily recognized through voice commands.
Music Search SetupSong By Voice™ (SBV) QRG 2014 RDX Song By Voice™ (SBV) H AUDIO button (in iPod® mode) AUDIO MENU Music Search Setup Song By Voice System Setup Use SBV to search for and play music from your HDD or iPod® using voice commands. Use this setting to enable SBV. Rotate i to select an option. Press u. 1 Song By Voice™ (SBV) You can also display the Music Search Setup items in the DISC (music CD) or HDD mode. Select HDD Setup in AUDIO MENU.
Music Search SetupPhonetic Modification QRG 2014 RDX Phonetic Modification H AUDIO button (in iPod® mode) AUDIO MENU Music Search Setup Phonetic Modification System Setup Add phonetic modifications of difficult or foreign words so that it is easier for SBV to recognize artists, songs, albums, and composers in voice commands when searching for music on the HDD or iPod®. 1. Rotate i to select New Modification. Press u.
Music Search SetupPhonetic Modification QRG 2014 RDX 3. Rotate i to select the item to modify (e.g., Artist). Press u. System Setup 4. Rotate i to select an entry (e.g., “No Name”). Press u. 5. Rotate i to select Edit. Press u. Rotate i to select Play to listen to the phonetic modification. Press u. Rotate i to select OK and press u when finished. 6. Enter the phonetic spelling you wish to use (e.g., “Artist A”) when prompted. 7. Move r to select OK to exit.
Routing & Guidance QRG 2014 RDX H INFO button Set up Other Routing & Guidance System Setup Choose various settings that determine the navigation system functionality during route guidance. Rotate i to select an item. Press u. The following items are available: • Rerouting: Sets the route recalculation to automatic or manual mode. 2 Rerouting P. 49 • Unverified Area Routing: Sets whether you use the route guidance in unverified areas. 2 Unverified Area Routing P.
Routing & GuidanceRerouting QRG 2014 RDX System Setup • Street Name Guidance: Sets whether to read out the street names during voice guidance. 2 Street Name Guidance P. 56 Rerouting 1 Rerouting H INFO button Set up Other Routing & Guidance Rerouting Set whether route recalculation occurs automatically or manually during route guidance. Rotate i to select an option. Press u. If you live in an area with poor mapping, you may wish to set Rerouting to MANUAL to avoid constant recalculation.
Routing & GuidanceUnverified Area Routing QRG 2014 RDX Unverified Area Routing H INFO button Set up Other Routing & Guidance Unverified Area Routing System Setup Receive turn-by-turn map and voice guidance in unverified areas. Rotate i to select ON or OFF. Press u. 1 Unverified Area Routing Unverified roads are found in rural areas, and typically include residential streets away from the center of a town. They may not be accurate, and can contain errors in location, naming, and address range.
Routing & GuidanceUnverified Area Routing QRG 2014 RDX Differences OFF ON (factory default) System Setup Guidance (map/voice) There is no turn-by-turn map or voice guidance. Voice guidance commands end with the phrase “if possible” to remind you to verify all traffic restrictions. Directions list A direction list is typically not available. However, depending on your route, directions are provided to help you reach the first available verified road.
Routing & GuidanceTraffic Rerouting QRG 2014 RDX Traffic Rerouting H INFO button Set up Other Routing & Guidance Traffic Rerouting System Setup A faster route can be calculated based on continuously updated traffic information. 2 Traffic Rerouting™ P. 120 Rotate i to select an option. Press u. The following options are available: • ON: The system reroutes automatically based on traffic information. • OFF (factory default): Disables the feature.
Routing & GuidanceEdit Avoid Area QRG 2014 RDX Edit Avoid Area H INFO button Set up Other Routing & Guidance Edit Avoid Area System Setup Specify up to five areas to avoid (e.g., road construction, closures), if possible, when the system calculates routes to your destination. 1. Rotate i to select New Area or an existing area to edit. Press u. 1 Edit Avoid Area The avoid areas are shared with Driver 1 and Driver 2.
Routing & GuidanceEdit Avoid Area QRG 2014 RDX System Setup 5. Rotate i to select a method for specifying the area. Press u. The following options are available: • Address: Specify the general area by entering an address. 2 Address P. 70 • Map Input: Specify the general area by map input. 2 Map Input P. 89 6. If you select Map Input, scroll the map to position the cursor over your desired start point, adjusting the map scale as necessary. Press u to mark the start point.
Routing & GuidanceEdit Waypoint Search Area QRG 2014 RDX Edit Waypoint Search Area H INFO button Set up Other Routing & Guidance Edit Waypoint Search Area System Setup Select the distance from your highlighted route line (on either side of your route) that the system will search for a waypoint. 2 Adding Waypoints P. 124 1 Edit Waypoint Search Area The search distance does not affect the search range used for the Find Nearest voice commands (e.g., say d “Find nearest gas station”).
Routing & GuidanceStreet Name Guidance QRG 2014 RDX Street Name Guidance H INFO button Set up Other Routing & Guidance Street Name Guidance System Setup The navigation system includes the street names during voice guidance (e.g., “Turn right on Main Street”). Rotate i to select an option. Press u. The following options are available: • ON: Voice guidance includes the street names. • OFF (factory default): Disables the feature.
Clock Adjustment QRG 2014 RDX H INFO button Set up Other Clock Adjustment System Setup Set the automatic adjustment of the system clock for daylight saving and international time zones. Rotate i to select an item. Press u. 1 Clock Adjustment You can check the time and date from any screen using voice commands. 2 Global Commands P. 244 Auto Daylight This function is not activated in areas that have not adopted daylight saving time, even if you have set Auto Daylight to ON.
Clock AdjustmentAdjust Time QRG 2014 RDX Adjust Time H INFO button Set up Other Clock Adjustment Adjust Time System Setup Adjust the current time (hours and minutes). 1. Move w or y to select HOUR or MINUTE. 2. Rotate i to adjust the value. 3. Move r to select OK. Resetting the Clock Settings H INFO button Set up Other Clock Adjustment Reset Reset the Auto Daylight and Auto Time Zone settings to the factory defaults.
Vehicle QRG 2014 RDX H INFO button Set up Other Vehicle System Setup Set the off-road tracking feature and correct the vehicle position displayed on the map. Rotate i to select an item. Press u. The following items are available: • Off-road Tracking: Set whether to display the tracking dots on the map. 2 Off-road Tracking P. 60 • Correct Vehicle Position: Adjust the position of the vehicle on the map. 2 Correct Vehicle Position P.
VehicleOff-road Tracking QRG 2014 RDX Off-road Tracking H INFO button Set up Other Vehicle Off-road Tracking System Setup The navigation system can be set to display white off-road tracking dots (“breadcrumbs”) on the map screen whenever you drive into an area approximately 1/2 mile away from a mapped road. Rotate i to select an option. Press u. The following options are available: • ON (factory default): The system displays the white tracking dots. 2 Driving Off-road P.
VehicleCorrect Vehicle Position QRG 2014 RDX Correct Vehicle Position H INFO button Set up Other Vehicle Correct Vehicle Position System Setup Manually adjust the current position of the vehicle as displayed on the map screen if the position appears to be incorrect. 1. Put the vehicle in Park. 2. Rotate i to select Correct Vehicle Position. Press u. 3. Scroll the map to position the arrowhead at your correct position. Press u. 4.
AcuraLink® QRG 2014 RDX AcuraLink/Messages H INFO button Set up Other AcuraLink/Messages System Setup Set the preferences for receiving AcuraLink® messages. 2 AcuraLink® Messages P. 202 Rotate i to select an item. Press u. 1 AcuraLink/Messages For information on setting up the services available through AcuraLink®, visit owners.acura.com. AcuraLink® via XM® Radio is available only in U.S. mainland. Delete Messages Only dealer can delete Diagnostic Info and Recall/ Campaign messages.
Traffic and Weather Status QRG 2014 RDX H INFO button Set up Other Traffic & Weather Status System Setup Confirm the reception status of XM signal, traffic information data, or weather information data. 1 Traffic and Weather Status This item may be grayed out when your vehicle is in Alaska, Hawaii, Canada, Puerto Rico, and Mexico because XM® Radio or traffic/weather information is not available.
Data Reset QRG 2014 RDX Reset Factory Default Settings H INFO button Set up Other Reset Factory Default System Setup Reset all the settings on the Setup screens and multi-view rear camera brightness settings to their factory default. Rotate i to select Yes. Press u to reset the settings. 1 Reset Factory Default Settings When you transfer the vehicle to a third party, reset all settings to default and delete all personal data.
Data ResetClear Personal Data QRG 2014 RDX Clear Personal Data H INFO button Set up Other Clear Personal Data System Setup Delete uploaded data, calendar entries, address books, or stored destinations, or reset other settings to their factory defaults. 1. Rotate i to select an item. Press u. Repeat the procedure to delete other items. Items to be deleted are indicated with a trash icon. 2. Move r to select OK. 3. Rotate i to select Yes. Press u to delete the data.
QRG 66 2014 RDX
QRG 2014 RDX Navigation This section describes how to enter a destination, select a route to take, and follow the route to your destination. It also describes how to change your route or destination along the way. Entering a Destination ........................... 68 Address ................................................. 70 Address Book......................................... 75 Previous Destinations ............................. 76 Place Name ............................................
Entering a Destination QRG 2014 RDX H DEST/ROUTE button 1 Entering a Destination This section describes how to enter a destination for route guidance. Rotate i to select an item. Press u. Navigation Move y to select Dest. MENU 2 to display additional menu entries. Navigation” If you press the DEST/ROUTE button when en route, the Route Menu screen is displayed. 2 Changing Your Route P. 122 Prior to departure, you can set areas along your route to avoid. 2 Avoiding Streets P.
Entering a Destination QRG 2014 RDX • Place Name: Sets a destination by entering a place name. 2 Place Name P. 77 • Place Category: Sets a destination by selecting a place/landmark. 2 Place Category P. 80 Navigation • Place Phone No.: Sets a destination by entering the phone number of a place/ landmark. 2 Place Phone Number P. 84 • ZAGAT: Sets a destination (restaurant) by using ZAGAT® SURVEY Rating information. 2 ZAGAT P. 84 • Coordinate: Sets a destination by entering latitude and longitude.
Entering a DestinationAddress QRG 2014 RDX Address H DEST/ROUTE button Address Enter an address to use as the destination. The state or province you are currently in is displayed (e.g., California). Navigation Rotate i to select an item. Press u. The following items are available: • City: Selects your destination city. 2 Selecting a City P. 72 • Street: Selects your destination street. 2 Selecting a Street P. 73 • Change State: Selects the state or province. 2 Selecting the State or Province P.
Entering a DestinationAddress QRG 2014 RDX ■ Selecting the State or Province 1 Selecting the State or Province Move w or y to select the following areas: H DEST/ROUTE button Address Change State Navigation Rotate i to select a state from the list. Press u. ■ Selecting a City by Zip Code • USA for the U.S.
