CP9695 AutoScanner® Pro en User guide
en | 2 | User guide | CP9695 AutoScanner® Pro Serial No: ___________________________________ SW ID: ______________________________________ HW Ver: _____________________________________ Boot Ver: ____________________________________ Prod ID: _____________________________________ Board ID: ____________________________________ Burn Date: __________________________________ Record the above information about your tool. The information is available at Main Menu --> System Setup --> Tool Information.
CP9695 AutoScanner® Pro | User guide | 3 | en Table of Contents 1 4.10 4.11 4.12 4.13 4.14 Vehicle Selection. . . . . . . . . . . . . . . . . . . CodeConnect® Feature . . . . . . . . . . . . . . Code Criteria . . . . . . . . . . . . . . . . . . . . . . Acronyms. . . . . . . . . . . . . . . . . . . . . . . . . Component Locator. . . . . . . . . . . . . . . . . 20 21 22 22 23 5 Diagnostic Menu . . . . . . .
en | 4 | User guide | CP9695 AutoScanner® Pro 579999 | REV. A | 11.
CP9695 AutoScanner® Pro | User guide | 5 | en 1 Safety Precautions For your safety, read this manual thoroughly before operating your scan tool. Always refer to and follow safety messages and test procedures provided by the manufacturer of the vehicle or equipment being tested. The safety messages presented below and throughout this user’s manual are reminders to the operator to exercise extreme care when using this test instrument. 1.
en | 6 | User guide | CP9695 AutoScanner® Pro WARNING WARNING Risk of poisoning. • Use this scan tool in locations with mechanical ventilation providing at least 4 air changes per hour. Engine exhaust contains odorless gas which can be lethal. • Route the exhaust outside while testing with the engine running. Poisoning can result in death or serious injury. Risk of flying particles. • Safety goggles and protective gloves must be worn by the operator and any bystanders while using electrical equipment.
CP9695 AutoScanner® Pro | User guide | 7 | en WARNING CAUTION Engine compartment contains electrical connections and hot or moving parts. • Keep yourself, test leads, clothing and other objects clear of electrical connections and hot or moving engine parts. • Do not wear watches, rings, or loose fitting clothing when working in an engine compartment. • Do not place tools or test equipment on fenders or other places in engine compartment.
en | 8 | User guide | CP9695 AutoScanner® Pro 3 Getting Started 3.1 Introduction The scan tool was developed by experts in the automotive service industry to help diagnose vehicles and assist in troubleshooting procedures. The scan tool monitors vehicle events and retrieves codes from the vehicle’s control modules to help pinpoint problem areas.
CP9695 AutoScanner® Pro | User guide | 9 | en 1. OBD II Data Link Connector (DLC) Pins 1 8 2. 3. Bx = Body Cx = Chassis Px = Powertrain Ux = Network communication x - 0, 1, 2, or 3 Vehicle specific system Specific fault designation Example: P0101 = Mass or volume air flow circuit range/performance problem Powertrain Codes 9 1. 2. 3. 4. 5. 6. 7. 8. 9. 10. 11. 12. 13. 14. 15. 16. 3.
en | 1 0 | User guide | CP9695 AutoScanner® Pro 4.2 Specifications 4 Using the Scan Tool Display 4.1 The Scan Tool Storage Temperature -20 to 70°C (-4 to 158°F) Internal Power 4-AAA batteries External Power 7 to 16 Volts Color, backlit, QVGA resolution Operating Temperature 0 to 50°C (32 to 122°F) 1 A minimum of 8.0 V is required for most control modules to operate properly in a vehicle. 11 Dimensions 10 Height Width Depth 9 6.5 inches 165.1 mm 3.75 inches 95.25 mm 1.13 inches 28.
CP9695 AutoScanner® Pro | User guide | 11 | en 4.4 Power Internal Battery • Battery power is not required to use tool. • ON/OFF button on scan tool turns tool on and off. • Press and hold ON/OFF for at least 1 second to turn on scan tool. • The scan tool will automatically turn OFF after a user-selectable period of inactivity when powered from the internal batteries. The default is 2 minutes. • When powered from the internal batteries, the scan tool will dim display backlighting.
en | 1 2 | User guide | CP9695 AutoScanner® Pro Changing Auto-Power Off The Auto-Power Off feature allows the tool to turn off automatically after a selected amount of time when tool is not being used. The Auto-Power Off feature will only turn the tool off when it is operating on battery power. From System Setup screen: 1. Select Auto-Power Off. • Use the UP and DOWN keys until AutoPower Off is highlighted. • Press .
