RemRest™ Tiers 1-3 900 Series Patient Manual CAUTION: USA Federal law restricts this device to sale by or on the order of a physician. 21148 Rev.
Table of Contents SIZE 4.7" H X 8.6" W X 9.4" D 11.9cm H x 21.8cm W x 23.9cm D WEIGHT <5lb 2.3kg Specifications 2 Introduction 3 IEC Symbols 4 System Components 5 Instructions for Use 6 PRESSURE RANGE 3.
Introduction In 1993, the National Commission on Sleep Disorders Research stated that as many as 18 million Americans may have signs and symptoms of Obstructive Sleep Apnea (OSA). OSA is a condition where the upper airway relaxes during sleep causing the airway to obstruct. Apnea is a word meaning “without breath.” People diagnosed with OSA stop breathing repeatedly during sleep which can result in extreme exhaustion and damage to vital organs.
IEC Symbols Equipment Classification with respect to protection from electric shock: Class II Degree of protection from electric shock: Type BF Degree of protection against ingress of liquids: Ordinary Equipment not suitable for use in the presence of flammable anaesthetic mixture with air or with nitrous oxide.
System Components RemRest 5
Instructions For Use IMPORTANT SAFEGUARDS Follow all basic safety precautions. Please read instructions before using. Precautions are not limited to the safety information provided. Important information is highlighted as indicated: WARNING Important safety information for hazards that might cause serious injury. CAUTION Important information to prevent damage to the device. NOTE Information requiring special attention.
Save These Instructions The RemRest system consists of a CPAP flow generator, tubing and a nasal interface. Other accessories may be used and are available as needed from your care provider. Comfortable fit is very important. Please discuss with your care provider to determine the best nasal interface that will meet your needs. WARNING Do not under any circumstances plug any vent holes on your mask. These are for proper exhaling and plugging them might cause carbon dioxide buildup.
air for longer than several minutes can in some circumstances lead to suffocation. This warning applies to most models of CPAP units. CAUTION At low CPAP pressures, the flow through the exhalation port may be inadequate to clear all exhaled gas from the tubing. Some rebreathing may occur. This warning applies to devices with rebreathing testing which demonstrates that rebreathing may occur at low pressures within the operating pressure range of the device.
RemRest Flow Generator Operation • Place the RemRest device on a flat, sturdy surface with the back of the unit away from heating vents, radiators, curtains and other objects that could restrict air intake. • Secure the mask, connect the tubing, and prepare any accessories you might use prior to operation of the RemRest device. It is recommended that the device be left plugged in when not in use. This is especially helpful for Tier 2 and 3.
3. The two green lights (on/off light and ramp light) will turn on for two seconds then will remain off until the motor/blower is turned on and/or the ramp function is turned on. If the ramp function was used the last time the device was operated, then the ramp light will stay on. ON/OFF LIGHT RAMP LIGHT 4. To turn on a Tier 1 device, press the on/off button. The on/off light will turn on and the CPAP device will accelerate to its prescription air pressure setting.
5. If the ramp function is not already set, simply pushing the ramp button on once the unit is running will not start the ramp function. To initiate the ramp function: • If the device motor is running, turn off the device by pushing on/off button (ramp light and on/off light turn off) • Push the ramp button on (ramp light turn on) • Turn ON the device by pushing on/off button (ramp light and on/off light on).
motor vehicle or recreational vehicle, insert the plug into the DC jack located on the back of the CPAP and plug the other end into the vehicle’s 12V DC outlet. 3. The green light (on/off light) will turn on for two seconds then will remain off until the motor/blower is turned on. The LCD will also turn on completely (as shown in Symbols Definition section on page 13) for 2 seconds and will then switch to display the prescription pressure.
SYMBOL DEFINITIONS 4 LOW Used in technician/dealer mode only HI Used in technician/dealer mode only TIME Used in the technician/dealer mode only USE Used in the technician/dealer mode only RAMP Icon will flash during ramp setting or will stay on once ramp is set and the ramp mode is in use RUN The display will show the time the motor/blower has been running.
• In the ramp mode, the display will show the increasing pressure until the prescription pressure is reached. Your physician may have prescribed a specific ramp time. In this case, do not attempt to adjust the ramp setting or operating the unit without the ramp function turned on without consulting your physician. 5. If the ramp function is not already set, changing the ramp setting to “ON” while the CPAP device is running will not start the ramp function.
7. To view the “data code”, push and hold the MODE button for three seconds, a code will show up on the display for five seconds and the on/off light will flash. No other icons will turn on. After five seconds, the display will return to the prescribed pressure setting and the on/off light will stop flashing. 8. Turn OFF the device (the on/off light will turn off and the motor/blower will stop running). The display will remain on, if the device remains plugged in.
RemRest Care REMREST CLEANING To clean the RemRest device, turn OFF the unit and unplug it from the power source. Using a damp cloth, wipe the unit clean making sure no liquids enter the device itself. Allow the unit to completely dry prior to using. REMREST INLET FILTER The RemRest filter is located on the back of the device and is reusable. To make sure your device continues to provide optimum performance, check your filter weekly and clean the filter once per month (or sooner if dirty).
MASKS, NASAL INTERFACES, TUBING AND HEADGEAR Consult the user instructions provided with the accessories to determine the recommended cleaning method. Otherwise, these items may be washed as needed. To clean, remove the tubing and headgear from the nasal interfaces. Using a solution of warm water and mild dishwashing detergent such as Dawn™, wash each item individually, rinse with clean, warm tap water and allow the accessory to air dry before using.
Troubleshooting Problem Unit wi not run No air comes out whi e the unit is on Possible Causes Unit not p ugged into a “ ive” out et P ug unit into a “ ive” out et Power cord not connected proper y Firm y attach AC or DC cord Air fi ter is p ugged C ean or rep ace the fi ter Air in et is b ocked Remove obstruction or reposition the unit so the in et is not b ocked. F exib e hose not connected to device. Connect f exib e hose to device.
Problem Irritated skin where mask meets the face Possible Causes Remedies Headgear is too tight Loosen the headgear Poor mask fit Contact your dealer Allergic reaction to mask material Try a different material or use a barrier between the mask and face.
Travel Information A carry bag is provided with the RemRest system and is suitable for carrying the unit and most accessories you might have. This bag is to be used as carry-on luggage only. Damage might occur to the unit if checked as regular luggage. RemRest is suitable for operation in most electrical power environments ranging from 100 to 240 Volts of alternating current (VAC), 50 and 60 Hertz or 12V DC when using the DC power cord.
Safety OXYGEN SAFETY Oxygen is a prescription drug and should only be administered under the supervision of a physician. Oxygen supports combustion. To avoid possible physical injury do not smoke or place the device near any heat source while using your CPAP with oxygen. WARNING If oxygen is used with this CPAP machine, the oxygen flow must be turned off when the CPAP machine is not operating.
ELECTRICAL SAFETY Do not submerse this product in water under any circumstances. Place this product away from the reach of children. FOLLOW ALL BASIC SAFETY PRECAUTIONS. PRECAUTIONS ARE NOT LIMITED TO THE SAFETY INFORMATION PROVIDED. Warranty NOTE There is no other express warranty.
Notes RemRest 23
MDSS GmbH Schiffgraben 41 30175 Hannover, Germany EC REP
