Notebook Computer User's Guide
Preface Copyright 2003 All Rights Reserved. Manual edition, March 2003 The information in this document is subject to change without prior notice in order to improve reliability, design and function and does not represent a commitment on the part of the manufacturer. In no event will the manufacturer be liable for direct, indirect, special, incidental, or consequential damages arising out of the use or inability to use the product or documentation, even if advised of the possibility of such damages.
manual, the manufacturer and distributor assume no liability resulting from errors or omissions in this manual, or from the use of the information contained herein. Notices Federal Communications Commission Radio Frequency Interference Statement N NO OTTE E:: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules.
for compliance could void the user’s authority to operate the equipment. Shielded interface cables and a non-shielded AC power cord must be used in order to comply with emission limits. This equipment is to be used with power supply: I/P: 100-240 Vac, 50-60Hz, 1.8A O/P: 19Vdc, 3.42A There is no internal power supply. Canadian DOC Notice For Class B Computing Devices This Class B digital apparatus meets all requirements of the Canadian Interference - Causing Equipment Regulations.
. Lay this equipment on a reliable surface when isntall. A drop or fall could cause injury. 7. Make sure to use the right voltage for the power source when connecting the equipment to the power outlet. 8. Place the power cord in such a way that people can not setp on it. Do not place anything on top of the power cord. 9. All cautions and warnings on the equipment should be noted. 10.
15. The unit can be operated at an ambient temperature of max. 35°C. 16. The sound pressure level at the operators position according to IEC 704-1: 1982 is equal or less than 70 dB(A). 17. Power Cord Requirements The power cord set used with the AC adaptor must meet the requirements of the country where you use the AC adaptor, whether it is 100-120 or 200-240 Vac. The following information explains the requirements for power cord set selection.
always be followed to reduce the risk of fire, electric shock and injury to persons. These precautions includes the following: 1. 2. 3. 4. Do not use this product near water, for example, near a bathtub, washbowl, kitchen sink or laundry tub, in a wet basement or near a swimming pool. Avoid using a telephone (other than a cordless type) during an electrical storm. There may be a remote risk of electric shock from lightning. Do not use the telephone to report a gas leak in the vicinity of the leak.
4. Die Netzanschluβsteckdose soll nahe dem Gerät angebracht und leicht zugänglich sein. 5. Das Gerät ist vor Feuchtigkeit zu schützen. 6. Bei der Aufstellung des Gerätes ist auf sicheren Stand zu achten. Ein Kippen oder Fallen könnte Beschädigungen hervorrufen. 7. Beachten Sie beim Anschluß an das Stromnet die Anschlußwerte. 8. Verlegen Sie die Netzanschlußleitung so, daß niemand darüber fallen kann. Es sollte auch nichts auf der Leitun abgestellt werden. 9.
Wenn das Gerät nicht der Bedienungsanleitung entsprechend funktioniert oder Sie mit Hilfe dieser Anleitung keine Verbesserung erzielen. Das Gerät ist gefallen und/oder das Gehäuse ist beschädigt. Wenn das Gerät deutliche Anzeichen eines Defektes aufweist. d. e. f. 14. VORSICHT: Explosiongsgetahr bei unsachgemäßen Austausch der Batterie. Ersatz nur durch denselben oder einem vom Hersteller empfohlenem ähnlichen Typ. Entsorgung gebrauchter Batterien nach Angaben des Herstellers. 15.
• Alle Teile des Kabel-Sets müssen entsprechend dem japanischen Dentori Law mit einem “T”-Symbol markiert sein • Die Minimalanforderungen für das Kabel sind .75m ㎡ Leiter. C. Für andere Länder: • Die Zubehörteile des Kabel-Sets müssen das Prüfsiegel derjenigen Stelle, die in dem jeweiligen Land für die Sicherheitsprüfung zuständig ist, tragen. • • Das Kabel muss vom HAR (harmonisierten) Typ H05VV-F sein.
Laserstrahl, vermeiden Sie Kontakt mit dem Strahl bei offenem Gehäuse. 21. Es besteht Explosionsgefahr, wenn der Akku nicht ordnungsgemäß ersetzt wird. Ersetzen Sie den Akku nur durch einen Akku gleichen oder äquivalenten Typs, der vom Hersteller empfohlen wird. Entsorgen Sie Akkus entsprechend den Anweisungen des Herstellers. Entfernen Sie den Akku auf keinen Fall bei eingeschaltetem Notebook, da hierdurch Daten verloren gehen könnten.