CP9695 AutoScanner® Pro | User guide | 13 | en Language Setup System Setup English Español Francais English/Metric Auto-Power Off Quick Test Print Header Language Setup Long PID Names Pre-Trigger Setup Tool Information Display Test 3. 2. Select desired Print Header choice. • Use the UP and DOWN keys until desired choice is highlighted. Print Header ON OFF 3. Save Language Setup setting. • Press . NOTE: When Spanish or French translation is not known, English will be shown.
en | 1 4 | User guide | CP9695 AutoScanner® Pro Pre-Trigger Setup This function is used to configure how many Pre-Trigger frames are stored prior to beginning a recording. Pre-Trigger frames are the negative frames when you are playing back a recording. From System Setup screen: 1. Select Pre-Trigger Setup. • Use the UP and DOWN keys until PreTrigger Setup is highlighted. • Press .
CP9695 AutoScanner® Pro | User guide | 15 | en System Setup English/Metric Auto-Power Off Quick Test Print Header Language Setup Long PID Names Pre-Trigger Setup Tool Information Display Test 2. 3. Start Display Test. • Press . Look for missing spots. • The first screen displayed says, “Check for missing spots in the display.” Display Test Check for spots in the display Press BACK to exit • Solid red, green, and blue screens are displayed. • 4.
en | 1 6 | User guide | CP9695 AutoScanner® Pro –– System Setup –– –– Quick Test Print Header Language Setup Long PID Names Pre-Trigger Setup Tool Information Display Test Keypad Test Memory Test 2. Memory Test INT RAM INT FLASH Press a key. • Key name or scroll direction should inverse colors on display. • will return the tool to the System Setup screen. Keypad Test F1 F2 F3 F4 CODE BACK If no problems were detected, then “Passed” is displayed. If RAM fails, an error message is shown.
CP9695 AutoScanner® Pro | User guide | 17 | en 1. Select Review Data. • Use the UP and DOWN keys until Review Data is highlighted. • Press . Main Menu Vehicle Diagnostics Acronyms Review Data Print Data Code Lookup System Setup If Review Data is selected from the Main Menu, a Select Vehicle menu is shown. This menu contains up to 5 previous vehicles, so select which vehicle you wish to review data. Select Vehicle Prev: 06 Accord Prev: 04 Express 1500 From the Review Data menu: 1. Select Recording.
en | 1 8 | User guide | CP9695 AutoScanner® Pro –– If graphing is available for selected PID, the 1. • • “ ” icon is located on the side of the screen. –– Press to select PIDS to graph. –– Use the UP and DOWN arrow keys to highlight the second PID to graph and then press the RIGHT arrow to select. A maximum of two PIDs can be graphed. Press to see graph. The triangle below the graph indicates the position of the frame in the graph.
CP9695 AutoScanner® Pro | User guide | 19 | en 4.7 Code Lookup Code Lookup is used to look up definitions of DTCs stored in the scan tool. • If Code Lookup is selected from the Main Menu, the tool will display Vehicle Selection. Selecting a vehicle in Code Lookup from the Main Menu does not change the current (previously selected) vehicle. It is only a temporary change to allow you to lookup DTC for a vehicle other than the previous vehicle.
en | 2 0 | User guide | CP9695 AutoScanner® Pro 3. 4. 5. 6. 7. Turn the ignition switch to the ON position. Do not start the engine. Plug the OBDII connector attached to the Tool into the Data Link Connector. The tool will attempt to identify the vehicle. If successful, the vehicle identified will be displayed. If vehicle couldn‘t be identified, menus will be shown for you to select the vehicle manually. The tool can support up to 5 previous vehicles in the garage.
CP9695 AutoScanner® Pro | User guide | 21 | en Garage Full Vehicle? Prev: Prev: Prev: Prev: Prev: OBDII/EOBD US Europe Asia Prev: 06 Accord Prev: 04 Express 1500 Prev: 04 Express 1500 Prev: 04 Express 1500 Turn Key Off Please turn the key off for 10 seconds then turn the key on. Press ENTER to continue • If vehicle power is not detected, a screen is shown to verify tool connection. Vehicle Required Please verify the tool is connected to the vehicle with the ignition key turned on.
en | 2 2 | User guide | CP9695 AutoScanner® Pro Frequently Reported Fix As likely as other solutions Also Reported Fix Less likely than other solutions provided, but worth considering. P0102 1/2 ECM $10 3. 4. Mass Or Volume Air Flow A Circuit Low Input If a vehicle has multiple sets of criteria for the DTC, a menu is displayed, so that the tool can provide the most accurate criteria for your specific vehicle. Use the UP and DOWN keys to scroll one line at a time.