Entering a DestinationAddress QRG 2014 RDX 3. Rotate i to select the destination city from the list. Press u. Navigation Next, you are prompted to enter a street name. 2 Selecting a Street P. 73 1 Selecting a City Vehicle position may not be displayed when: • The automobile is traveling off-road. • The vehicle position data cannot be updated. You do not need to enter spaces or symbols (e.g., &, -, %). Partial matches are supported (e.g., “ANGELES” to find “LOS ANGELES”).
Entering a DestinationAddress QRG 2014 RDX 2. Rotate i to select your destination city from the list. Press u. Navigation A list of matching hits is automatically displayed after you enter several letters, with the closest match at the top of the list. Matching letters are in yellow. Non-detailed area mark: Try entering the street first and then select the city. Next, you are prompted to enter a street name. 2 Selecting a Street P.
Entering a DestinationAddress QRG 2014 RDX 2. Rotate i to select your destination street from the list. Press u. Navigation A list of matching hits is automatically displayed after you enter several letters, with the closest match at the top of the list. Matching letters are in yellow. 1 Selecting a Street If you did not select a city first and there is more than one city with the specified street, a list of cities is displayed. 3. Enter the street number. Move r to select OK.
Entering a DestinationAddress Book QRG 2014 RDX Address Book H DEST/ROUTE button Address Book 1 Address Book Select an address stored in your address book to use as the destination. Navigation 1. Rotate i to select your destination from the list. Press u. 2. Set the route to your destination. 2 Calculating the Route P. 91 Move w or y to display only the entries in a category: ALL, BUSINESS, PERSONAL, or other categories you have created.
Entering a DestinationPrevious Destinations QRG 2014 RDX Previous Destinations H DEST/ROUTE button Previous Destinations Select an address from a list of your 50 most recent destinations to use as the destination. The list is displayed with the most recent destination at the top. Navigation 76 1 Previous Destinations If Previous Destinations is grayed out, there are no previous destinations entered. 1. Rotate i to select a destination from the list. Press u.
Entering a DestinationPlace Name QRG 2014 RDX Place Name H DEST/ROUTE button Place Name 1 Place Name Enter the name of a place (e.g., business, hotel, restaurant) stored in the map database to use as the destination. Navigation 1. Enter a place name. 2. Move r to select LIST to display a list of matching hits. 3. Rotate i to select a place name from the list. Press u. This option is convenient if you know the exact name of a place.
Entering a DestinationPlace Name QRG 2014 RDX ■ Place Name in Multiple Categories If the place name is in multiple categories in the map database, the following screen is displayed. Navigation 1. Rotate i to select a place name. Press u. 2. Rotate i to select a subcategory. Press u. 78 1 Place Name in Multiple Categories Move r to select SORT BY CITY or SORT BY DISTANCE. Matching letters are in yellow.
Entering a DestinationPlace Name QRG 2014 RDX 3. Rotate i to select a place. Press u. 4. Set the route to your destination. 2 Calculating the Route P.
Entering a DestinationPlace Category QRG 2014 RDX Place Category H DEST/ROUTE button Place Category 1 Place Category Select the category of a place (e.g., Banking, Lodging, Restaurant) stored in the map database to search for the destination. Navigation 1. Rotate i to select a category. Press u. This option is convenient if you do not know the exact name of a place or if you want to narrow down the number of matches returned for places with a common name.
Entering a DestinationPlace Category QRG 2014 RDX 3. Rotate i to select an item. Press u. 1 Place Category Navigation Sort by Distance to Travel For locations sorted by distance to travel, you can move r to select MORE to increase the scope of the search. The number of locations increases to 100, 200, and up to 1000. When the number of locations is 100 or less, you can increase the scope to 500 miles, 1000 miles, or the entire U.S.
Entering a DestinationPlace Category QRG 2014 RDX 4. Rotate i to select a place name from the list. Press u. 5. Set the route to your destination. 2 Calculating the Route P. 91 Navigation ■ My Favorites H DEST/ROUTE button Place Category My Favorites Store up to 30 favorite subcategories. 82 1 Place Category The straight line distance (as the crow flies, not driving distance) and direction to the destination are shown for the highlighted place. Restaurants with a z icon have a ZAGAT® review.
Entering a DestinationPlace Category QRG 2014 RDX ■ To store a subcategory in favorites: 1 My Favorites 1. Rotate i to select a subcategory on any subcategory screen. Navigation 2. Move r to select ADD TO MY FAVORITES. Stored categories A subcategory stored in My Favorites has a star at the end of the line. Deleting categories You can also delete a favorite subcategory on any Subcategory screen.
Entering a DestinationPlace Phone Number QRG 2014 RDX Place Phone Number H DEST/ROUTE button Dest. MENU 2 Place Phone No. Select a destination by phone number. Only phone numbers in the database are recognized. Navigation 1. Enter the area code and phone number. Move r to select OK. 2. Set the route to your destination. 2 Calculating the Route P. 91 ZAGAT H DEST/ROUTE button Dest. MENU 2 ZAGAT Find a restaurant by ZAGAT® SURVEY Rating information. 1. Rotate i to select an item. Press u .
Entering a DestinationZAGAT QRG 2014 RDX 1 ZAGAT® The following items are available: • Place Name: Searches for a place in the subcategory by name. Enter a city name when prompted. Navigation • City Vicinity: Searches for a place in the subcategory within a 20-mile radius of a specific city. Enter a city name and then a place name when prompted. Only the first 1000 matching places/landmarks are displayed.
Entering a DestinationZAGAT QRG 2014 RDX ■ Finding Restaurants by ZAGAT Rating H DEST/ROUTE button Dest. MENU 2 ZAGAT Sort by ZAGAT Rating Navigation 1. Rotate i to select the sort method used to list the restaurants. Press u. The following options are available: • Food, Décor, Service: Lists the restaurants by the rating value. • Cost: Lists the restaurants by the average cost of a meal (including drink and tip). 2. Rotate i to select a restaurant. Press u. 3.
Entering a DestinationCoordinate QRG 2014 RDX Coordinate H DEST/ROUTE button Dest. MENU 2 Coordinate Specify a location using latitude and longitude map coordinates. Navigation 1. Enter the latitude. Move r to select OK. 2. Enter the longitude. Move r to select OK. 3. Scroll the map to position the cursor over your desired destination, adjusting the map scale as necessary. Press u. 1 Coordinate Latitude and longitude must be entered up to the seconds’ value.
Entering a DestinationIntersection QRG 2014 RDX Intersection H DEST/ROUTE button Dest. MENU 2 Intersection Select the intersection of two streets as the destination. The state or province for your current location is displayed at the top of the screen (e.g., California). Navigation 1. Rotate i to select the intersection search method. Press u. 2. Set the route to your destination. 2 Calculating the Route P. 91 The following options are available: • Street: Selects the two intersecting streets.
Entering a DestinationMap Input QRG 2014 RDX Map Input H DEST/ROUTE button Dest. MENU 2 Map Input Use the Interface Dial to manually select an icon or a location on the map screen as the destination. Navigation You are prompted to define the map area to display. 1. Rotate i to select an item. Press u. The following items are available: • Current Position: Your current location is centered on the map. • City: You are prompted to select the city. 2 Selecting a City P.
Entering a DestinationMap Input QRG 2014 RDX 2. Scroll the map to position the cursor over your desired destination, adjusting the map scale as necessary. Press u. Navigation If the address is not the desired location, scroll the map to another location and try again. 3. Press u again to display the route calculation menu. 2 Calculating the Route P. 91 4. Rotate i to select Set as Dest. Press u.
Calculating the Route QRG 2014 RDX This section describes how to calculate your route. 1. Rotate i to select OK. Press u. Navigation The system calculates and displays the route line on the map screen. 2 Route Line P. 95 1 Calculating the Route The current route preferences are displayed as icons on the top right of the Calculate Route screen. The straight line distance (as the crow flies, not driving distance) and direction to the destination are shown together with weather information.
Calculating the RouteChanging the Route Preference QRG 2014 RDX Changing the Route Preference Change the route preference by selecting minimum or maximum driving methods. 1. Rotate i to select an item. Press u. Navigation 2. Rotate i to select MIN or MAX. Press u. Repeat step 1 and 2 as necessary. 3. More r to select OK. Viewing the Routes The calculated route may be the shortest route or the route you would choose.
Calculating the RouteCalculating the Route on the Destination Map QRG Calculating the Route on the Destination Map Calculate the route from the map of the destination address. Rotate i to select Calculate Route. Press u. 2014 RDX 1 Calculating the Route on the Destination Map d “Display Destination Map” (when en route) Navigation The system calculates and displays the route line on the map screen. 2 Route Line P.
Driving to Your Destination QRG 2014 RDX This section describes how to follow the route guidance to your destination, receive traffic and weather information and choose the icons displayed on the map screen. 1 Viewing the Route Viewing the Route d “Display Map” Navigation ■ Map Screen After calculating the route to your destination, the route is displayed on the map screen. 2 Map Screen Legend P.
Driving to Your DestinationViewing the Route QRG 2014 RDX ■ Guidance Screen 1 Guidance Screen The guidance screen offers an alternative way to view your route. Navigation • In single-screen mode, press the MAP/GUIDE button to switch between the map and guidance screens. A visual guide helps you check the guidance screen. 2 Guidance Screen P. 11 • In split-screen mode, press the MAP/GUIDE button to switch between the next guidance direction and a list of guidance directions.
Driving to Your DestinationViewing the Route QRG 2014 RDX Blue-pink route line • If Unverified Area Routing is ON, the route line changes to a dashed blue-pink line to indicate that the route line uses unverified streets. Navigation ■ Deviating From the Planned Route If you leave the calculated route, the system automatically recalculates a route to the desired destination based on your current location and direction. 2 Rerouting P.
Driving to Your DestinationViewing the Route QRG 2014 RDX ■ Driving Off-road Navigation If you leave all mapped (digitized) roads, the system automatically starts displaying a series of dots (breadcrumbs) to track the path you are taking. If needed, you can follow the dots back to the mapped road you originally left. 2 Off-road Tracking P. 60 1 Driving Off-road A message “Not on a digitized road” may appear when you drive half a mile away from a mapped road.
Driving to Your DestinationListening to Voice Guidance QRG 2014 RDX Listening to Voice Guidance H ENTER button (on map) Voice As you approach each guidance point, a pop-up window is displayed on the map screen with instructions for you to follow. Voice guidance for each guidance point is also provided.
Map Menu QRG 2014 RDX Displaying the Map Menu Use the Map Menu to control the icons displayed on the screen and to display traffic information, weather information, and messages. You can also use the Map Menu to find locations or to cancel the route. Navigation 1. On the map screen, press u to select MAP MENU (if displayed). The Map Menu is displayed on the map screen. 2. Rotate i to select an item. Press u.
