User Guide
Table Of Contents
- 1 Safety Precautions
- 1.1 Read All Instructions
- 2 Important Safety Warnings and Instructions
- 3 Getting Started
- 4 Using the Scan Tool
- 5 Diagnostic Menu
- 5.1 I/M Monitors (Emissions)
- 5.2 Read Codes
- 5.3 Erase Codes
- 5.4 MIL Status
- 5.5 State OBD Check
- 5.6 View Data
- 5.7 Record Data
- 5.8 View Freeze Data
- 5.9 Drive Cycle Monitor
- 5.10 O2 Monitor Tests
- 5.11 Diagnostic Monitor Tests
- 5.12 On-Board Systems
- 5.13 Vehicle Information
- 5.14 Oil Light Reset
- 5.15 Battery Reset
- 5.16 Charging System Monitor
- 5.17 Modules Present
- 6 Troubleshooting
- 7 Appendix A— PID Definitions
- 8 Appendix B—Glossary
- 9 Limited Warranty
en
|
18
|
User guide
| CP9680
AutoScanner® Plus
573102 | REV. B | 03.2016
Bosch Automotive Service Solutions Inc.
ABSLT TPS(%)
CALC LOAD(%)
COOLANT(°F)
ENG SPEED(RPM)
FUEL SYS 1
FUEL SYS 2
IAT(°F)
IGN ADV(°)
LT FTRM1(%)
0.0
3.5
95
692
OPEN
OPEN
75
4.5
3.1
Frame:
Throttle position
Time: 0.00
– If graphing is available for selected PID, the
“ ” icon is located on the side of the
screen.
– Press to select PIDS to graph.
– Use the UP and DOWN arrow keys
to highlight the second PID to graph
and then press the RIGHT arrow to
select. A maximum of two PIDs can be
graphed. Press to see graph.
• The triangle below the graph indicates the
position of the frame in the graph.
– Use the LEFT and RIGHT arrow keys to
scroll back and forth through graph.
– Use the UP and DOWN keys to toggle
back and forth between PIDs.
• Different vehicles communicate at different
speeds and support a different number of PIDs.
Therefore, the maximum number of frames that
can be recorded varies.
Select PIDs to Graph
ABSLT TPS(%)
✓CALC LOAD(%)
COOLANT(°F)
ENG SPEED(RPM)
IAT(°F)
MAF(LB/M)
MAP(”HG)
VEH SPEED(MPH)
Calculated Engine Load
CALC LOAD(%)
19.4
17.5
Frame: Time:
21 26.8
19.2
3. Return to Review Data menu.
• Press .
Print Data
The Print Data function allows the printing of diagnostic
information stored in the Scan Tool.
• The Scan Tool’s internal battery power can be
used to print data.
• Use the Print Data function to turn On/Off
printing vehicle information prior to printing
data.
• Make sure you have previously installed the PC
software in Download Scanning Suite.
• Launch Scanning Suite and then start printing
application.
• Follow all instructions on PC.
1. Select Print Data.
• Use the UP and DOWN keys until Print
Data is highlighted.
• Press .
Main Menu
Vehicle Diagnostics
Acronyms
Review Data
Print Data
Code Lookup
System Setup
Print Data
Press ENTER to continue
Launch PC printing software
application.
• On the Print Data menu, Print All prints all data
collected by the Scan Tool.
Print Data
✓Print All
✓I/M Monitiors
✓DTCs (Codes)
State OBD Check
Recording
View Freeze Data
O2 Monitor Tests
Diagnostic Monitor Tests
Vehicle Information
• When printing a Recording, Start Frame and End
Frame need to be defined.
2. Select Data to Be Printed.