CP9695 AutoScanner® Pro | User guide | 23 | en • • Use the UP and DOWN keys until the desired acronym is highlighted. Press . component. • Use the UP and DOWN keys until the desired group range is highlighted. • Press . Acronyms Component Locator # Of Emiss # Of Pwrt #CMP/CKP LOSS #TRP SNC MISF #TRPS SNC MISF % Alcohol % GRADE % METHANOL % of Pdl 4. View selected acronym. • Press to return to the Diagnostic Menu. A - Fuel Injector (No 4 Fuel Injector (No 5 - K M - W 3.
en | 2 4 | User guide | CP9695 AutoScanner® Pro The scan tool keeps data received from the previous 5 vehicle’s selected until any of the following occurs: • A new vehicle is selected when you already have 5 in your garage forcing you to select which vehicle you want to remove from your garage to create space. • Scan tool is flash programmed to update software. On initial link to vehicle, scan tool checks the status of I/M Monitors no matter which function is selected.
CP9695 AutoScanner® Pro | User guide | 25 | en Global OBDII Functions I/M Monitors Drive Cycle Monitor State OBD Check MIL Status O2 Monitor Tests Diagnostic Monitor Tests On-Board Systems Vehicle Information Modules Present Two types of I/M Monitors test are: • Since DTCs Cleared - shows status of the monitors since the DTCs were last erased. • This Drive Cycle - shows status of monitors since the start of the current drive cycle.
en | 2 6 | User guide | CP9695 AutoScanner® Pro DTC Description - This area is reserved for the text describing the trouble code listed in the DTC number field. DTC Type - This area is reserved for providing additional information about the DTC. Multiple DTC types may be possible for a given DTC number. Not all vehicles support DTC types. This table describes possible DTC types.
CP9695 AutoScanner® Pro | User guide | 27 | en In this example, module (MOD) $18 is reporting the DTCs. P0113 P2270 1/3 Mod $18 1/3 Eng $10 Torque Converter Clutch Circuit High Intake Air Temperature Sensor 1 Circuit High Input Read Read Erase FFrame In this example, the Engine Module is reporting a History Code. The $10 is the engine module address. P2270 Erase FFrame The screen below shows dashes for the DTC number and a MIL code of 213.
en | 2 8 | User guide | CP9695 AutoScanner® Pro 1. Select Erase Codes. • Use the UP and DOWN keys until Erase Codes is highlighted. • Press . • • Select Module Diagnostic Codes OBDII/EOBD Engine ABS Airbag Read Codes Erase Codes View Freeze Data Component Locator Acronyms Review Data Print Data Code Lookup System Setup 4. • Use the UP and DOWN keys until the desired choice is highlighted. Press . If diagnostic results and codes are not to be erased select NO and press .
CP9695 AutoScanner® Pro | User guide | 29 | en Global OBDII Functions MIL is ON I/M Monitors Drive Cycle Monitor State OBD Check MIL Status O2 Monitor Tests Diagnostic Monitor Tests On-Board Systems Vehicle Information Oil Light Reset MIL lamp should be ON if engine is running Press ENTER to continue 2. View State OBD Check display.
en | 3 0 | User guide | CP9695 AutoScanner® Pro 2. Observe while the scan tool validates PID MAP. • PID MAP validation is the tool asking the vehicle which PIDs are supported. See Appendix A for a complete list of PIDs supported by the tool. • Multiple PIDs may be sent if vehicle is equipped with more than one computer module (for example a powertrain control module [PCM] and a transmission control module [TCM]). The scan tool identifies them by their identification names (ID) assigned by manufacturer (i.