Map MenuDisplaying the Map Menu QRG 2014 RDX • Traffic Incidents: Displays a list of the traffic incidents around your current location or on your current route. 2 Traffic Rerouting™ P. 120 Navigation • Weather Info: Allows you to view the weather forecast, warning list, warning map, and radar image map. 2 Weather Information P. 115 • Guidance Menu: Allows you to set or confirm the guidance points and freeway exits for your route. 2 Guidance Menu P.
Map MenuGuidance Menu QRG 2014 RDX Guidance Menu H ENTER button (on map) Guidance Menu Display the guidance points and freeway exits for your route, and set the display mode for the map and guidance screens. Navigation Rotate i to select an item. Press u. The following items are available: • Directions: Displays a list of the guidance points. 2 Directions P. 102 • Exit Info: Displays a list of the freeway exits. 2 Freeway Exit Information P. 103 • Guidance Mode: Selects the guidance display mode.
Map MenuGuidance Menu QRG 2014 RDX ■ Directions 1 Directions H ENTER button (on map) Guidance Menu Directions Display a list of the guidance points on your route for your confirmation. Navigation 1. Rotate i to select a guidance point from the list. Press u. The system displays a map of the guidance point. 2. Press u to select RETURN or press the CANCEL button to return to the previous screen. 102 Guidance points with exit information are indicated by a (freeway exit information) icon.
Map MenuGuidance Menu QRG 2014 RDX ■ Freeway Exit Information 1 Freeway Exit Information Navigation H ENTER button (on map) Guidance Menu Exit Info d “Display Freeway Exit Information” Display a list of the freeway exits for the route. You can view freeway exit information (whether the exit is near gas stations, restaurants, ATMs, etc.) and add new destinations or waypoints to the calculated route.
Map MenuGuidance Menu QRG 2014 RDX ■ Guidance Mode 1 Guidance Mode H ENTER button (on map) Guidance Menu Guidance Mode Navigation Select the display mode during route guidance: single-screen mode (default) or splitscreen mode. Rotate i to select an option. Press u. The following options are available: • Single Screen: Displays the map and guidance screens on separate screens.
Map MenuGuidance Menu QRG 2014 RDX • Split Screen: Displays the map and guidance information simultaneously on the map screen. Navigation Press the MAP/GUIDE button Next guidance point 1 Guidance Mode Next guidance point The next guidance point (the pop-up window) is displayed on the map screen as you approach a guidance point in the single-screen mode.
Map MenuMap Information QRG 2014 RDX Map Information H ENTER button (on map) Map Information Select the landmark icons to display on the map, change the orientation of the map, display your current location, and learn the meaning of the icons, colors, and symbols displayed on the map. Navigation Rotate i to select an item. Press u. The following items are available: • Show Icon on Map: Selects the icons to display on the map. 2 Showing Icons on the Map P.
Map MenuMap Information QRG 2014 RDX ■ Showing Icons on the Map 1 Showing Icons on the Map H ENTER button (on map) Map Information Show Icon on Map Navigation The icon bar along the bottom of the screen allows you to select the icons that are displayed on the map. You can display or hide the icons using voice commands on the map screen (e.g., say d “Display hospital”). 2 Map Display Commands P. 244 Rotate i to select an icon in the icon bar. Press u.
Map MenuMap Information QRG 2014 RDX ■ Fine-tuning the Icons 1 Fine-tuning the Icons Icons in some categories can be fine-tuned to display or hide. Navigation 1. Rotate i to select an icon category from the list (e.g., Other Icons). Press u. 2. Rotate i to select the icons to display on the map. Press u. Pressing u toggles the icon display on or off. Repeat the procedure as necessary. 3. Move r to select OK. 108 To display the “Other Icons,” be sure to turn on OTHER ICON in the icon bar.
Map MenuMap Information QRG 2014 RDX ■ Map Orientation 1 Map Orientation d “Display Heading-up” (on map screen), d “Display North-up” (on map screen) Select the map orientation. The red arrow in the symbol always points North. On scales greater than 1 mile, North-up mode is always used. Navigation H ENTER button (on map) Map Information Rotate i to select North-up or Heading-up. Press u. The system changes the map orientation and displays the map screen.
Map MenuMap Information QRG 2014 RDX ■ Current Location 1 Current Location H ENTER button (on map) Map Information Current Location Navigation Display and save your current location for future use as a destination. The address, latitude, longitude, and elevation of your current location are displayed. ■ To save your current location in the address book: 1. Rotate i to select Save. Press u.
Map MenuMap Information QRG 2014 RDX ■ Map Legend 1 Map Legend H ENTER button (on map) Map Information Map Legend Navigation See an overview of the map lines, areas, routes, traffic information, navigation icons, and weather icons. A visual guide helps you see the map legend. 2 Map Screen Legend P. 10 2 AcuraLink Real-Time Traffic™ P. 15 2 AcuraLink Real-Time Weather™ P. 15 Rotate to i select an item. The system displays the map legend.
Map MenuMap Information QRG 2014 RDX ■ Map Scale and Functions 1 Map Scale and Functions You can change the map scale using voice commands on the map screen (e.g., say d “Display 2 mile scale”). 2 Map Scale Commands P. 245 The functions that are available from the map screen depend on the map scale. Map Scale (top: mile, bottom: metric) Navigation Function page 1/20 1/8 80 1/4 1/2 1 200 400 800 1.
Map MenuMap Information QRG 2014 RDX ■ Map Icons and Functions 1 Map Icons and Functions Display or hide all icons on the map screen, with the exception of Honda/Acura Dealer icons which are always shown.
Map MenuMap Information QRG 2014 RDX ■ Traffic icon 1 Traffic Incident Icon display control Icon selectable Traffic speed Yes No No Traffic incident Yes No Yes Icon display control Icon selectable Icon searchable Yes No No Type Navigation ■ Weather icon Type Weather info. 114 Icon searchable When you use the Interface Dial to position the cursor (round red circle) over the traffic incident icon, you can view the summary of the incident.
Map MenuWeather Information QRG 2014 RDX Weather Information H ENTER button (on map) Weather Info 1 Weather Information View the weather forecast, warning list, warning map, and radar image map. Rotate i to select an item. Press u. This feature requires an AcuraLink Real-Time Weather™ subscription. 2 Subscribing to XM® Radio P. 146 Navigation You can also display the weather information menu from the INFO screen. Press the INFO button. Rotate i to select Weather Info and press u.
Map MenuWeather Information QRG 2014 RDX ■ Weather Forecast 1 Weather Forecast H ENTER button (on map) Weather Info Weather Forecast View the weather forecast for your current position or a city you select. Navigation 1. Rotate i to select an item. Press u. The following items are available: • City Vicinity: Displays the weather forecast for the selected city. You are prompted to select the city. 2 Selecting a City P.
Map MenuWeather Information QRG 2014 RDX ■ Warning List 1 Warning List H ENTER button (on map) Weather Info Warning List Sorted by Distance View a list of all weather warnings for a given location or route (U.S. only). Navigation 1. Rotate i to select a warning. Press u. Move w or y to select All US, Within 500mi, or On Route to specify the warnings to display. A warning icon in the list indicates that your vehicle is in the warning area or that the calculated route runs through the area.
Map MenuWeather Information QRG 2014 RDX ■ Warning Map 1 Warning Map Navigation H ENTER button (on map) Weather Info Warning Map You can change the map scale to 15, 50, or 150 miles. View a color-coded weather warning map. Each color corresponds to a different type of warning. You can also say d “Read List” to listen to the weather warning information. 1. Scroll the map to position the cursor over a colored area, adjusting the map scale as necessary. Press u to select WEATHER DETAIL.
Map MenuWeather Information QRG 2014 RDX ■ Radar Map 1 Radar Map Navigation H ENTER button (on map) Weather Info Radar Map You can change the map scale to 50, 150, or 350 miles. View a weather radar image map displaying rain and snow systems. A visual guide helps you see a weather radar image map. 2 AcuraLink Real-Time Weather™ P. 15 Scroll the map to view weather information, adjusting the map scale as necessary.
Map MenuTraffic Rerouting™ QRG 2014 RDX Traffic Rerouting™ When driving to your destination, the system automatically searches for a faster route based on traffic flow information and traffic incidents. 2 AcuraLink Real-Time Traffic™ P. 15 2 Traffic Rerouting P. 52 1 Traffic Rerouting This feature requires an AcuraLink Real-Time Traffic™ subscription. 2 Subscribing to XM® Radio P.
Map MenuTraffic Rerouting™ QRG 2014 RDX 2. Press u to select TRAFFIC DETAIL. 1 Traffic Rerouting™ Manually You can choose to avoid up to 10 traffic incidents. It is not always possible for the system to calculate a route that avoids all traffic incidents or specific traffic incidents you select. Navigation The “On Route” tab on the Traffic List screen is only available during route guidance. 3. Rotate i to select Avoid. Press u. Repeat step 1 to 3 as necessary.
Changing Your Route QRG 2014 RDX H DEST/ROUTE button (when en route) 1 Changing Your Route This section describes how to alter your route, add an interim “waypoint” (pit stop), choose a different destination, cancel your current destination, and continue your trip after stopping. Navigation Rotate i to select an item. Press u. The following items are available: • Cancel Route: Cancels the route guidance. 2 Canceling the Route P. 123 • Detour: Calculates a detour route. 2 Taking a Detour P.
Changing Your RouteCanceling the Route QRG 2014 RDX Canceling the Route H DEST/ROUTE button (when en route) Cancel Route 1 Canceling the Route Cancel the route guidance and remove the destination and all waypoints from the destination list. The system then returns to the map screen. Navigation Taking a Detour You can also cancel your route from the Map Menu. 2 Map Menu P. 99 1 Taking a Detour H DEST/ROUTE button (when en route) Detour Calculate a detour route manually.
Changing Your RouteAdding Waypoints QRG 2014 RDX 2. Move r to select OK. The system calculates a new route. Navigation Adding Waypoints 1 Adding Waypoints Add up to four waypoints (pit stops) along the route to your destination. Waypoints are displayed on the map screen as small, numbered red flags. The route follows the waypoints in the order they are listed in the Destination List. Waypoints allow you to stop for gas or food, for example, and then continue on to your destination.
Changing Your RouteAdding Waypoints QRG 2014 RDX ■ Adding Waypoints from the Route Menu 1 Adding Waypoints H DEST/ROUTE button (when en route) Waypoint Search method Navigation 1. Rotate i to select a search method to add a waypoint. Press u. “Search around” method “Search along” method The following options are available: • SEARCH AROUND: Searches in a spiral pattern around the location you select. • SEARCH ALONG: Searches within a “corridor” on either side of the locations you select. 2.
Changing Your RouteAdding Waypoints QRG 2014 RDX 3. Rotate i to select a place. Press u. The waypoint is added to the Destination List. Navigation 4. Move r to select OK. The route is automatically recalculated and displayed on the map screen.
