Instructions / Assembly

PREFACE
Thank you for purchasing the ActiveAir brand electrical magnetic air
compressor. For optimum performance and safety, please read this
manual carefully and keep it handy for future reference.
USES
ActiveAqua Air Compressors are perfect for running several reservoirs
or multiple air stones at once. Additionally, it can be used for inflating
air beds, cleaning, or any other task that needs the availability or
compressed air.
APPLICATION
Fig1. Water treatment Fig2. Air supply for aquarium Fig3. Printer
Fig4. Liquid transmission Fig5. Spare parts cleaning Fig6. Air bed
Fig7. Medical equipment Fig8. Manufacture
OPERATION
1. Connect the outlet hose to the distributor and start the unit. For using in
reservoirs, the outlet hose may be connected to tubing manifold
for air stones or air curtain. Each unit can supply air to 6-12 tubes. (Fig.1)
2. In the event that the outlet air is obstructed or blocked, check the connecting
parts for leakage. If none is found, disconnect the plug, remove the front cover,
the valve and the valve base and wash away the dust with water. When done,
carefully dry and remount. (Refer to the diagram).
3. If the unit does not work after connecting to the power source, in most cases
the connecting point of the diode is broken or an obvious shift has occured
between the gap of the motor’s piston and housing due to the rough
transportation. Re-assembly of all parts is needed for resuming normal
operation. (Fig.2)
4. When connecting air hoses, adjust the length of the air outlet on the
compressor and the air intake to ensure the hose is not kinked or blocked. (Fig.3)
5. When the work area is separated from the power source, use an extension cord
of sufficient thickness and capacity. Use the shortest possible extension cord to
meet your needs.
6. Regularly inspect all mounting screws to ensure that they are properly tightened.
Should any of the screws be loose, retighten them immediately.
SAFETY TIPS
1. Make sure that the power source conforms to the power requirements
specified on the product nameplate. Use a standard AC outlet.
2. This appliance should be grounded while in use to protect the operator from
electric shock.
3. Do not carry the machine by the power supply cord or place heavy items on
top of it. Do not use if the cable or plug is damaged.
4. In order to avoid the water flowing back, the machine must be put above the
water level or install a check valve on the outlet pipe.
5. Clean the filter sponge within two months in order to guarantee the air purty.
6. During operation, if the engine sound is interrupted, indicators no longer
illuminate, or anything abnormal occurs, immediately unplug the power cord
from the outlet and contact your retailer.
7. The unit is non-oil lubricating design, please don’t add any oil lubrication.
8. To clean, unplug the appliance, wipe the it with a soft cloth lightly dampened
with soapy water. Do not wipe the plastic parts with solvent.
9. Place the unit horizontally on its base and avoid bumping it into things.
10. Please keep the machine away from high temperature, sunshine, damp or dust.
11. Disconnect the power supply plug if the appliance will not be used for a
long time.
12. Never attempt to repair or reconstruct this unit. Let qualified technicians
check and repair your unit.
FEATURES
1. The case is made of high-quality ZL 102 aluminum alloy with radiator,
heat-dissipation is more effective.
2. Reciprocating, linear electromagnetic motor and piston assembly allows for
smaller packaging and more efficient compression and discharge.
3. Cylinder and piston constructed from new lower friction, high wear resistant
SF material, which reduces power consumption and extends life.
4. Self-lubricating design ensures compressed air is not contaminated by oil.
5. Constant temperature and pressure operation to ensure reliable performance.
PARTS LIST
1 Air Inlet Filter 2 Spring
3 Motor Coils 4 Cylinder
5 Rotor 6 Piston
7 Inlet & Outlet Valves
8 Air Outlet Adaptor
HOW IT WORKS
When the electromagnetic coils are energized by AC power, a magnetic force is
generated. Under the action of this magnetic force and the pressure spring, the
piston moves reciprocally so that the volume of cylinder changes.
This leads to the automatic opening and shutting of the inlet and outlet valves
and thus achieves the work cycle of taking in, compressing and discharging.
1 Air inlet filter 2 Rear ball base 3 Steel ball 4 Front ball base 5 Spring 6 Rear housing
7 Motor 8 Front housing 9 Sf piston 10 Valve base 11 Valve clack 12 Front cover
AAPA45L
AAPA70L
AAPA110L
Please read this manual prior
to operation and keep it
handy for future reference.
Distributed by Hydrofarm, Inc. | Petaluma, CA USA | Made in PRC
www.Hydrofarm.com