CP9695 AutoScanner® Pro | User guide | 31 | en Select Data to View ABS TPS B(%) MIL STATUS Entire Data List Custom Data List English/Metric 0.0 Off Throttle Position B 2. Select View Instructions or Not. • Use the LEFT and RIGHT keys. • Press . Custom Setup Do you want to view instructions for creating a custom data list? Yes 3. No Select PIDs to View. • Use the UP and DOWN keys to move up and down list. • The RIGHT arrow selects or deselects data parameter.
en | 3 2 | User guide | CP9695 AutoScanner® Pro Validating PIDs Record Data Validating PID List Playback data? PID 116/329 Yes Please Wait 3. Refer to View Data to setup Custom List or View Entire List and Pre-Trigger Setup to set the number of frames to keep prior to triggering the recording. Select Data to Record Entire Data List Custom Data List Pre-Trigger Setup 4. Press to begin recording. • Data continues to be saved until either: –– Record memory is full. –– Operator presses .
CP9695 AutoScanner® Pro | User guide | 33 | en TROUB CODE FUEL SYS 1 FUEL SYS 2 CALC LOAD(%) COOLANT (°F) ST FTRM1(%) LT FTRM1(%) MAP(”HG) ENG SPEED(RPM) VEH SPEED(MPH) P2122 N/A N/A 0.0 -40 0.0 0.0 28.1 0 0 From Global OBDII Functions Menu: 1. Select Drive Cycle Monitor. • Use the UP and DOWN keys until Drive Cycle Monitor is highlighted. • Press .
en | 3 4 | User guide | CP9695 AutoScanner® Pro • Since DTCs Cleared Misfire Monitor Fuel System Mon Comp Component Catalyst Mon Htd Catalyst Evap System Mon Sec Air System A/C Refrig Mon Oxygen Sens Mon • • ok ok ok ok n/a inc n/a n/a ok The scan tool display is continuously updated. Monitors that are “ok” will disappear and only the “inc” monitors will remain displayed. Monitors designated “n/a” are not displayed.
CP9695 AutoScanner® Pro | User guide | 35 | en • 3. The O2 sensors located upstream (before catalyst) may perform differently than ones located downstream (after catalyst). • Test IDs are shown for unknown O2 sensor tests. View results of selection. • Use the UP and DOWN keys. Select Diag Mon Test Test Test Test Test Test Test Test Test Test O2 Bank1 Sensor1 4. 5.
en | 3 6 | User guide | CP9695 AutoScanner® Pro O2 Sensor B1S1 RICH-LN Thresh MOD MAX MEAS MIN STS 3. 4. $07 0.4497(V) 0.4497(V) 0.4497(V) OK Return to Select Test menu. • Press . Return to Global OBDII Functions Menu. • Press . 5.12 On-Board Systems On-Board Systems The On-Board Systems test allows the scan tool to control operation of vehicle components, tests or systems. • Some manufacturers do not allow tools to control vehicle systems.
CP9695 AutoScanner® Pro | User guide | 37 | en Vehicle Information Global OBDII Functions I/M Monitors Drive Cycle Monitor State OBD Check MIL Status O2 Monitor Tests Diagnostic Monitor Tests On-Board Systems Vehicle Information Oil Light Reset Retrieving CALID data. It may take up to 1.5 minutes. Press BACK to exit Vehicle Information Vehicle Information Verify key ON Engine OFF. Retrieving IPT data. It may take up to 1.5 minutes. Press ENTER to continue Press BACK to exit WORKING 2.
en | 3 8 | User guide | CP9695 AutoScanner® Pro Sensor Monitor Completion Counts O2SCOMPX O2 Bank x Sensor Conditions Encountered O2SCONDX O2 Counts Bank x Monitor Completion Condition EGRCOMP EGR Counts Monitor Conditions Encountered EGRCOND EGR Counts AIR Monitor Completion Condition AIRCOMP Counts (Secondary Air) AIR Monitor Conditions Encountered AIRCOND Counts (Secondary Air) Monitor Completion Condition EVAPCOMP EVAP Counts Monitor Conditions Encountered EVAPCOND EVAP Counts VIN (MOD $09) 1HGCM56866
CP9695 AutoScanner® Pro | User guide | 39 | en Oil Light Reset Cycle key, Turn engine off, Key on Press BACK to exit Press ENTER to continue 3. battery) or a battery with a different capacity (mAh), the vehicle may require reprogramming to the new battery type in addition to performing the battery reset. Reprogramming is not a function of the tool. Consult the vehicle manual for additional vehicle-specific information. From the Battery/Charging Services Menu: 1. Select Battery Reset.
en | 4 0 | User guide | CP9695 AutoScanner® Pro Battery Reset Charging System Monitor Battery System Reset Complete DLC KOEO Voltage: 12.2V Please start the engine Press ENTER to continue 5.16 Charging System Monitor Press BACK to exit 4. The Charging System Monitor function allows the scan tool to provide voltage measurements at the DLC to give an indication of battery, starter, and alternator performance. From the Special Functions Menu: 1. Select Charging System Monitor.