Changing Your RouteAdding Waypoints QRG 2014 RDX ■ Adding Waypoints from the Calculate Route Screen 1. Rotate i to select ADD TO Dest. List. Press u. Navigation 2. Rotate i to select a location in the Destination List. Press u. 3. Move r to select OK. The route is automatically recalculated and displayed on the map screen.
Changing Your RouteEditing the Destination List QRG 2014 RDX Editing the Destination List H DEST/ROUTE button (when en route) Destination Lists Delete or edit the order of waypoints. 1. Move y to select Edit. Navigation Move w to select Map to display the destination and waypoints on the map screen. 2. Rotate i to select an item. Press u. 3. Move r to select OK. The route is automatically recalculated and displayed on the map screen.
Changing Your Destination QRG 2014 RDX There are several methods you can use to change the route destination. Find Nearest Place 1 Find Nearest Place Navigation H ENTER button (on map) Find Nearest… d “Find Nearest…” (on map screen) Search for the nearest place/landmark on the map screen and set it as your destination. The Find Nearest voice command is the fastest method of specifying a place/landmark as your destination. Many kinds of places can be found. 2 Find Place Commands P. 245 1.
Changing Your DestinationSelecting a Destination on the Map QRG 2014 RDX Selecting a Destination on the Map Select a new destination when en route by selecting a location on the map. Navigation 1. Scroll the map to position the cursor over your desired destination, adjusting the map scale as necessary. Press u. 1 Selecting a Destination on the Map If there is more than one icon or street under the map cursor, you are prompted to select the item from a list.
Changing Your DestinationEntering a New Destination QRG 2014 RDX 3. Rotate i to select an option. Press u. Navigation The route is automatically recalculated and displayed on the map screen. The following options are available: • New Dest.: Sets the location as your new destination. • Waypoint: Sets the location as a new waypoint. Entering a New Destination 1 Entering a New Destination H DEST/ROUTE button (when en route) Dest. MENU 1 or Dest.
Changing Your DestinationEntering a New Destination QRG 2014 RDX 3. Rotate i to select an option. Press u. Navigation The route is automatically recalculated and displayed on the map screen. The following options are available: • New Dest.: Sets the location as your new destination. • Waypoint: Sets the location as a new waypoint.
Resuming Your Trip QRG 2014 RDX Stop your vehicle en route (e.g., to rest, stop for gas, etc.), and then continue on your route. Navigation If you did not complete your route, the Continue Trip screen is displayed when you restart your vehicle. Rotate i to select OK. Press u. You can continue on the same route. 1 Resuming Your Trip The Continue Trip screen has the same options as when you calculate a route. 2 Calculating the Route P. 91 To cancel your destination, press the CANCEL button.
QRG 134 2014 RDX
QRG 2014 RDX Audio This section describes how to operate the audio system. You can play music from a wide array of media sources, and control the audio system using the audio buttons, the Interface Dial, or voice control. Audio System .................................................. 136 About Your Audio System.............................. 136 Auxiliary Input Jack ........................................ 136 System Theft Protection ................................. 137 Playing FM/AM Radio .............
Audio System QRG 2014 RDX About Your Audio System The audio system features FM/AM radio and XM® Radio. It can also play audio discs, WMA/MP3/AAC tracks, iPod®, USB flash drives, and Bluetooth® devices. The audio system is operable from the buttons and switches on the panel, or the remote controls on the steering wheel. 2 Audio Remote Controls P. 177 2 Audio System P. 6 1 About Your Audio System You can operate the audio system by voice commands. 2 Audio Commands P.
Audio SystemSystem Theft Protection QRG 2014 RDX System Theft Protection The system is disabled when it is disconnected from the power source, such as when the battery is disconnected or goes dead. ■ Reactivating the System 1. Set the power mode to ON, and turn on the system. If you set the power mode to ACCESSORY, you will be requested to enter the security code. See step 3. Audio 2. Press and hold the VOL 9 (Volume/Power) button again for more than two seconds.
Playing FM/AM Radio QRG 2014 RDX Selecting FM/AM Mode 1 Playing FM/AM Radio 1. Press the FM/AM button. Press the FM/AM button again, if necessary, to select the frequency band (AM, FM1, FM2). 2. Select a station using the Preset buttons and the bars (SKIP, TUNE, SCAN/A.SEL) On the FM bands, you can also use the CATEGORY bar and TITLE button to select a station provided by the Radio Data System (RDS). Audio The band and frequency are displayed on the display.
Playing FM/AM RadioAudio Menu QRG 2014 RDX Audio Menu H AUDIO button (in FM/AM mode) AUDIO MENU Rotate i to select an item. Press u. 1 Audio Menu The A.SEL indicator comes on the display when A.Sel is ON. If you do not like the stations Auto Select has stored, you can change the frequencies stored in the preset buttons manually. Set A.Sel to OFF to restore the previous preset button settings. Audio The following items are available: • Sound Setup: Displays the sound preferences screen.
Playing FM/AM RadioRadio Data System (RDS) QRG 2014 RDX Radio Data System (RDS) Provides text data information related to your selected RDS capable FM station. ■ RDS Info Display Press the TITLE button to turn RDS information on or off. When set to ON, the name of the FM station is displayed on the display. When set to OFF, the frequency of the station is displayed.
Playing FM/AM RadioRadio Data System (RDS) QRG 2014 RDX ■ Radio Text Display H AUDIO button (in FM/AM mode) AUDIO MENU Read Radio Text 1 Radio Text Display The RDS indicator comes on the display when the selected RDS station is broadcasting text data. Display the radio text information of the selected RDS station.
Playing XM® Radio QRG 2014 RDX Selecting XM Mode 1 Playing XM® Radio 1. Press the XM button. Press the XM button again, if necessary, to select the channel band (XM1, XM2). 2. Select a channel using the Preset buttons and the bars (SKIP, TUNE, CATEGORY, SCAN/A.SEL) The band and channel are displayed. Audio Audio Screen Control H AUDIO button (in XM mode) Control the audio system through the navigation screen. Channel band 1. Move e to select the channel band (XM1, XM2). 2.
Playing XM® RadioAudio Menu QRG 2014 RDX Audio Menu H AUDIO button (in XM mode) AUDIO MENU Rotate i to select an item. Press u. Audio The following items are available: • Sound Setup: Displays the sound preferences screen. 2 Adjusting the Sound P. 176 • Mode: Sets CH (channel mode) or CAT (category mode) scan mode. • Note: Displays a list of stored audio samples. 2 Note Function P. 144 • Channel List: Displays the list of available channels. Scroll the list to select a channel.
Playing XM® RadioNote Function QRG 2014 RDX Note Function Record a 10-second sound file from the current channel that contains the channel, category, name, and title information. ■ Recording a Sound File 1. When tuned to the channel you want to record, press and hold the XM button for a few seconds to start recording. Audio 2. Press the XM button again to stop the recording if less than 10 seconds have elapsed.
Playing XM® RadioNote Function QRG 2014 RDX ■ Deleting a Sound File H AUDIO button (in XM mode) AUDIO MENU Note 1. Rotate i to select a sound file. To delete all files, proceed to step 2. Audio 2. Move w or y to select DELETE ALL or DELETE. 3. Rotate i to select Yes. Press u.
Playing XM® RadioXM® Radio Service QRG 2014 RDX XM® Radio Service ■ Subscribing to XM® Radio 1 Subscribing to XM® Radio Contact Information for XM® Radio: 1. You need your radio ID ready before registering for subscription. To see the ID in the display, press the n (TUNE) bar while in XM mode until “0” appears in the center display. Audio 2. Have your radio ID and credit card number ready, and either call XM or visit the XM website to subscribe.
Playing a Disc QRG 2014 RDX Selecting Disc Mode 1. Press the DISC button to play a CD or other disc. 2. Insert a disc into the disc slot. d “Display audio screen” You can control the disc using voice commands. 2 Disc Commands P. 248 The disc automatically begins playing. 3. Select a track using the bars (SKIP, TUNE, CATEGORY, SCAN/A.SEL). Audio The track number and elapsed time are displayed on the display.
Playing a DiscAudio Menu QRG 2014 RDX Audio Menu H AUDIO button (in DISC mode) AUDIO MENU Rotate i to select an item. Press u. Audio The following items are available, depending on the type of disc: • Record CD: Records a music CD onto the HDD for playback using HDD Audio. 2 Recording a Music CD to HDD P. 154 • Sound Setup: Displays the sound preferences screen. 2 Adjusting the Sound P.
Playing a DiscPlaying MP3/WMA/AAC Discs QRG 2014 RDX • Scan: 1: Scans all tracks on the disc (or in the selected folder) in the order they were recorded (stored) and plays a 10-second sample. Select OFF to stop scanning and play the current selection. 2: Scans the first track in each folder on the disc and plays a 10-second sample. Select OFF to stop scanning and play the current selection.
Playing a DiscRecommended Discs QRG 2014 RDX Recommended Discs • Use only high-quality CD-R or CD-RW discs labeled for audio use. • Use only CD-R or CD-RW discs on which the recordings are closed. • Play only standard round-shaped discs. • Use DVD-R/RW discs that meet DVD verification standards. The disc packages or jackets should have one of these symbols. Audio Also includes: ■ Recording to HDD • Only standard CD-DA (44.1 kHz, 16 bit stereo PCM digital sound data) discs can be recorded to HDD.
Playing Hard Disc Drive (HDD) Audio QRG 2014 RDX The Hard Disc Drive (HDD) Audio function plays tracks from music CDs that have been recorded onto the built-in HDD. You can arrange the tracks in playlists or play the tracks using various search methods. Selecting HDD Mode Audio 1. Press the HDD/AUX button to play tracks stored on the HDD. 2. Select a track by genre, artist, album, recording date, playlist, or track list. The track number and elapsed time are displayed on the display.
Playing Hard Disc Drive (HDD) AudioAudio Screen Control QRG 2014 RDX Audio Screen Control H AUDIO button (in HDD mode) 1 Audio Screen Control Control the audio screen through the navigation system. HDD mode Rotate i to select a track. Press u. Move w or y to select ALBUMor ALBUM+ to change albums. Audio Move e to select MUSIC SEARCH to display the Music Search Menu. 2 Searching for Music P. 156 . Move r to select AUDIO MENU 2 Audio Menu P.
Playing Hard Disc Drive (HDD) AudioAudio Menu QRG 2014 RDX The following items are available, depending on the type of playlist: • Sound Setup: Displays the sound preferences screen. 2 Adjusting the Sound P. 176 • Repeat 6: Repeats the current track. Audio • Random F: Plays all tracks on the HDD in random order. • Scan 1: Scans all tracks on the HDD in the order they were recorded and plays a 10second sample. Select OFF to stop scanning and play the current selection.
