INSTALLATION AND OPERATING INSTRUCTIONS PATRIOT PORTABLE LIFT TM *450 LB. MAXIMUM CAPACITY (PRO POOL LIFT) MANDATORY – LEAVE THIS MANUAL WITH LIFT OWNER WARNING 1. 2. 3. 4. 5. 6. 7. 8. IMPORTANT SAFETY INSTRUCTIONS READ AND FOLLOW ALL INSTRUCTIONS. LIFT SAFETY CAN ONLY BE ENSURED IF THE LIFT IS INSTALLED AND OPERATED PROPERLY – AS PER INSTRUCTIONS. WARNING- TO REDUCE RISK OF INJURY, DO NOT PERMIT CHILDREN TO USE THIS PRODUCT UNLESS THEY ARE CLOSELY SUPERVISED AT ALL TIMES.
PATRIOT PORTABLE LIFT TABLE OF CONTENTS PAGE DESCRIPTION 3 ADA INSTALLATION GUIDELINES 4 PATRIOT PORTABLE PACKING LIST 5 PATRIOT PORTABLE ASSEMBLY INSTRUCTIONS 6-7 TRANSPORTING & USING THE PATRIOT PORTABLE 8 24V BATTERY OP & INSTALL INSTRUCTIONS 9 BATTERY MAINTENANCE 10 PRO POOL LIFT OPERATING INSTRUCTIONS 11 PRO POOL HEADREST (OPTIONAL) 12 CARE OF YOUR LIFT 13-15 TROUBLESHOOTING GUIDE 16 PRO POOL LIFT: PARTS LIST 17 SEAT ASSEMBLY: PARTS LIST 18 PATRIOT PORTABLE: PARTS LIST 19 W
INSTALLATION: ADA GUIDELINES ADA REQUIREMENTS: The PATRIOT PORTABLE LIFTTM is designed and manufactured to be 100% ADA compliant. But for the installed lift to be 100% compliant the installation must meet the requirement for CLEAR DECK SPACE as shown in the diagram to the left. To be compliant, install the lift at 16 inches [406mm] from the pool edge to the centerline of the seat, and make sure the deck has the required CLEAR DECK SPACE as shown.
THE PATRIOT PORTABLE LIFTTM WARNING 1. NEVER OPERATE THIS LIFT IF THE POOL DECK TO WATER LEVELEXCEEDS12” 2. BEFORE OPERATING THE LIFT THE 10 SUPPLIED WEIGHT PLATES MUST BE INSTALLED INSIDE THE COVER AS PER THESE INSTRUCTIONS. 3. THE 24V BATTERY WILL ARRIVE UNCHARGED FOR SAFETY. CHARGE THE BATTERY FOR 24 HOURS BEFORE INITIAL USE. PARTS LIST: (SEE FIGURE 7) 1. PORTABLE KIT MAIN FRAME W/ WHEELS 2. HARDWARE BAG 3. TOP WEIGHT STACK COVER W/ HANDLE 4. WEIGHTS HARDWARE BAG –PORTABLE KIT ITEM # QTY.
PATRIOT PORTABLE - ASSEMBLY INSTRUCTIONS 1. Begin by placing the parts from the previous page at or near to the desired poolside location. 2. Stack 10 supplied weight plates on the portable platform. To ensure proper alignment stack 3 to 4 plates, check alignment by temporarily putting the cover on, remove the cover and then stack 3 to 4 more plates. Repeat until all 10 weight plates are on the platform and properly aligned. 3.
TRANSPORTING & USING THE PATRIOT LIFT: The Patriot Lift has been designed to make transporting and using the lift as simple as possible. The design makes the lift 100% ADA compliant by providing two separate operating modes; one for transporting the lift and one for using it. DO NOT ATTEMPT TO USE THE LIFT WHILE IN THE TRANSPORT MODE! MODES OF OPERATION: 1] TRANSPORT MODE: In this mode the lift is on top of the portable cart and the brake-foot is raised, allowing the lift to roll and turn freely.
RETURNING THE LIFT TO TRANSPORT MODE: To move the lift after use, reverse the steps above as follows: 1) Tilt the lift back and down until it is almost horizontal to the deck. 2) Slide the lift back and up along the slide-slots until it stops at the top-end of the slots. 3) Pivot the lift forward and down until it is resting on the cart. Rotate the brake-foot handle counter-clockwise and raise it off the deck. The lift is now ready to move.
24V BATTERY SYSTEM OPERATING AND INSTALLATION INSTRUCTIONS WALL MOUNT CHARGER 24V SEALED BATTERY CONTROL BOX & HANDSET REMOTE The Pro Pool Lift TM Battery system comes with a 24v sealed rechargeable battery, wall mount charging unit (with mounting bracket), control box, and a waterproof handheld controller. The control box is mounted to the Pro Pool Lift TM and has a plug-in socket for both the actuator and the handheld controller.
