KA1000 Dual Alarm Clock with Wireless Alarm Monitoring Receiver INSTRUCTION MANUAL 1st Edition
CONTENTS Important Safety Instructions.........................................................................................3 CONSUMER INFORMATION ..................................................................................4 INTRODUCTION .......................................................................................................6 KA1000 ALARM CLOCK ..........................................................................................7 INSTALLATION ...................................
IMPORTANT SAFETY INSTRUCTION When using your KA1000, you should always follow these basic safety precautions to reduce the risk of fire, electric shock, and injury to person, including the following: 1. 2. 3. 4. 5. 6. 7. 8. 9. 10. 11. 12. 13. 14. 15. 16. Read and understand all instructions before installing the KA1000. Unplug the unit from the adaptor and the telephone cord before installing a back-up battery. Do not dispose the batteries in a fire; follow your local code for properly disposing batteries.
Notice: the Canadian Department of communications label identifies certified equipment. This certification means that the equipment meets certain telecommunications network protective operational and safety requirements. The Department does not guarantee that the equipment will operate to the user’s satisfaction. Before installing this equipment, the users should ensure that it is permissible to be connected to the facilities of the local telecommunications company.
d) The REN is used to determine the number of devices that may be connected to a telephone line. Excessive RENs on a telephone line may result in the devices not ringing in response to an incoming call. In most but not all areas, the sum of RENs should not exceed five (5.0). To be certain of the number of devices that may be connected to a line, as determined by the total RENs, contact the local telephone company.
INTRODUCTION Thank you for your purchase of dual alarm clock KA1000- the best design in alarm and monitoring systems but easy and simple to set up and use. The alarm clock will trigger either the bed shaker, table lamp, or sound to absolutely wake you up every morning. You could select a combination of sound and light or shaker and light to fit your lifestyle. It is created with other features as well to help protect life and organize your house better.
KA1000 DUAL ALARM CLOCK Night lamp 1 Time button Time Security timer button Snooze button Snooze SCT Hour Hour Alarm 1 button ALA1 Alarm 2 button Minutes Min.
INSTALLATION A. Dual Alarm Clock KA1000: The best location to set the alarm clock KA1000 is next by the table lamp and close by the telephone outlet in your bedroom. It also can be used in your living room or kitchen where a lamp is available and be seen at many angles. Many KA1000 can be installed at different locations as your desired.
REGISTER TRANSMITTERS TO THE CLOCK After installation, the KA1000 is ready to register its door knock, doorbell, telephone ringer, and other accessories in the system. The door knock, telephone ringer and baby room call will be installed in channel 2 (C2). Other monitoring transmitter will be installed in channel 1 (C1). The dip switch code of each transmitter will be stored in KA1000 channel memory indicated by: CX:OX -> MEMORY LOCATION Registering the door knock with the KA1000: 1.
Press test button on transmitter to register to the clock or KA300 alarm monitor. Repeat this process for each transmitter. FIG. 7.2 Time FIG. 7.1 Snooze SCT Hour ALA1 FIG. 7.3 Min. ALA2 AM PM ALA1 ALA2 SCT ALAR M Setup clock alarms and real time SCT SENS OR BATTERY KA1000 KA300 1. Press the Time and the Hour (or Minute) buttons simultaneously to change the time setting. 2. Press Ala1 or Ala2 button and hold to check the alarm setting. 3.
Mode selector: You can choose shaker or sound and combine it with light when the alarm is triggered. Choose shaker and light for a silent alarm. It will wake just you, and not the other. You may turn on all three sound, light and shaker for a certainly wake up. Reading lamp or night light: Built-in night light or reading lamp (if table lamp is installed) will be turned On/Off from the light switch. Using LED indicators Mode LEDs: The corresponding LED will be illuminated for set up mode.
ACCESSORIES The dual alarm clock system is designed to work in correspondence with other wireless receivers and work with all KA300 transmitters (sold separately). Select from the following to complete your system. A. Extended receiver: (KA1000EX) Turn on the lamp and plug into the extended receiver. Plug the extended receiver into an AC outlet and the light will flash to notify you everywhere it is placed: kitchen, living room, bathroom etc.
Note: * Turn on the table lamp from the light switch on the extended receiver. Leave the switch on the lamp in the ON position or it will not flash the light. * The alarm function of the alarm clock KA1000 will not trigger the extended receiver. * The extended receiver is on stand-alone unit and receives signals directly from a transmitter. It does not need a KA1000 clock to operate.
Note: * Do not block the smoke chamber on smoke detector. Install the transmitter on the siren side. * Test the system by pressing the test button on the fire alarm to make sure that the fire alarm and the transmitter work. Do not press test button on the transmitter to test the system. G. Weather Alert Transmitter (KWA300TX): Choose the event you want to alert on the weather radio (WR300).
TEST AND TROUBLESHOOTING Testing: Testing the KA1000 every night before you go to bed is recommended to guaranty it will wake you up in the morning. Slide the test switch to the “Test” position and watch for the system send out a signal to the shaker, speaker, and lamp. Check for any loose connections, or problems with the light bulb before contacting the manufacturer. Troubleshooting: If any question arises during the installation and testing, follow through the troubleshooting section below.
7. How to match the flash pattern for all extended receiver (KA1000EX): Write on a cheat sheet the order of transmitters you are going to register on the first extended receiver (page 19 of this manual). Apply the same order when registering the second extended receiver. There are 16 different patterns for 16 entries. 8. The clock responds to channel one with fire alarm detector but not for the CO detector:’ Register the transmitter on the CO detector with the clock.
SPECIFICATION Working Frequency . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .433Mhz Memories . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6 Channel one for alarm monitor transmitter . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 Channel two for KA1000 transmitter . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 SIZE KA1000 . . . . . . . . . . . . . . . . . .