Playing Hard Disc Drive (HDD) AudioRecording a Music CD to HDD QRG 2014 RDX Recording a Music CD to HDD The songs on music CDs are automatically recorded by factory default to the HDD the first time you play each disc. You can then play the songs directly from the HDD. Recording indicator Recorded Audio Recording Ready to record ■ Stopping Recording 1. Move r to select AUDIO MENU. 2. Rotate i to select Cancel CD Recording. Press u.
Playing Hard Disc Drive (HDD) AudioRecording a Music CD to HDD QRG 2014 RDX ■ Recording a CD Manually 1 Recording a CD Manually H AUDIO button (in DISC or HDD mode) AUDIO MENU HDD Setup 1. Rotate i to select CD Recording. Press u. 2. Rotate i to select MANUAL. Press u. Music Search Setup Use this feature to set up the music search abilities when using Song By Voice™ (SBV) commands. 2 Music Search Setup P. 44 Audio 3. Move r to select RETURN. 4. Move r to select AUDIO MENU. 5.
Playing Hard Disc Drive (HDD) AudioSearching for Music QRG 2014 RDX Searching for Music H AUDIO button (in HDD mode) MUSIC SEARCH Search for music recorded to HDD using six different methods. 1. Rotate i to select a search category. Press u. Albums, Artists, and Tracks display lists in alphabetical order. Record Date displays albums in chronological order. Audio You can also search for music on the HDD through voice commands using SBV. 2 Searching for Music Using Song By Voice™ (SBV) P.
Playing Hard Disc Drive (HDD) AudioEditing a Playlist or Album QRG 2014 RDX Editing a Playlist or Album H AUDIO button (in HDD mode) AUDIO MENU Edit Album or Edit Playlist Change the playlist name, album name, genre, and track order of the current playlist. You can also delete tracks, playlists, and albums. Rotate i to select an item. Press u. 1 Editing a Playlist or Album The maximum number of songs in each of the six user playlists is 999. Adding new songs overwrites the oldest songs.
Playing Hard Disc Drive (HDD) AudioEditing Track Information QRG 2014 RDX Editing Track Information H AUDIO button (in HDD mode) AUDIO MENU Edit Track Change the album name, track title, artist name, and genre. You can also delete tracks. Rotate i to select an item. Press u. Audio The following items are available: • Edit Track Name: Edits track name and artist name. Rotate i to select an option. Press u. • Delete Track: Deletes the current track.
Playing Hard Disc Drive (HDD) AudioDisplaying Music Information QRG Displaying Music Information 2014 RDX H AUDIO button (in HDD mode) AUDIO MENU Get Album Info Display the music information (album name, artist name, genre) for an album (original playlist). Gracenote® searches for the information of the currently selected album (original playlist). Audio Rotate i to select an album. Press u. The information is displayed.
Playing Hard Disc Drive (HDD) AudioUpdating Gracenote® Album Info QRG 2014 RDX Updating Gracenote® Album Info H AUDIO button (in HDD or DISC mode) AUDIO MENU HDD Setup Update the Gracenote® Album Info (Gracenote® Media Database) that is included with the navigation system. Remaining capacity Maximum capacity 1. Insert the update disc into the disc slot or connect the USB flash drive that includes the update. Audio 2. Rotate i to select Update Gracenote Info. Press u. 3.
Playing an iPod® QRG 2014 RDX ■ Connecting an iPod® 1 Connecting an iPod® • Do not use an extension cable with the USB adapter cable. • Do not connect your iPod® using a hub. • Do not use a device such as a card reader or hard disk drive, as the device or your tracks may be damaged. Audio • We recommend backing up your data before using the device in your vehicle. • Displayed messages may vary depending on the device model and software version. 1.
Playing an iPod®Selecting iPod® Mode QRG 2014 RDX Selecting iPod® Mode 1. Connect the iPod® to the USB adapter cable in the console compartment. 2. Press the HDD/AUX button until you get to iPod® mode. 3. Select a track using the iPod® menu on the screen. The current track number and total number of tracks are displayed. Audio Audio Screen Control H AUDIO button (in iPod® mode) Control the audio screen through the navigation system. iPod® mode Track list 162 . Rotate i to select a track.
Playing an iPod®Audio Menu QRG 2014 RDX Audio Menu H AUDIO button (in iPod® mode) AUDIO MENU Rotate i to select an item. Press u. Audio The following items are available: • Sound Setup: Displays the sound preferences screen. 2 Adjusting the Sound P. 176 • Music Search Setup: Use this feature to set up the music search abilities when using Song By Voice™ (SBV) commands. 2 Music Search Setup P. 44 • Repeat 6: Repeats the current track. • Shuffle: F: Plays all tracks in the track list in random order.
Playing an iPod®Searching for Music QRG 2014 RDX Searching for Music H AUDIO button (in iPod® mode) MUSIC SEARCH Search for music using the iPod® menu. 1. Rotate i to select a search category. Press u. The order of the track list displayed if you select “All” on the iPod® menu varies depending on the iPod® model and software. Audio You can also search for music on the iPod® through voice commands using SBV. 2 Searching for Music Using Song By Voice™ (SBV) P.
Searching for Music Using Song By Voice™ (SBV) QRG 2014 RDX Use Song By Voice™ (SBV) to search for and play music from your HDD or iPod® device using voice commands. 1. Set Song By Voice to ON in the system setup. 2 Song By Voice™ (SBV) P. 45 Audio 2. Say d “Hard Disc Drive Search” or d “iPod Search” to activate the SBV feature for the HDD or iPod®. The SBV commands that you can use are displayed on the screen. 3. Say a command.
Playing Pandora® QRG 2014 RDX Pandora® is a personalized Internet radio service that selects music based on an artist, song, or genre a user enters, and streams what is likely to be of interest. Selecting Pandora® Mode 1. Activate Pandora® on your iPhone®. Audio 2. Connect the iPhone® to the USB adapter cable in the console compartment. 2 Connecting an iPod® P. 161 3. Press the HDD/AUX button until you get to Pandora® mode. 4. Select a station using the CATEGORY bar.
Playing Pandora®Audio Screen Control QRG 2014 RDX Audio Screen Control H AUDIO button (in Pandora® mode) 1 Audio Screen Control Control the audio screen through the navigation system. Pandora® mode Rotate i to select an item. Press u. The following functions are not available on this navigation system: Audio • Buy from iTunes • Email the Current Station • Check Song Detail • Create Station You can skip the song only a predetermined number of times in an hour.
Playing Pandora®Audio Menu QRG 2014 RDX Audio Menu H AUDIO button (in Pandora® mode) AUDIO MENU Rotate i to select an item. Press u. Audio The following items are available: • Sound Setup: Displays the sound preferences screen. 2 Adjusting the Sound P. 176 • Album Art: Sets whether to display the album artwork on the screen. ON (factory default): Displays the album artwork. OFF: Disable the feature. • BOOKMARK This Song: Bookmarks the current song.
Playing Pandora®QuickMix QRG 2014 RDX QuickMix H AUDIO button (in Pandora® mode) Station List Rotate i to select QuickMix. Press u. Starts to randomly play tracks from all your stored stations in the list. To cancel the QuickMix mode, select another station.
Playing a USB Flash Drive QRG 2014 RDX ■ Connecting a USB Flash Drive 1 Connecting a USB Flash Drive • Do not use an extension cable with the USB adapter cable. • Do not connect your USB flash drive using a hub. • Do not use a device such as a card reader or Audio hard disk drive, as the device or your tracks may be damaged. • We recommend backing up your data before using the device in your vehicle. 1. Unclip the USB connector in the front console and loosen the adapter cable. 2.
Playing a USB Flash DriveSelecting USB Mode QRG 2014 RDX Selecting USB Mode 1 Playing a USB Flash Drive 1. Connect the USB flash drive to the USB adapter cable in the console compartment. d “Display audio screen” You can control the USB flash drive using voice commands. 2 USB Commands P. 248 2. Press the HDD/AUX button until you get to USB mode. 3. Select a track using skip, scan, folder list, or track list. A visual guide helps you operate the audio system. 2 System Controls P.
Playing a USB Flash DriveAudio Menu QRG 2014 RDX Audio Menu H AUDIO button (in USB mode) AUDIO MENU Rotate i to select an item. Press u. Audio The following items are available: • Sound Setup: Displays the sound preferences screen. 2 Adjusting the Sound P. 176 • Repeat: 6: Repeats the current track. 7: Repeats all tracks in the current folder. • Random: F: Plays all tracks on the USB flash drive in random order. I: Plays all tracks in the current folder in random order.
Playing a USB Flash DrivePlaying Tracks in Folders QRG 2014 RDX Playing Tracks in Folders H AUDIO button (in USB mode) FOLDERS 1 Playing Tracks in Folders Change the folder if the tracks are stored in a folder structure. 1. Rotate i to select a folder. Press u. The system displays the track list. Folder List • Any music tracks not in a folder are automatically added to a “ROOT” folder, which is displayed at the top of the Folder List.
Playing Bluetooth® Audio QRG 2014 RDX Your audio system allows you to listen to music tracks stored on your Bluetoothcompatible phone. This function is available when the phone is linked to the vehicle’s Bluetooth® HandsFreeLink® (HFL) system. 2 Bluetooth® HandsFreeLink® P. 179 Audio Selecting Bluetooth® Audio Mode 1. Make sure that your phone is on, paired, and linked to HFL. 2 Pairing a Phone P.
Playing Bluetooth® AudioSwitching to HFL Mode QRG 2014 RDX Switching to HFL Mode h (Pick-Up) button 1. If you receive a call when Bluetooth® Audio is playing, press the h (Pick-Up) button on the steering wheel to answer the call. 2 Bluetooth® HandsFreeLink® P. 180 Audio j (Hang-Up) button 2. Press the j (Hang-Up) button to end the call, and Bluetooth® Audio is resumed. Audio Screen Control If more than one phone is paired to the HFL system, there may be a delay before the system begins to play.
Adjusting the Sound QRG 2014 RDX H AUDIO button AUDIO MENU Sound Setup Adjust the sound bass, treble, fader, and balance. You can also adjust the strength of the sound coming from the center and subwoofer speakers. In addition, you can set Dolby PL (ProLogic) II and Speed-sensitive Volume Compensation (SVC). 1. Rotate i to select the sound mode to adjust. Press u. Audio 2. Rotate i to adjust the desired level. Press u. The display returns to the audio screen after a few seconds.
Audio Remote Controls QRG 2014 RDX Steering Wheel Controls 1 MODE Button Control basic audio system functions using the controls mounted on the steering wheel.
Audio Remote ControlsSteering Wheel Controls QRG 2014 RDX ■ CH (Channel) Button FM/AM, XM • Press the N (Channel) button to select the next preset station (channel). • Press the B (Channel) button to select the previous preset station (channel). • FM/AM: Press and hold for one second to scan for a station with a strong signal. Audio • XM: Press and hold for one second to skip to the next or previous station (channel) in the current category.
