WEB7200 WiFi 6 Repeater Actiontec WEB7200 WiFi 6 Repeater User Manual Table of Contents Table of Contents 1 Introduction 3 Features 4 Getting to Know the Extender 5 Front Panel 5 Back Panel 6 Installing the Extender 7 Accessing the Extender’s GUI 9 Status 10 Wireless Setup 10 Advanced Setup 13 Specifications 15 Notices 17 Warranty 17 Important Safety Instructions 18 Basic safety precautions should always be followed to reduce the risk of fire, electrical shock, and personal injury, including the following:
WEB7200 WiFi 6 Repeater Introduction The Actiontec WEB7200 is a wireless network extender with dual concurrent radios supporting both 2.4GHz and 5GHz operation in 802.11ax. This allows the Extender to connect to everything from legacy wireless laptops, computers, and gaming platforms, up to the most current (and future) Apple and Android tablets, laptops, media platforms, and smartphones.
WEB7200 WiFi 6 Repeater Features • Fast 802.11ax Wi-Fi wherever you need it • Upgrade to 802.11ax speeds without replacing your router • Dual band concurrent radio for wireless throughput up to 2Gbps • 2x2 802.11ax 5 GHz radio • 2x2 802.11ax 2.4 GHz radio • Two Gigabit Ethernet ports • USB 2.0 port • WPA3, WPA2, WPA security with AES encryption • Wi-Fi Protected Setup (WPS) Getting to Know the Extender This chapter describes the location and uses of the Extender’s LEDs, ports, and buttons.
WEB7200 WiFi 6 Repeater • Flashing Green signifies Initial Bootup. • After bootup completion, solid Blue signifies no backhaul connection, the unit is waiting end user to push the WPS button to initiate the pairing with residential gateway. • After pushing the WPS button, if there is another Access Point trying to pair, the unit will flash Blue, signifying backhaul pairing process.
WEB7200 WiFi 6 Repeater Installing the Extender There are two parts to installing an Extender: syncing the Wi-Fi settings, and placing and connecting the Extender. Syncing Wi-Fi To sync the Extender with the gateway/modem's Wi-Fi settings: 1. Place the Extender next to the gateway/modem. 2. Plug the Extender's power adapter into the Power port of the Extender, and the other end into an electrical wall outlet. 3. Wait until the WPS button on the Extender is flashing purple. 4.
WEB7200 WiFi 6 Repeater 1. Ensure that the Extender is connected to an Actiontec gateway/modem, and that both devices are powered on. 2. On a computer connected to the same network as the gateway/modem and Extender, log in to the gateway/modem's GUI. Find the list of devices that are connected to your gateway/modem. 3. Find the Extender by its MAC ID from the list of connected devices or status screen.
WEB7200 WiFi 6 Repeater SSID Broadcast This option controls whether or not the name of the network is broadcast to other wireless devices (usually, in the device’s available wireless network list). Select Enable or Disable by clicking in the appropriate radio button. Transmit Power This option controls the power of the Extender’s wireless radio. We recommend leaving this setting at 100%. Wireless Band This option allows the user to select the bandwidth at which the Extender’s wireless radio will operate.
WEB7200 WiFi 6 Repeater configure various administrative aspects of the Extender and its GUI. They should be adjusted by an experienced network technicians only. Management The Management screen allows the Extender’s IP address settings to be modified. Only experienced network technicians should change these settings. Factory Default The Factory Default advanced setup screen allows the Extender's factory default settings to be reapplied, erasing all current settings.
WEB7200 WiFi 6 Repeater Power Adapter Input 90-240VAC@ 0.5A Output 12Vdc@ 2A Made by Actiontec, model # CDS024T-W120U Regulatory FCC 15B, 15C, ISE Canada ICES UL, K.21 Wi-Fi, WPS RoHS Environmental Operating temperature - 0°C to 40°C (32°F to 104°F) Storage temperature - 0°c to 70°C (32°F to 158°F) Operating humidity- 10% to 85% non-condensing Storage humidity - 5% to 95% non-condensing Altitude: -197 ft. to 7000 ft. Note: Specifications are subject to change without notice.
WEB7200 WiFi 6 Repeater • Do not block any ventilation openings. Install in accordance with the manufacturer's instructions. Do not install near any heat sources such as radiators, heat registers, stoves, or other apparatus including amplifiers that produce heat. • Do not use the telephone to report a gas leak in the vicinity of the leak. • Use only the power cord indicated in this manual if applicable.
WEB7200 WiFi 6 Repeater Important Note on Wi-Fi If applicable, this equipment complies with FCC/Industry Canada radiation exposure limits set forth for an uncontrolled environment. The radio has been found to be compliant to the requirements set forth in CPR 47 Sections 2.1091, 15.247 (b) (4),15.407 addressing RF Exposure from radio frequency devices as defined in Evaluating Compliance with FCC Guidelines for Human Exposure to Radio Frequency Electromagnetic Fields.
