Bruksanvisning

ManualsBrandsAcuity Merker ManualsLight BarAcuity Brands LED Light Bar Kit

Page 1 of 7

912-00089-002

LED IM PORTANT SAFETY INSTRUCTIONS

 To reduce the risk of deat h, personal injury or property damage from fire, electric shock, falling parts, cuts/ abrasions, and

ot her hazards please read all w arnings and inst ruct ions included with and on the fixture box and all fixture labels.

 Before installing, servicing, or performing routine maint enance upon this equipm ent, follow t hese general precaut ions.

 Inst allation and service of luminaires should be performed by a qualified licensed electrician.

 M aint enance of the luminaires should be performed by person(s) familiar w ith the luminaires’ const ruction and operation

and any hazards involved. Regular fixt ure maintenance programs are recomm ended.

 It will occasionally be necessary to clean the outside of the refractor/ lens. Frequency of cleaning will depend on ambient

dirt level and minim um light output w hich is accept able to user. Refract or/ lens should be washed in a solut ion of w arm

water and any mild, non-abrasive household detergent , rinsed with clean w ater and wiped dry. Should optical assem bly

becom e dirty on t he inside, wipe refractor/ lens and clean in above manner, replacing dam aged gasket s as necessary.

 DO NOT INSTALL DAM AGED PRODUCT! This luminaire has been properly packed so that no parts should have been

damaged during transit. Inspect t o confirm. Any part damaged or broken during or after assembly should be replaced.

 Recycle: For informat ion on how to recycle LED electronic products, please visit

www.epa.gov.

 These inst ructions do not purport to cover all details or variat ions in equipment nor t o provide every possible cont ingency

to meet in connection with installat ion, operation, or m aintenance. Should further information be desired or should

particular problem s arise which are not covered sufficiently for the purchaser’s or owner’s purposes, t his matt er should be

referred t o Acuit y Brands Lighting, Inc.

READ AND FOLLOW ALL SAFETY INSTRUCTIONS!

SAVE THESE INSTRUCTIONS AND DELIVER TO OWNER AFTER INSTALLATION

 Disconnect or turn off power before

installation or servicing.

 Verify that supply voltage is correct by

comparing it wit h the luminaire label

inform ation.

 M ake all electrical and grounded

connections in accordance with the National

Electrical Code (NEC) and any applicable

local code requirements.

 All wiring connections should be capped

with UL approved recognized wire

connectors.

WARNING

RISK OF ELECTRIC SHOCK

 Allow lamp/ fixture to cool before handling.

Do not touch enclosure or light source.

 Do not exceed maximum wat tage marked on

luminaire label.

 Follow all manufacturer’s w arnings,

recommendations and restrictions for: driver

type, burning posit ion, mounting

locations/ methods, replacement and

recycling.

WARNING

RISK OF BURN

 Wear gloves and safet y glasses at all times

when removing luminaire from carton,

installing, servicing or performing

maintenance.

 Avoid direct eye exposure to the light source

while it is on.

CAUTION

RISK OF INJURY

 Keep combustible and other mat erials that

can burn, away from lamp/ lens.

 Do not operate in close proximity to persons,

combust ible materials or substances

affected by heat or drying.

CAUTION

RISK OF FIRE

Pre-Launch

Summary of content (7 pages)

PAGE 1
LED IM PORTANT SAFETY INSTRUCTIONS READ AND FOLLOW ALL SAFETY INSTRUCTIONS! SAVE THESE INSTRUCTIONS AND DELIVER TO OWNER AFTER INSTALLATION   au   h    To reduce t he risk of deat h, personal injury or propert y damage from fire, electric shock, falling part s, cut s/ abrasions, and ot her hazards please read all w arnings and inst ruct ions included wit h and on t he fixt ure box and all fixt ure labels.
PAGE 2
LED IM PORTANT SAFETY INSTRUCTIONS CAUTION: RISK OF PRODUCT DAM AGE  Never connect components under load.  Do not mount or support these fixtures in a manner t hat can cut the outer jacket or damage w ire insulation.  Controls for dimming, auto-sensing, or remote control of a luminaire that are not factory-w ired to the      h nc    au  -L  luminaire must be checked for com patibility w ith the luminaire prior to installation.
PAGE 3
LED IM PORTANT SAFETY INSTRUCTIONS INSTALLATION INSTRUCTIONS LBK TROFFER Inst allat ion inst ruct ions for Fixt ure Conversion Ret rofit Classified by Underw rit ers laborat ory Inc h The Ret rofit Kit cont ains LIGHT BAR #8-18 PAN HEAD TEK SCREWS nc #8-18 TEK SCREWS No. of Light bars No. of LED Drivers Hardw are 2 FT Qt y. (2) - 2FT BAR 1 (12) TEK SCREWS, (2) PAN HEAD TEK SCREWS, (1) 2FT RED JUM PER, (1) 2FT BLUE JUM PER 4 FT Qt y.
PAGE 4
LED IM PORTANT SAFETY INSTRUCTIONS INSTALLATION INSTRUCTIONS LBK TROFFER M inimum dimensions of t he host housing This Retrofit Kit is designed to fit housings w ith minimum dimensions: 4.9 inches nc h 2.3 inches Pr e -L au W ARNING – Risk of fire or electric shock. Lum inaires w iring, ballast s, or ot her elect rical part s m ay be dam aged w hen drilling for inst allation of reflect or kit hardw are. Check for enclosed wiring and com ponent s. W ARNING – Risk of fire or electric shock.
PAGE 5
LED IM PORTANT SAFETY INSTRUCTIONS INSTALLATION INSTRUCTIONS LBK TROFFER Inst allat ion Inst ruct ions: Step 1:  Verify fixt ure pow er is t urned off.  Rem ove lam ps and channel/ ballast cover from exist ing fixt ure.  Ident ify and disconnect pow er supply w ires. h  Rem ove ballast (s), invert inst all lam pholders, and au nc rem ove int ernal wiring t o provide adequate clearance for Retrofit Kit inst allat ion.
PAGE 6
LED IM PORTANT SAFETY INSTRUCTIONS INSTALLATION INSTRUCTIONS LBK TROFFER Step 3:  At t ach safety tet her t o host housing using exist ing nail h pierce/ extruded holes and provided self t apping screw s.  Cent er and inst all Light bar in host housing using self t apping screw s provided (m inim um 2 screw on eit her side).  Connect LED Harness (red and blue) t o t he LED Driver (red and blue).
PAGE 7
LED IM PORTANT SAFETY INSTRUCTIONS INSTALLATION INSTRUCTIONS LBK TROFFER nc h Wiring Diagrams 2 LightBar Solution -L au 1 LightBar Solution 3 Lightbar Solution Step 4: 4 LightBar Solution Pr e  Inst all original ballast cover over t he driver and t hen inst all t he diffuser fram e ont o host housing.  Turn on t he fixture.