QRG 2014 RDX Bluetooth® HandsFreeLink® This section describes how to operate Bluetooth® HandsFreeLink®. You can place and receive phone calls using your vehicle’s audio system without handling your cell phone. Bluetooth® HandsFreeLink® ............... 180 Pairing a Phone .................................... 182 Setting Up Speed Dialing...................... 187 Editing User Name and PIN................... 189 Phone Setup ........................................ 190 Making a Call..........................
Bluetooth® HandsFreeLink® QRG 2014 RDX H PHONE button 1 Bluetooth® HandsFreeLink® Rotate i to select an item. Press u. You can control the HFL system using voice commands. 2 HFL Menus P. 196 To use HFL, you need a Bluetooth-compatible cell phone. For a list of compatible phones, pairing procedures, and special feature capabilities: Bluetooth® HandsFreeLink® • U.S.: Visit www.acura.com/handsfreelink. • Canada: Visit www.handsfreelink.ca.
Bluetooth® HandsFreeLink® QRG 2014 RDX ■ Help Features Say d “Help” any time to get help or hear a list of commands. 2 Voice Help P. 5 1 Bluetooth® HandsFreeLink® Bluetooth® Wireless Technology Bluetooth® name and logos are registered trademarks owned by Bluetooth SIG, Inc., and any use of such marks by Honda Motors Co., Ltd., is under license. Other trademarks and trade names are those of their respective owners.
Bluetooth® HandsFreeLink®Pairing a Phone QRG 2014 RDX Pairing a Phone H PHONE button 1 Pairing a Phone When no Bluetooth-compatible phone has ever been paired to the system, the following screen appears: 1. Rotate i to select Yes. Press u . 2. Put your cell phone in “Discovery” or “Search” mode. 3. Press u to select OK. Bluetooth® HandsFreeLink® The system begins to search for your phone. Your Bluetooth-compatible phone must be paired to HFL before you can make and receive hands-free calls.
Bluetooth® HandsFreeLink®Pairing a Phone QRG 2014 RDX ■ Pairing from Phone Setup 1 Pairing from Phone Setup H PHONE button PHONE SETUP Connection If a prompt appears asking to connect to a phone, select No and proceed with step 1. Use the Phone Setup screen to pair an additional Bluetooth-compatible phone if a phone has been previously paired to the system. Delete a Phone You can delete the paired phone. 2 Deleting a Paired Phone P. 185 1. Rotate i to select Add New Phone. Press u. 2.
Bluetooth® HandsFreeLink®Pairing a Phone QRG 2014 RDX ■ Changing the Pass-key H PHONE button PHONE SETUP Connection 1. Rotate i to select Pass-key. Press u. Bluetooth® HandsFreeLink® 2. Rotate i to select an item. Press u. The following items are available: • Random: Uses a randomly generated pass-key. • Fixed: Create your own pass-key (factory default is 0000).
Bluetooth® HandsFreeLink®Pairing a Phone QRG 2014 RDX 3. If you select Fixed, move w to select DELETE to remove the current pass-key. 4. Enter a new pass-key. Move r to select OK. Bluetooth® HandsFreeLink® ■ Deleting a Paired Phone 1 Deleting a Paired Phone H PHONE button PHONE SETUP Connection 1. Rotate i to select Delete. Press u. Continued When you transfer the vehicle to a third party, delete all paired phones.
Bluetooth® HandsFreeLink®Pairing a Phone QRG 2014 RDX Trash icon 2. Rotate i to select a phone to delete. Press u. The Bluetooth® icon indicates the currently linked phone. Items to be deleted are indicated with a trash icon. 3. Move r to select OK. Bluetooth® HandsFreeLink® Bluetooth® icon 4. Rotate i to select Yes. Press u to delete the device(s). ■ Changing the Currently Paired Phone H PHONE button PHONE SETUP Connection 1. Rotate i to select Connect. Press u. 2.
Bluetooth® HandsFreeLink®Setting Up Speed Dialing QRG 2014 RDX Setting Up Speed Dialing H PHONE button PHONE SETUP Edit Speed Dial Store Speed Dial Create speed dial entries with voice tags for easy calling. 1. Rotate i to select a location in the speed dial list. Press u. 1 Setting Up Speed Dialing You can control the HFL system using voice commands. 2 HFL Menus P. 196 Up to 20 speed dial entries can be stored per user. The first three entries are displayed on the Cellular Phone screen.
Bluetooth® HandsFreeLink®Setting Up Speed Dialing QRG 2014 RDX ■ Registering a Voice Tag to a Speed Dial Entry H PHONE button PHONE SETUP Edit Speed Dial 1. Rotate i to select Store Voice Tag. Press u. 2. Rotate i to select a speed dial entry. Press u. 1 Registering a Voice Tag to a Speed Dial Entry Voice tags allow you to call speed dial entries from any screen by saying d “Dial by voice tag” and the voice tag, followed by d “Dial.” • Avoid using duplicate voice tags.
Bluetooth® HandsFreeLink®Editing User Name and PIN QRG 2014 RDX Editing User Name and PIN H PHONE button PHONE SETUP Edit Phone Name/PIN Edit the user name of a paired phone, and protect the phonebook and speed dial entries with a PIN. Rotate i to select an item. Press u. 1 Editing User Name and PIN You can control the HFL system using voice commands. 2 HFL Menus P. 196 You can name up to six HFL users. Each can be PIN protected, and have their own phonebook, speed dial entries, and call history.
Bluetooth® HandsFreeLink®Phone Setup QRG 2014 RDX Phone Setup H PHONE button PHONE SETUP 1 Phone Setup Set HFL options and features. 1. Rotate i to select an item. Press u. 2. Rotate i to select an option. Press u. Bluetooth® HandsFreeLink® The following items are available: • Connection: Pairs your phone to the system, connect/disconnect your phone, or changes the pass-key. 2 Pairing a Phone P. 182 • Edit Speed Dial: Stores/deletes the speed dials or edits the voice tag.
Bluetooth® HandsFreeLink®Phone Setup QRG 2014 RDX • Clear Cellular Phone Information: Clear all paired phones, phonebook entries, speed dials, and pass-keys. • Text Message Notice: Sets whether to give an incoming message notification. 1 Phone Setup Text Message Notice can be set separately for each paired phone. ON (factory default): Gives an incoming message notification. OFF: Messages are still received, but without notification.
Bluetooth® HandsFreeLink®Making a Call QRG 2014 RDX Making a Call Make calls by entering a number or using the imported phonebook, call history, or speed dial entries. 2 Using the Phonebook P. 193 2 Entering a Phone Number P. 193 2 Using Call History P. 194 2 Using Speed Dial P. 194 1 Making a Call You can control the HFL system using voice commands. 2 HFL Menus P.
Bluetooth® HandsFreeLink®Making a Call QRG 2014 RDX ■ Using the Phonebook 1 Using the Phonebook H PHONE button Phone Book 1. Rotate i to select a name. Press u. Move w or y to select alphabetical tabs to display the entries in the group. Bluetooth® HandsFreeLink® 2. Rotate i to select a number. Press u to begin dialing. ■ Entering a Phone Number H PHONE button Dial 1. Enter a phone number. Your phonebook is automatically imported when the phone is paired.
Bluetooth® HandsFreeLink®Making a Call QRG 2014 RDX ■ Using Call History 1 Using Call History H PHONE button Call History Rotate i to select a call. Press u to begin dialing. The call history only shows the last 20 calls from your phone. Move w or y to select All, Dial, Receive, Missed to view the call history by category. Bluetooth® HandsFreeLink® 194 ■ Using Speed Dial 1 Using Speed Dial From the Cellular Phone screen: Rotate i to select one of the three speed dial numbers.
Bluetooth® HandsFreeLink®Receiving a Call QRG 2014 RDX Receiving a Call 1. Press the h (Pick-Up) button to answer a call and display the Calling screen. “HANDSFREELINK” is also displayed on the display. Call ID Bluetooth indicator Roaming status Bluetooth® HandsFreeLink® 2. Press the j (Hang-Up) button to terminate the call. 1 Receiving a Call An incoming call notification appears on the screen, and you hear an audible ring tone.
Bluetooth® HandsFreeLink®HFL Menus QRG 2014 RDX HFL Menus 1 HFL Menus The power mode must be in ACCESSORY or ON to use HFL. You can operate HFL by voice when on the Cellular Phone screen. Below is the flow chart showing available voice commands. To use HFL, you must first pair your Bluetoothcompatible cell phone to the system while the vehicle is parked. Press the h (Pick-Up) button to display the Cellular Phone screen. Press the d (Talk) button each time you give a voice command.
Bluetooth® HandsFreeLink®HFL Menus QRG 2014 RDX “Name” Create a user name for a paired phone. “Edit Phone Name/PIN” 2 Editing User Name and PIN P. 189 “PIN” Create a PIN for a paired phone. Turn the auto transfer on or off. “Auto Transfer On/Off” 2 Phone Setup P. 190 Bluetooth® HandsFreeLink® “Auto Answer On/Off” Turn the auto answer on or off. 2 Phone Setup P. 190 “Clear Cellular Phone Delete all paired phones, phonebook entries, speed dials, and pass-keys. 2 Phone Setup P.
Bluetooth® HandsFreeLink®HFL Menus QRG 2014 RDX “Dial” Say a phone number to dial. 2 Entering a Phone Number P. 193 “Dial Tones” “Mute” Bluetooth® HandsFreeLink® “Transfer” “Text Message” “More Speed Dial” “Dial” Send numbers or names during a call. Mute your voice during a call. Transfer a call from HFL to your phone, or from your phone to HFL. Display received text messages list. 2 Text Messages P. 184 Display a list of all 20 speed dial entries. 2 Using Speed Dial P.
Text Messages QRG 2014 RDX If your paired phone is compatible, you can receive and hear text messages and reply to them using fixed reply messages. 2 Pairing a Phone P. 182 If a text message is received, the following screen is displayed. 1. Rotate i to select Read. Press u. The text message is read aloud. Select Cancel to check the text message later. Bluetooth® HandsFreeLink® If the phone number of the sender is stored to the Phonebook, the name is displayed. 2. Rotate i to select an item.
Text MessagesHFL Menus QRG 2014 RDX • Reply: Replies to the message using a fixed reply message. You cannot create your own messages. 2 Replying to the Message P. 200 • Call: Calls the sender. • Full Message: Displays the entire message body. You can set up text message notification when the first message for the paired phone is received. You can change the setting from the Phone Setup screen. 2 Phone Setup P. 190 If you delete a message on the phone, the message is also deleted in the system.
QRG 2014 RDX AcuraLink® Messages This section describes how Acura directly communicates important information to you regarding your vehicle. AcuraLink® Messages .......................... 202 Reading Messages................................ 202 Message Categories ............................. 203 Message Options ................................. 204 Dealer Appointments ...........................