CP9695 AutoScanner® Pro | User guide | 41 | en Test Results DLC KOEO Voltage DLC Cranking Voltage DLC KOER Voltage Global OBDII Functions 12.2 10.4 14.7 O2 Monitor Tests Diagnostic Monitor Tests On-Board Systems Vehicle Information Oil Light Reset Charging System Monitor Modules Present Component Locator Acronyms ess ENTER to view the data plot. On the first screen, the scan tool didn’t detect that the engine had started, so there isn’t a KOER voltage reading.
en | 4 2 | User guide | CP9695 AutoScanner® Pro Since CAN vehicles use module IDs larger than 2 digits, the scan tool assigns a 2 digit module ID to be used in place of the actual CAN module ID. The module ID assigned for the CAN module ID is used in all functions of the scan tool. • ISO 14230-4 protocol is shown as K2K (Keyword 2000). 2. The scan tool will now calculate Fuel Consumption.
CP9695 AutoScanner® Pro | User guide | 43 | en P0113 On Demand Tests KOEO On Demand KOEO Output State KOER On Demand Component Locator Acronyms Review Data Print Data Code Lookup System Setup Intake Air Temperature Sensor 1 Circuit High Input FORD KOEO CODES Read 5. 2. 3. Perform the following: • Set parking brake. • Transmission in park (P) or neutral (N). • Turn A/C off. • Start engine and let idle until hot. • Turn ignition key off. • Wait 10 seconds. Turn key on engine off. Do not start engine.
en | 4 4 | User guide | CP9695 AutoScanner® Pro KOEO Injector Buzz KOEO Output State All But Fans/Injectors Low Speed Fan High Speed Fan Test is running. Time remaining 2:59 Please Wait 4. Return to the On Demand Tests Menu. • Press . 5.21 KOEO Output State The KOEO Output State tests the output devices (such as actuators or relays) controlled by the Ford PCM by powering them on and off. The voltage and outputs on suspect devices can be measured and recorded using a voltmeter.
CP9695 AutoScanner® Pro | User guide | 45 | en P1127 CAUTION Keep hands and tools away from fan and engine during test. Heated Oxygen Sensor Downstream Sensor Not Tested FORD KOER ON DEMAND IMPORTANT Perform each step when prompted by the Scan Tool. Failure to follow directions may set DTC(s) in the PCM. 3. Follow the instructions displayed on the tool. If the steps are not followed correctly, a message displays asking you to RETRY. • Set parking brake. • Transmission in park (P) or neutral (N).
en | 4 6 | User guide | CP9695 AutoScanner® Pro 3. If no DTCs are present, a message stating “No Codes Found” is displayed. View and write down DTCs. • Use the UP and DOWN keys. P0340 On Demand Tests KOEO On Demand KOEO Injector Buzz KOEO Output State KOER On Demand KOER Glow Plug KOER Cylinder Contribution Component Locator Acronyms Review Data 1/4 ECM $10 Camshaft Position Sensor A Circuit (Bank 1 Or Single Sensor) FORD GLOWPLUG CODES 2. 4. Return to the On Demand Tests Menu. • Press . 5.
CP9695 AutoScanner® Pro | User guide | 47 | en • • 6.2 With the key on engine off (KOEO), verify vehicle battery voltage is at least 8.0V. Verify the control module is not defective. Refer to the service manual to diagnose the control module. LINK ERROR Check connection! Try again? Scan Tool Does Not Power Up WARNING Review Safety Messages on page 5 before troubleshooting.
