User Manual

ManualsBrandsActiveforever ManualsSports and recreationMettler Sys*Stim 294 4-Channel Neuromuscular Stimulator

Sys

Stim 294 Specifications

General Specifications:

Input: 90–240 VAC, 50–60 Hz, 2.3 Amp. Nom.

ETL and C-ETL Listed:

Domestic Model

Model ME 294 (9801427)

Classification: Protective Class I Equipment

CE model

Type BF Equipment

Enclosed equipment without protection against ingress of

water.

Equipment not suitable for use in the presence of a

flammable anesthetic mixture with air or with nitrogen oxide

Year 2000 Compliant Yes

Weight: 9.4 pounds

4,3 kg

Dimensions: 5 in (H) x 14.5 in (W) x 10 in (D)

12,7 cm (H) x 36,8 cm (W) x 25,4 cm (D)

Operating Temperature: +50°F to +104°F

+10°C to +40°C

Humidity:

Operating, 30% to 75% Relative Humidity at 104°F (40°C)

Nonoperating, 5 to 95% Relative Humidity, non-condensing

Storage Temperature: -40°F to 167°F

-40°C to 75°C

Storage Humidity: Storage, 30% to 90% Relative Humidity at 40º C, Non-

condensing

Storage Pressure: 700-900 mB

Environmental Disposal: The device contains lead in the form of solder used to

produce electrical contact between components. To avoid

adverse environmental impact, utilize a disposal facility that

performs complete incineration of the device at a temperature

in excess of 1000°C.

The shipping materials are fabricated of cardboard and may

be disposed of with other paper products.

Treatment timer:

Timer Accuracy: ±0.5 minutes for times less than 5 minutes

±10% for times from 5 to 10 minutes

±1.0 minute for times greater that 10 minutes

±5%, CE specification

Maximum Treatment Time: 60 minutes–electrical stimulation

Summary of content (5 pages)

PAGE 1
Sys*Stim 294 Specifications General Specifications: Input: 90–240 VAC, 50–60 Hz, 2.3 Amp. Nom. ETL and C-ETL Listed: Domestic Model Model ME 294 (9801427) Classification: CE model Protective Class I Equipment Type BF Equipment Enclosed equipment without protection against ingress of water. Equipment not suitable for use in the presence of a flammable anesthetic mixture with air or with nitrogen oxide Year 2000 Compliant Yes Weight: 9.4 pounds 4,3 kg Dimensions: 5 in (H) x 14.
PAGE 2
Treatment Timer: Treatment time counts down to zero when a time is set, or up to 60 or 30 minutes when no time is set. The digital timer indicates time in minutes and seconds. The timer also indicates the remaining or elapsed treatment time during the “Hold” period. Waveform Specifications: Interferential Mode Waveform Type: Polarity: Volts: Current: Figure 3.8— Interferential Waveform Average current at maximum intensity and frequency: Maximum current density under 2" diameter electrode.
PAGE 3
Frequency: Frequency Modulation: 4,000 Hz 1–15 Hz 80–150 Hz 1–150 Hz xx–xx Hz, xx=any value from 1 to 250 Hz Phase Duration: 125 µs internal sine wave 4–1,000 ms beat envelope Available Amplitude Modulation Options: Continuous Surge Reciprocation Available Channels: All Waveform Type: Polarity: Volts: Current: Average current at maximum intensity and frequency: Maximum current density under 2" diameter electrode.
PAGE 4
Biphasic (TNS) Mode Waveform Type: Polarity: Volts: Current: Figure 3.11—Biphasic (TNS) Waveform Average current at maximum intensity and frequency: Maximum current density under 2" diameter electrode. Frequency: Frequency Modulation: Phase Duration: Available Amplitude Modulation Options: Symmetrical biphasic square wave None 99 volts peak, 1 Kohm load 0 –99 mA peak, 1 Kohm load 7.2 mA 0.
PAGE 5
Microcurrent Mode Waveform Type: + - Polarity: or + - Figure 3.13—Microcurrent Waveform Volts: Current: Average current at maximum intensity and frequency: Maximum current density under 2" diameter electrode. Frequency: Duty Cycle: Frequency Modulation: Pulse Duration: Available Amplitude Modulation Options: Available Channels: Monophasic or biphasic square wave Positive or negative or biphasic pulses 1 Volt peak, 1 Kohm load 10-990 µA peak, 1 Kohm load 990 µA 24.4 µA/cm² 0.