AcuraLink® Messages QRG 2014 RDX AcuraLink® provides a direct communication link between your vehicle and Acura. Working through XM® Radio, AcuraLink works in conjunction with your vehicle’s navigation system, Bluetooth® HandsFreeLink® (HFL), and audio system to send and receive messages. Reading Messages An envelope icon appears at the bottom left of the navigation screen when there is a new message.
AcuraLink® MessagesMessage Categories QRG 2014 RDX ■ All Messages 1 All Messages H INFO button Messages 1. Rotate i to select a message category. Press u. An unread message has a closed envelope icon next to it. The icon disappears once you read the message. 2. Rotate i to select a message. Press u. AcuraLink® Messages Message Categories 1 Message Categories There are six message categories in AcuraLink.
AcuraLink® MessagesMessage Options QRG 2014 RDX • Diagnostic Info: Provides information about the cause for a warning indicator or multi-information display message. Rotate i to select Check Later or Check Now. If you choose to check the information now, AcuraLink lets you know whether you should see a dealer immediately or later in accordance with the level of severity. Call a dealer or find the nearest dealer.
AcuraLink® MessagesDealer Appointments QRG 2014 RDX • Find Acura Dlr: Searches for the nearest Acura dealer. • Call Your Dealer: Calls Acura dealer using HFL. • Diagnostic Info: Updates, if any, the current diagnostic message by connecting to the Acura server using HFL. • Schedule Dealer Appt.: Automatically sets an appointment date at a dealer. Dealer Appointments 1 Dealer Appointments Schedule a dealer appointment for Maintenance Minder and Recalls/Campaigns messages.
QRG 206 2014 RDX
QRG 2014 RDX Other Features This section describes the useful functions incorporated into the navigation system. Calendar ................................................ 208 Calculator .............................................. 210 Unit Conversion ................................... 210 Information Functions .......................... 212 Scenic Road Information ...................... 212 System/Device Information ................... 212 Map Update Status ..............................
Calendar QRG 2014 RDX H INFO button Other Calendar 1 Calendar Enter events and display reminders each time you start your vehicle. 1. Rotate i to select the day. Press u. You can select the day of the month on the calendar using voice commands (e.g., say d “Five” to select the 5th). Move w or y to scroll through the months of the year. Only one event entry can be stored for each date. Dates with an icon indicate there is a scheduled entry for that date.
Calendar QRG 2014 RDX • Message Icon: Select an icon from the list to help identify the type of message. The message icon you choose will be displayed alongside the specified date on the Calendar screen. • Reminder: Sets whether event reminders are displayed each time you start your vehicle. 2 Start-up P. 20 1 Calendar Message Icons The following icons can be selected: Schedule Time Restaurant Others Call • Delete: Deletes the event.
Calculator QRG 2014 RDX H INFO button Other Calculator Use the calculator to make basic calculations and to convert measurement units. Unit Conversion Other Features 210 1 Unit Conversion 1. Enter a numeric value to convert (e.g., 1000). 2. Move r to select UNIT CONVERSION. 3. Rotate i to select the type of unit to convert (e.g., Length). Press u. If you do not enter a value to convert, only “Temperature” units are selectable.
CalculatorUnit Conversion QRG 2014 RDX 4. Rotate i to select the base unit to convert from (e.g., mm). The conversion into other units is displayed on the right (e.g., 1000 mm is 39.37 inches). 5. Move y to select CALC. to return to the Calculator screen.
Information Functions QRG 2014 RDX Scenic Road Information H INFO button Other Scenic Road Information View a list of scenic roads for each state (U.S. only). 1. Rotate i to select a state. Press u. 1 Scenic Road Information If you select a scenic road that runs through multiple states, only the portion of the road in the selected state is displayed. You can also set the scenic road as a destination or waypoint. 2. Rotate i to select a scenic road. Press u. 3.
Information FunctionsMap Update Status QRG 2014 RDX Map Update Status H INFO button Other Map Update Status 1 Map Update Status This operation is only available during a database update. 2 Obtaining a Navigation Update Data P. 235 Check the map data update status when updating the map database. Roadside Assistance 1 Roadside Assistance H INFO button Other Roadside Assistance Other Features Acura Roadside Assistance is provided as a service to Acura clients.
Information FunctionsKey to ZAGAT Ratings QRG 2014 RDX 2. Rotate i to select Call. Press u to begin dialing. Key to ZAGAT Ratings 1 Key to ZAGAT Ratings H INFO button Other Key to ZAGAT Rating Food, Decor, and Service categories are rated using numbered values (e.g., 0-9, 10-15). The ZAGAT® survey for some restaurants is included in the database and displayed when entering a restaurant as a destination. You can view an explanation of the data displayed for the surveyed restaurants.
Information FunctionsShow Wallpaper QRG 2014 RDX Show Wallpaper H INFO button Other Show Wallpaper View the picture currently set as the wallpaper. Press the CANCEL button to return to the previous screen. 1 Show Wallpaper You can change the wallpaper picture. 2 Wallpapers Setting P.
Multi-View Rear Camera QRG 2014 RDX Your vehicle is equipped with a multi-view rear camera. When you shift into Reverse, the rear view is displayed on the navigation system screen. The edge of the bumper and parking guide lines are also displayed. To turn the guide lines on or off, press and hold the CANCEL button for about three seconds. Rotate i to adjust the screen brightness.
QRG 2014 RDX Troubleshooting Troubleshooting ................................... 218 Map, Voice, Entering Destinations ........ 218 Traffic .................................................. 220 Guidance, Routing ............................... 221 Update, Coverage, Map Errors ............. 223 Display, Accessories.............................. 223 Multi-View Rear Camera ...................... 223 Miscellaneous Questions ...................... 224 Error Messages......................................
Troubleshooting QRG 2014 RDX Map, Voice, Entering Destinations Problem Solution The Startup Confirmation screen is displayed every time I start the car. This is normal. The Startup Confirmation screen reminds you and your guest drivers to always operate the navigation system in a safe manner. If you do not select OK at startup, voice commands will not work. The navigation system reboots by itself (returns to the opening screen).
TroubleshootingMap, Voice, Entering Destinations QRG 2014 RDX Problem Solution Troubleshooting I cannot select an option using the Interface Dial. To prevent driver distraction, certain onscreen functions and features are limited or inoperable while the vehicle is moving. Use voice commands or pull over to proceed. The navigation system pronunciation of street names in the guidance command or destination address sounds strange.
TroubleshootingTraffic QRG 2014 RDX Traffic Problem Troubleshooting 220 Solution AcuraLink Real-Time Traffic™ information could not be received or is not displayed properly. • Check the traffic icon is displayed and enabled on the icon bar. • Your XM traffic subscription may have expired. Check your subscription. Call XM at (800) 852-9696 and verify your account status. If your subscription has lapsed, you may need to request a “rapid refresh.
TroubleshootingGuidance, Routing QRG 2014 RDX Guidance, Routing Problem The navigation system does not route me the same way I would go or the same way as other mapping systems. Solution The navigation system attempts to generate the optimal route. You can change the route preferences used when calculating a route. 2 Changing the Route Preference P. 92 The navigation system wants to route me around Press the INFO button.
TroubleshootingGuidance, Routing QRG 2014 RDX Problem Troubleshooting 222 Solution The vehicle position icon on the map “lags” a short distance behind, especially when I arrive at an intersection. This is normal. The navigation system is unaware of the width of intersections. Large differences in vehicle position can indicate a temporary loss of the GPS signal. 2 GPS System P. 232 The screen is showing white dots as I drive along. These dots are called “breadcrumbs.
TroubleshootingUpdate, Coverage, Map Errors QRG 2014 RDX Update, Coverage, Map Errors Problem Solution My city is not part of a fully verified detailed coverage area. The mapping database is constantly undergoing revision. You can access the most recent information on the internet. 2 Map Coverage P. 235 Does the navigation system work outside North America? The navigation system contains maps for the 50 U.S. states, Canada, Puerto Rico, and Mexico.
TroubleshootingMiscellaneous Questions QRG 2014 RDX Miscellaneous Questions Problem Solution My clock frequently changes forward and backward by The clock setting is automatically updated based on your GPS location. If you live and one hour. work on the boundary between two time zones, you can turn off this feature. 2 Clock Adjustment P. 57 Troubleshooting 224 The clock changes even when I am not driving near a time zone boundary.
Error Messages QRG 2014 RDX Navigation System Error Message The display temperature is too high! For protection, the display will shut down. Solution This message appears briefly when the display temperature is too high. The navigation system turns off until the display cools down. The system turns back on automatically when the display cools down. Cannot write to the HDD due to the low temperature.
Error MessagesDisc Player QRG 2014 RDX Disc Player Error Message Troubleshooting 226 Cause Solution • Press the E (Eject) button and remove the disc, and check that the error message is cleared. • Check that the disc is not damaged or deformed, and insert the disc again. 2 Recommended Discs P. 150 • If the error message reappears, press the E button, and pull out the disc. • Insert a different disc. If the new disc plays, there is a problem with the first disc.
Error MessagesiPod®/Pandora® QRG 2014 RDX iPod®/Pandora® Error Message Cause Solution Troubleshooting UNSUPPORTED Ver. Appears when an unsupported iPod® is connected. Update the iPod® software to the latest version. CONNECT RETRY Appears when the iPod® cannot be authenticated. Reconnect the iPod®. No Song Appears when there are no tracks Store tracks in the iPod®. in the iPod®. No station list on device. Use device to create station. Appears when there are no stations in Pandora®.
Error MessagesUSB Flash Drive QRG 2014 RDX USB Flash Drive Error Message Troubleshooting 228 Cause Solution File Error The system cannot read the track(s). Check the tracks in the USB flash drive. There is a possibility that the tracks have been damaged. Unsupported Appears when an unsupported device is connected. If it appears when a supported device is connected, reconnect the device. Unplayable File Appears when the tracks in the USB flash drive are DRM or an unsupported format.
QRG 2014 RDX Reference Information System Initialization ..............................230 Entering the Security Code....................230 Acquiring GPS Information....................230 Startup Confirmation Screen .................231 Map Matching ......................................231 System Limitations ................................232 GPS System...........................................232 Address Calculation ..............................232 Database ........................................
System Initialization QRG 2014 RDX The navigation system must be initialized if power to the navigation system is interrupted for any reason (e.g., the battery was disconnected). Entering the Security Code Reference Information Find the navigation system’s security code and serial number label in your Owner’s Manual kit. Do not store the label in your vehicle. If you lose the label, you must first retrieve the serial number, and then obtain the code.
System InitializationStartup Confirmation Screen QRG 2014 RDX Startup Confirmation Screen The Startup Confirmation screen is displayed when initialization has successfully completed. It is displayed every time you start your vehicle. Press u to select OK to continue. If you are experiencing GPS reception problems: 2 GPS System P. 232 Map Matching Map matching is the process of using the acquired GPS information to locate your position on the map screen.