en | 4 8 | User guide | CP9695 AutoScanner® Pro PID PID Description ABS FRP ABS LOAD ABS TPS B, C ABSLT TPS ACC POS D ACC POS REL AECD1_TIME1, TIME 2 AECD10_TIME1, TIME 2 AECD11_TIME1, TIME 2 AECD12_TIME1, TIME 2 AECD13_TIME1, TIME 2 AECD14_TIME1, TIME 2 AECD15_TIME1, TIME 2 AECD16_TIME1, TIME 2 AECD17_TIME1, TIME 2 AECD18_TIME1, TIME 2 AECD19_TIME1, TIME 2 AECD2_TIME1, TIME 2 AECD20_TIME1, TIME 2 AECD3_TIME1, TIME 2 AECD4_TIME1, TIME 2 AECD5_TIME1, TIME 2 AECD6_TIME1, TIME 2 AECD7_TIME1, TIME 2 AECD8_TI
CP9695 AutoScanner® Pro | User guide | 49 | en PID PID Description EP_1, 2 Exhaust Pressure Sensor Bank 1, Bank 2 Equivalence Ratio Commanded EVAP Purge EVAP Vapor Pressure Absolute EVAP Vapor Pressure Fuel Rail Pressure A, B EQ RATIO EVAP PURGE EVAP VP EVAP VPA FRP_A, B FRP_A_CMD, B_ CMD FRT_A, B FUEL LEVEL FUEL PRES FUEL SYS 1, 2 FUEL TYPE FUEL_RATE FUEL_TIMING GPL_STAT IAF_A_CMD, B_ CMD IAF_A_REL, B_ REL IAT IAT 11, 21 IAT 12, 22 IAT 13, 23 ICP_A, B ICP_A_CMD, B_ CMD IDLE_TIME IGN ADV LAMBDA11, 21 L
en | 5 0 | User guide | CP9695 AutoScanner® Pro PID PID Description SECOND AIR ST FTRM ST FTRM1, 3 ST FTRM2, 4 ST SEC FT1, 2, 3, 4 TAC_A_CMD, B_ CMD TAC_A_REL, B_ REL TCA_CINP, TCB_ CINP TCA_CINT, TCB_ CINT TCA_COUTT, TCB_COUTT TCA_RPM, TCB_ RPM TCA_TOUTT, TCB_TOUTT TCA_TINT, TCB_ TINT THROT CMD TP G TQ_ACT Secondary Air Status Fuel Trim Bank / Sensor Short Term Fuel Trim1 or 3 Short Term Fuel Trim2 or 4 Short Term Secondary O2 Sensor Fuel Trim 1, 2, 3, 4 Commanded Throttle Actuator A Control, B Control
CP9695 AutoScanner® Pro | User guide | 51 | en disengage cruise control systems and torque converter clutch (TCC) solenoids. See also TCC. CAM: Camshaft position sensor. Sends a frequency signal to the PCM to synchronize fuel injector and spark plug firing. Catalytic converter: Designed to reduce exhaust emissions. CAN: Controller area network CARB: California air resources board. Governing body for emissions control in California. CKP REF: Crankshaft position reference. CKP: Crankshaft position. See CPS.
en | 5 2 | User guide | CP9695 AutoScanner® Pro ture, engine load, vehicle speed, Park/Neutral switch position, and knock sensor condition. EVAP: Evaporative emissions system FC: Fan control Freeze frame: A block of memory containing DTCs of the vehicle operating conditions for a specific time. FTP: Federal test procedure. Strict test of vehicle’s emissions. Ground (GND): An electrical conductor used as a common return for an electric circuit(s) and with a relative zero potential (voltage).
CP9695 AutoScanner® Pro | User guide | 53 | en upstream and downstream of the catalytic converter. The PCM uses these sensors to fine tune the air-fuel ratio and to monitor the efficiency of the catalytic converter. See Bank 1, Bank 2, Sensor 1, Sensor 2. OBDII: On-board diagnostics, second generation. OBD II is a U.S. Government-mandated standard requiring all cars and light trucks to have a common data connector, connector location, communication protocol, DTCs and code definitions.
en | 5 4 | User guide | CP9695 AutoScanner® Pro Throttle body injection. A fuel injection system having one or more injectors mounted in a centrally located throttle body, as opposed to positioning the injectors close to an intake valve port. TBI is also called Central Fuel Injection (CFI) in some vehicles. TCC: Torque converter clutch TCM: Transmission control module TCS: Traction control system for PCM and brakes TDC: Top dead center. When a piston is at its uppermost position in the cylinder.
CP9695 AutoScanner® Pro | User guide | 55 | en 9 Limited Warranty THIS WARRANTY IS EXPRESSLY LIMITED TO ORIGINAL RETAIL BUYERS OF BOSCH ELECTRONIC DIAGNOSTIC TOOLS (“UNITS”). BOSCH Automotive Service Solutions LLC Units are warranted against defects in materials and workmanship for one year (12 months) from date of delivery.
Bosch Automotive Service Solutions Inc. 3000 Apollo Drive Brook Park, OH 44142 USA Telephone 1-800-228-7667 www.actron.
