Coaxial-to-Ethernet Conversion Kit Bonded MoCA Network Adapter Model # ECB6200 User Guide 0535-005-000 rev.
Table of Contents Table of Contents 1 Getting Started 3 Introduction 3 Package Contents 4 Requirements 4 Features 4 Connecting the Adapters 5 Connecting the First Adapter 5 Connecting Additional Adapters 7 Specifications 9 Notices 11 Warranty 11 Important Safety Instructions 12 1
Bonded MoCA Network Adapter FCC Class B Equipment 13 Technical Support 15 2
Getting Started Introduction Congratulations for purchasing the Actiontec ECB6200 Bonded MoCA Network Adapter. The Adapter is a simple, flexible solution for extending a home network. By leveraging the ubiquity of coaxial cabling within the modern home, the Adapter provides an Ethernet Internet port anywhere a coaxial connection is available. It also features a TV/STB Out coaxial port to allow for existing connections at the coaxial wall port.
Bonded MoCA Network Adapter Package Contents • ECB6200 Bonded MoCA Network Adapter • Coaxial cable • Power adapter • Quick Start Guide • Ethernet cable Requirements • Available coaxial port in installation areas • Available electrical wall socket in installation areas Features • Ethernet port (gigabit) • Coax In coaxial port (v. 2.0) • TV/STB Out coaxial port (v. 2.0) • Power, Coax, and Ethernet LEDs: - Power LED: glows solid green when Adapter is powered up.
Connecting the Adapters Connecting the Adapter is a relatively simple process. First, connect one Adapter to the TV or set-top box, the broadband modem or router, and the coaxial network to establish the Internet signal. Then, additional Adapters can be installed throughout the home or office at any location Ethernet Internet access is needed, and an available coaxial port is available.
Bonded MoCA Network Adapter 7. Plug the provided power adapter into the Power port on the side of the Adapter. 8. Plug the other end of the power adapter (external, 5V DC, 2A, made by APD, model #WA-10P05FU) into an electrical outlet. When complete, the setup should look similar to the figure below: ! The Internet signal is now being delivered across the coaxial network.
Connecting the Adapters Connecting Additional Adapters If necessary, additional Adapters can be placed at locations around the home or office that need an Ethernet Internet connection, but currently only have a coaxial port. To connect additional Adapters: 1. Find a coaxial wall port near the desired location and unplug the coaxial cable connected to the TV or set-top box. If no device is plugged into this coaxial wall port, skip to step 3. 2.
Bonded MoCA Network Adapter 8. Plug the other end of the power adapter (external, 5V DC, 2A, made by APD, model #WA-10P05FU) into an electrical outlet. When complete, the setup should look similar to the figure below: ! The device connected to the Ethernet port is now connected to the Internet via the coaxial network. Repeat this process to install additional Adapters throughout the home.
Specifications ! ! ! ! Model Number ECB6200 IP LAN MoCA (v. 2.0; up to 1.4 Gbps throughput) LAN Ethernet Port 10/100/1000 (1) LAN Connections Coax In Frequency Range - Extended D-band: 1125MHz ~ 1675MHz; Full Port Range: 5MHz ~ 2150MHz TV/STB Out Frequency Range - 5MHz ~ 1002MHz LED Indicators Power, Coax Power External, 5V DC, 2A, 1.
Bonded MoCA Network Adapter Environmental Ambient temperature - 0ºC to 40ºC (32ºF to 104ºF) Storage temperature - -20ºC to 85ºC (-4ºF to 185ºF) Operating humidity - 10% to 85% non-condensing Storage humidity - 5% to 90% non-condensing Note: Specifications are subject to change without notice.
Notices Warranty This product has a one-year Limited Hardware Warranty and 90-day free software updates from date of purchase. Local Law This Limited Warranty Statement gives the customer specific legal rights. The customer may also have other rights which vary from state to state in the United States, from province to province in Canada, and from country to country elsewhere in the world.
Bonded MoCA Network Adapter Important Safety Instructions Basic safety precautions should always be followed to reduce the risk of fire, electrical shock, and personal injury, including the following: • Do not use this product near water – for example, near a bathtub, kitchen sink, laundry tub, or swimming pool, or in a wet basement; only clean with dry cloth. • Do not block any ventilation openings. Install in accordance with the manufacturer's instructions.
Notices FCC Class B Equipment This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications.
Bonded MoCA Network Adapter Modifications The FCC requires the user to be notified that any changes or modifications made to this device that are not expressly approved by Actiontec Electronics, Inc, may void the user’s authority to operate the equipment. Declaration of Conformity for Products Marked with the Industry Canada (IC)–Canada only This device complies with Industry Canada license-exempt RSS standard(s). Operation is subject to the following two conditions: 1.
Notices Technical Support Go to www.actiontec.