System Limitations QRG 2014 RDX GPS System The signals received from the GPS satellites are extremely weak (less than a millionth of the strength of a local FM station) and require an unobstructed view of the sky. The GPS antenna is located in the dashboard.
System LimitationsDatabase QRG 2014 RDX In addition, the map database contains verified and unverified areas. Unverified streets may be missing from the map, in the wrong location, or have an incorrect name or address range. A message will warn you if your route includes unverified streets. Exercise additional caution when driving in unverified areas.
Client Assistance QRG 2014 RDX Resolving Problems Reporting Errors If you run into a specific issue that you cannot resolve, consult the following help resources: You can help to improve database accuracy by reporting any errors you encounter. • For navigation system issues: 2 Troubleshooting P. 218 There are also FAQs available online at www.acuranavi.com. • Report errors in freeways and main “verified” roads shown in black on the map at http://mapreporter.navteq.com/ dur-web-external/.
Client AssistanceMap Coverage QRG 2014 RDX Map Coverage The navigation system provides map coverage for the United States, Canada, Puerto Rico, and Mexico. The map coverage consists of accurately mapped (verified) metropolitan areas and a less accurate (unverified) rural database. Note that unverified areas are constantly being reviewed and converted to verified areas each year. Map coverage update information is available from Acura Client Relations or online at www.acuranavi.com.
Client AssistanceTraffic Information QRG 2014 RDX Traffic Information Continuously updated traffic information is available in major metropolitan areas across the 48 contiguous states and some cities in Canada. A list of coverage areas is available online. To find traffic information: 1. Visit www.acura.com/realtimetraffic. 2. Select Real-Time Traffic on the RDX. 3. Click AcuraLink Real-Time Traffic.
Legal Information QRG 2014 RDX Copyrights User Agreements • Infogroup-Data: Certain business data provided by Infogroup © 2011, All RIghts Reserved. ■ Navigation System User Agreement • EXIT-Data: © ZENRIN CO., LTD. 2011. All rights reserved. • Building foot print: © ZENRIN CO., LTD. 2011. All rights reserved. • Junction View Data: © ZENRIN USA, INC. 2011. All rights reserved. Reference Information • ZAGAT SURVEY: © 2012 Zagat Survey, LLC.
Legal InformationUser Agreements QRG 2014 RDX • The right to use the HDD shall expire either when the user destroys the HDD or software, or when any of the terms of this Agreement are violated and the Licensors exercise the option to revoke the license to use the HDD or software. • The terms and conditions hereof apply to all subsequent users and owners as well as to the original purchaser.
Legal InformationUser Agreements QRG 2014 RDX Reference Information CD and music-related data from Gracenote, Inc., copyright © 2000 to present Gracenote. Gracenote Software, copyright © 2000 to present Gracenote. One or more patents owned by Gracenote apply to this product and service. See the Gracenote website for a non-exhaustive list of applicable Gracenote patents.
Legal InformationUser Agreements QRG 2014 RDX deems sufficient. No warranty is made that the Gracenote Software or Gracenote Servers are error-free or that functioning of Gracenote Software or Gracenote Servers will be uninterrupted. Gracenote is not obligated to provide you with new enhanced or additional data types or categories that Gracenote may provide in the future and is free to discontinue its services at any time.
Legal InformationAs required by the FCC QRG 2014 RDX Pandora® internet radio is a internet radio service not affiliated with HONDA. More information is available at http:// www.pandora.com. Pandora, the Pandora logo, and the Pandora trade dress are trademarks or registered trademarks of Pandora Media, Inc., used with permission. As required by the FCC This device complies with Part 15 of FCC Rules and Industry Canada licence-exempt RSS standard(s).
QRG 242 2014 RDX
QRG 2014 RDX Voice Commands Voice Commands .................................. 244 Global Commands ............................... 244 Navigation Commands......................... 244 Climate Control Commands................. 246 Audio Commands ................................ 247 Cellular Phone Commands ................... 250 Main Setup Screen Commands ............ 250 On-Screen Commands ......................... 251 Spelling Assistance ...............................
Voice Commands QRG 2014 RDX Global Commands Navigation Commands The system accepts these commands on any screen. The system accepts these commands on a map/guidance screen.
Voice CommandsNavigation Commands QRG 2014 RDX ■ Map Scale Commands Register the current location (stores current location in the Address Book) Display north up Display heading up Display zoom in Display zoom out Voice Commands Display (specify scale): 1/20 mile (80 m) scale 1/8 mile (200 m) scale 1/4 mile (400 m) scale 1/2 mile (800 m) scale 1 mile (1600 m) scale 2 mile (3 km) scale 5 mile (8 km) scale 15 mile (24 km) scale 50 mile (80 km) scale 150 mile (240 km) scale 350 mile (560 km) scale 1000 m
Voice CommandsClimate Control Commands QRG Voice Commands 246 2014 RDX Fast food restaurant French restaurant German restaurant Greek restaurant Indian restaurant Italian restaurant Japanese restaurant Korean restaurant Mexican restaurant Seafood restaurant Thai restaurant Vegetarian restaurant Vietnamese restaurant Other restaurant Pizza restaurant Ice cream shop Shopping area Accessory store Book store Clothing store Shoe store Furniture store Grocery store Home improvement store Mall Office supply
Voice CommandsAudio Commands QRG 2014 RDX Voice Commands Rear defrost off* Climate control fresh air Climate control recirculate Climate control sync on* Climate control sync off* Climate control vent Climate control bi-level (vent and floor) Climate control floor Climate control floor and defrost Fan speed up Fan speed down Fan speed # (#: 1 to 7) Driver temperature # degrees (#: 57 to 87 °F) Passenger temperature # degrees (#: 57 to 87 °F) Driver temperature up Driver temperature down Passenger temp
Voice CommandsAudio Commands QRG 2014 RDX ■ Disc Commands DISC play DISC play track # (#: 1 to 30) DISC skip forward DISC skip back DISC track random* DISC track repeat* DISC track scan* DISC folder up DISC folder down DISC folder random* DISC folder repeat* DISC folder scan* DISC normal play (cancels random, repeat, or scan play mode, resumes normal play mode) Voice Commands 248 * These commands toggle the function on and off, so the command may not match your intended action .
Voice CommandsAudio Commands QRG 2014 RDX ■ iPod® Commands iPod play iPod search (activates Song By Voice™) iPod play track # (#: 1-30) iPod skip forward iPod skip back iPod track shuffle* iPod album shuffle* iPod track repeat* iPod normal play (cancels repeat or shuffle play mode, resumes normal play mode) What/Who am I listening to? Who is this? What’s playing? Who’s playing? What album is this? Voice Commands * These commands toggle the function on and off, so the command may not match your intende
Voice CommandsCellular Phone Commands QRG 2014 RDX ■ Song By Voice™ Commands Voice Commands iPod search (activates Song By Voice™) HDD search (activates Song By Voice™) List album (specify album) List artist (specify artist) List composer (specify composer) List genre (specify genre) List playlist (specify playlist) Play album (specify album) Play artist (specify artist) Play composer (specify composer) Play genre (specify genre) Play playlist (specify playlist) Play song (specify song) What/Who am I
Voice CommandsOn-Screen Commands QRG 2014 RDX On-Screen Commands The system accepts these commands on any screen. There are over 100 on-screen commands. Say what is written on the screen to activate that selection. For lists, you can say the list item number to select that item.
Voice CommandsSpelling Assistance QRG 2014 RDX Say … Voice Commands 252 Or say… ■ Accented Letters Say … Say … or Symbol … N Nancy/November Û U circumflex O Oscar Ü U umlaut P Paul/Papa Q Queen/Quebec R Robert/Romeo S Sam/Sierra T Tom/Tango U Uncle/Uniform V Victor W William/Whiskey X X-ray Y Yellow/Yankee Z Zebra/Zulu Say … Say … or Symbol … À A grave  A circumflex Ä A umlaut Ç C cedilla È E grave É E acute Ê E circumflex Ë E umlaut Ì I grave Î
Voice CommandsSpelling Assistance QRG 2014 RDX ■ Punctuation Marks Say … ■ Symbols Say … or Symbol … Say … Say … Say … or Symbol … > Greater than { Open brace } Close brace k Enter Say … or Symbol … Voice Commands @ At sign - Hyphen ^ Caret ! Exclamation point * Asterisk “ Double quote _ Underscore # Pound ` Back quote $ Dollar , Comma % Percent .
List of Categories QRG 2014 RDX Auto Service All Types Acura Dealers* Acura Roadside Assistance Honda Dealers* Gas Station* Hydrogen Station Auto Parts & Electronics Auto Repair & Maintenance List of Categories 254 Car Wash & Detailing Motorcycle Dealers Other Car Dealers Parking Garage/House Parking Lot Rental Car Agency Roadside Assistance Lodging Hotel/Motel Shopping All Types Mall/Department Store Accessories/Jewelry Office Supplies/Electronics Auto Parts & Electronics Pharmacy/Drug Store Leisur
Index A B C D E F G H I J K L M N O P Q R S QRG T U V W X Y Z 2014 RDX Symbols K (Back) Button .................................. 5, 22 a (Display Mode) Button .................... 29 j (Hang-Up) Button .............................. 195 h (Pick-Up) Button ........................ 195, 196 8 (Sound) Button .......................... 6, 176 d (Talk) Button .................................... 5, 22 A A.SEL (Auto Select) ..................................
Index A B C D E F G H I J K L M N O P Q R S QRG U V W X Y Z 2014 RDX Clock Adjustment ......................................57 Adjust Time ..............................................58 Auto Daylight ...........................................57 Auto Time Zone .......................................57 Resetting ..................................................58 Color ...........................................................27 Map Color .......................................
Index A B C D E F G H I J K L M N O P Q QRG HDD/AUX Button ........ 6, 151, 162, 171, 174 Heading-up ............................................. 109 Home Address 1 .................................. 12, 41 Home Address 2 .................................. 12, 41 I J Icon Option ............................................. 108 Interface Dial ............................................... 8 Interface Dial Feedback ............................ 25 Intersection .........................
Index A B C D E F G H I J K L M N O P Q QRG Place Phone No. Editing Address Book ...............................39 Setting Destination ...................................84 Preset Buttons .............................................6 Previous Destinations Deleting ...................................................43 Editing Address Book ...............................39 Setting Destination ...................................76 Q Quick Tips ..............................................
Index A B C D E F G H I J K L M N O P Q QRG R S T U V W X Y Z 2014 RDX TUNE Bar ..................................................... 6 U Unit Conversion ....................................... 210 Units (mile or km) ..................................... 26 Unverified Area Routing .......................... 50 Update Gracenote Info ........................... 160 Update System Software Finding Update Information ................... 235 Obtaining Update Data .....................
