R EP-550™/EP-650™ Inversion Table Assembly Instructions R HANG TE 5 YEAR RANT Y W AR S UP TE E www.ActiveForever.
BEFORE YOU BEGIN: Review all steps before beginning assembly and read all precautions before using the inversion table. Carefully adhere to the Assembly Instructions and Owner’s Manual to help ensure safety and product integrity. IMPORTANT SAFETY INSTRUCTIONS READ ALL INSTRUCTIONS BEFORE USING THE INVERSION TABLE.
Items for Assembly Carefully remove the individual parts from the carton. You should have all of the items listed below. If any items are missing or damaged, contact Customer Service at 1-800-847-0143.
Before Beginning Table Bed Before reading further, study the drawing below to familiarize yourself with the important components of your new Teeter Hang Ups® inversion table.
Step 1 Right spreader arms Left Crossbar back front Figure 1 Figure 2 Assemble the A-frame Base (F7-1002) and Install the Handles (F5-1069) • Open the A-frame and make sure the spreader arms are locked, rest the A-frame on the floor (Figure 1). The Crossbar is at the front. • Place each Hand Grip (left/right) over the outside edge of the corresponding Hinge Plate (Figure 2). • Insert three 1/2” (13mm) hex bolts (H1-1202) through the hinge plate into each Hand Grip.
Step 2 Support Beam Figure 3 Figure 4 Upper Support Arms Attach the Upper Support Arms to the Table Bed (EP-1140) • Before following this step, make sure you have read the orange insert that came attached to the Table Bed. • Place the Table Bed face down on the floor and push down on the Support Beam, so the two holes align evenly with holes at the base of Upper Support Arms (Figure 3). You may have to exert extra pressure to ensure the Support Beam slides over the rubber spacers.
Step 3 Install the Roller Hinges (F5-1064) onto the Table Bed (EP-1140) • For ease-of-assembly, rest the Table Bed against the side of the A-frame (Figure 5). • Open the Cam Locks on each side of the Table Bed (Figure 5A). • With the Pivot Pins facing outward, insert the Roller Hinges into the brackets on each side of the Table Bed. The Roller Hinges must slide between the Cam Locks and the brackets. • Make sure the Roller Hinges are in the same hole setting on both sides.
Step 4 Attach the Table Bed (EP-1140) to the A-frame (F7-1002) • Holding each side near the Roller Hinges, pick up the Table Bed and stand at the front of the A-frame where the Crossbar is located. Lower each Pivot Pin into the A-frame hinge plates one at a time (Figure 7). You may need to push outward on the A-frame in order to slide the second Pivot Pin into the hinge. Figure 8 shows the correct placement of the Pivot Pin into the hinge plate.
Step 5 Insert the Main Shaft (EP-1120) into the Table Bed (EP-1140) • Loosen the De-rattler knob on the Main Shaft Housing. • With the height adjustment settings on the Main Shaft facing up, slide the end of the Main Shaft into the Main Shaft Housing on the Table Bed. • Pull out the height-selector locking pin to allow the Main Shaft to slide in farther (Figure 10).
Step 6 Install the Front Foam Rollers (F5-1051) • Slide the Foam rollers over each side of the Front Ankle Bar (Figures 12 and 12A). • Figure 12 Figure 12A Insert the black plugs (F5-1056) into each open end of the Front Ankle Bar if they are not already assembled.
Step 7 Attach the Tether Strap (F5-1007) to Limit the Degree of Rotation • Hook the clip at the end of the tether strap to the loop at the base of the table bed (Figure 13) to limit your degree of rotation. • Tighten or loosen the strap to restrict or extend your angle of rotation. Attach the Head Pillow • Figure 13 Figure 14 Attach the Head Pillow by securing the Velcro straps through the holes in the Table Bed – the position of the pillow can be adjusted depending on the user (Figure 14).
Step 8 Before Use • Test the table by hand for smooth and steady rotation (Figure 15). • Ensure that all fasteners are secure. • Please complete the warranty registration online • For your reference, the serial number can be found on the back of the Table Bed. ! WARNING Read the Owner’s Manual thoroughly before using your Teeter Hang Ups Inversion Table.
Adjustments / Maintenance / Storage CHANGING THE ROLLER HINGE SETTING Figure 16 A B C • Stand with your legs on either side of the Main Shaft. • Reach under each Roller Hinge with your index fingers. Use your thumbs to release the locks over the Roller Hinges (See Figure 16). • Lift both sides of the table out of the A-frame at the same time. You may rest the table on the Crossbar of the A-frame. • Unlock the Cam Locks for each Roller Hinge.