BATTERY MAINTENANCE 1. RECHARGE THE BATTERY AS OFTEN AS POSSIBLE. The battery power unit is a sealed lead acid battery pack. Frequent recharges will prolong the battery life and maintain a high cold amperage capacity. 2. Do NOT expose the battery to freezing temperatures. 3. Do NOT expose the battery to prolonged periods of extreme heat or severe cold temperatures. 4. Do NOT expose the battery to long periods of direct sunlight. Heat will shorten your battery life.
PRO POOL LIFT OPERATING INSTRUCTIONS: NOTE: CHECK ALL NUTS & BOLTS FOR TIGHTNESS AND FOR WORN PARTS BEFORE EACH USE. NEVER OPERATE THE LIFT WITH THE ARMRESTS FLIPPED UP. The Pro Pool Lift TM should always be in the full up or deck position before a user attempts to transfer into the chair. Before attempting to transfer into the chair, check to make sure the lift is operating by making a short test run: move the chair at least part way in and out of the pool.
PRO POOL LIFTTM –HEADREST (OPTIONAL) ITEM # QTY. DESCRIPTION 1 1 HEADREST PAD 2 1 HEADREST SUPPORT 3 2 1/ 8”x3/ 4"S. S.S CREW TOOLS NEEDED: 5/ 64”DRI LLBI T PHILLIPS SCREWDRIVER ASSEMBLY INSTRUCTIONS 1. Begin by locating all parts in the above parts list. 2. Attach the headrest pad to the support bar by slipping the cross bar into the sewn supports on the back of the headrest pad. 3. Adjust the height of the headrest for the user and mark the hole locations (FIGURE 8). 4.
CARE OF YOUR LIFT Aqua Creek Pool Lift should not be stored in a pump room or in a storage room where pool chemicals are kept. Storing the lift near pool chemicals may cause rusting and other damage to occur. Your Aqua Creek stainless steel lift is powder coated to protect the stainless steel from rusting. Most rusting will occur at weld points, crevices, under gaskets, rivets or bolt heads. The choice of a proper cleaning product is up to the consumer and there are many to choose from.
TROUBLESHOOTING GUIDE Before troubleshooting make sure the battery is fully charged. I ft hel i f tdoe s n’ tmovewhe nt heha nds e tbut t o ni spr e s s e d: Whe ny ouc a n’ tg e tt hel i f tt o move check the following things: 1. Make sure the battery is fully charged: A. Before charging the battery first make sure the green light on the front of the charger is illuminated (this means that the charger is on).
If the battery is fully charged and the lift is not moving then: 2. Check all cords: A. Check that the cords are properly plugged in. Start by unplugging the remote and the actuator cord from the control box. Once these cords are removed check the ends for corrosion or damage. Plug the remote cord back in by lining up the raised tab on the plug to the grooved line on the control box outlet. Note that these cords require some force to plug them in fully.
If the lift stops moving over the water and is stuck: 4. Then try pushing the emergency button: A. If the lift gets stuck out over the water use a pen or pencil tip and stick it into the emergency button on the front of the control box to retract the lift. Note the lift will not retract if the battery is not fully charged or if the control box is not working. The emergency button only overrides the remote in case it has gone bad.
PRO POOL LIFT: PARTS LIST ITEM # QTY 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 4 1 1 1 2 2 2 2 2 2 1 2 4 3 3 2 1 1 2 DESCRIPTION PRO POOL BASE PRO POOL FRAME PRO POOL ACTUATOR FRAME PRO POOL SEAT ROTATE ARM PRO POOL SEAT ARM PRO POOL CONTROL ARM CHAIR ASSEMBLY FOLDING FOOTREST TUBE FOLDING FOOTREST LINEAR ACTUATOR 24 VDC LEAD-ACID BATTERY CONTROL BOX HANDSET CONTROL BATTERY/CB BRACKET 1/4"-20 x 1/2" HEX BOLT, S.S.
SEAT ASSEMBLY: PARTS LIST ITEM # QTY DESCRIPTION 1 1 SEAT BODY 2 2 SEAT ARMREST TUBE 3 2 SEAT ARMREST HANDGRIP 4 2 1/4"-20 x 3" HEX BOLT, S.S. 5 2 1/4" FLAT WASHER, S.S. 6 1 1/4" QUICK RELEASE PIN, S.S. 7 1 LANYARD FOR QRP 8 1 SHEET METAL SCREW, S.S.
PATRIOT PORTABLE: PARTS LIST ITEM NO.
Aqua Creek Products, LLC Limited Warranty: Pr o Pool L ift™ - 24v Battery Powered Patriot Portable LiftTM Aqua Creek Products lifts have a Limited Lifetime Warranty on the frames, not including the powder coat finish. Aqua Creek Products, LLC (a.k.a.