Optional Equipment: xi
Chapter 1 Introduction 1
W WA AR RN NIIN NG G:: TThheerree aarree m moorree aanndd m moorree ppeeooppllee ssppeennddiinngg llaarrggee aam moouunnttss ooff ttiim e i n f r o n t o f c o m p u t e r m o n i t o r s n o w t h a t s c i e n t room me in front of computer monitors now that scientiissttss ffr m m maannyy ffiieellddss iinncclluuddiinngg aannaattoom myy,, ppssyycchhoollooggyy,, aanndd ooccccuuppaattiioonnaall ssaaffeettyy aarree iinnvvoollvveedd iinn tthhee ssttuuddyy ooff eerrggoonnoom miiccaallllyy ssoouunndd w woorrkk
Getting to Know Your Computer Opening the LCD Panel At the front of the Notebook you will find a retaining latch on the display panel that locks the display in closed position when the Notebook is not in use. 1. Slide the display panel latch to the right until the display panel releases, and then raise the LCD screen. 2. At any time you can tilt the display toward or away from you to a comfortable viewing position. C CA AU UTTIIO ON N:: To avoid damage to the display panel: 1.
Each of these features is briefly described below. 1. LCD Cover Release Latch Slide this latch to the right to open the LCD cover.
2. LCD Screen Your Notebook computer is equipped with a replaceable color Liquid Crystal Display (LCD) screen that supports up to 1024 x 768 or 1400 x 1050 x 16M LCD resolution utilizing a AGP BUS. A built-in backlight allows you to comfortably view the screen even when ambient lighting is low. 3. Internet Explorer Button Use this key to open the Internet Explorer. 4. Outlook Express Button Use this key to open Microsoft's Outlook to send/receive your mail. 5.
6. Power/Resume Button Pressing this button for 1-2 seconds will turn on the system or pressing this button when the computer is in Suspend mode will resume normal operation. Pressing this button for 4-6 seconds will also turn off the system. 7. TouchPad The TouchPad is hardware-compatible with the IBM PS/2 mouse and software-compatible with the Microsoft mouse. 8. TouchPad Buttons The buttons below the TouchPad correspond to the left and right buttons on a standard mouse.
The Left Side 1. Ventilation Opening Please don’t block this opening during operation of the system. 2. 1394A A very fast external bus standard that supports data transfer rates of up to 400 Mbps (400 million bits per second). Can be used to connect up 63 external devices, also supports isochronous data -- delivering data at a guaranteed rate. This makes it ideal for devices that need to transfer high levels of data in real-time, such as video devices.
4. PCMCIA Socket Button The computer has one PCMCIA type II socket 5. The LAN Port This jack provides a standard RJ-45 connection for integration with an existing network or a high-speed (DSL or cable) connection via a network cable. N NO OTTE E:: When using a LAN, please use an EMI Shielding Cable to minimize an inteference when transmitting. 6. The Modem Port This jack is an internal 56K voice/fax/data modem. You will connect your computer to your phone line through this port.
LED Indicators These three LED indicators are separately program for the following functions: Power On, Suspend Mode and Battery Charge. 1. Power On This indicator will lit when the notebook is powered On. 2. Battery Charge This indicator will lit green when the battery is in charging status. When the indicator light turns off, it indicates the system is in full charge. 3. Suspend Mode This indicator will lit when the notebook enter the suspend mode.
The Right Side 1. The CD-ROM/DVD-ROM or DVD CD-RW Combo (Option) Your Notebook comes with a swappable 24X (or higher) 5.25" IDE CDROM or 8X DVD-ROM. 2. DC IN Connector Plug the AC adapter into this connector.
1. Ventilation Opening Please don't block this opening during operation of the system. 2. Kensington Lock Allows you to connect a special computer lock to secure your system. You can purchase a lock at most computer retailers. 3. S-Video Port Allows you to connect any S-Video ready television to your system. You can display output simultaneously on both the LCD and the television or toggle between the two screens. 4.
It will eventually replace the need for separate connectors for external keyboards, serial ports, and parallel (printer) port.
1. Battery Your notebook comes equipped with a factory-installed battery pack module. After the battery runs down, the module can be removed and replaced with a charged battery. 2. Hard Disk Drive Your computer includes a 2.5-inch IDE hard disk drive (9.5mm in height). The notebook PC's BIOS automatically detects IDE drive types. 3. Battery Release Latch Lift up this latch to release the battery from its bay. 4.
Chapter 2 Getting Started
Connecting to a Power Source Connecting the AC Adapter A universal AC adapter is provided to supply your computer with power and also charge the computer’s battery pack. The adapter’s AC input voltage can range anywhere from 100 to 240 volts, covering the standard voltages available in almost every country. The power cord for the AC adapter requires a threehole grounded AC outlet. To connect the computer to an external power source: 16 1.
C CA AU UTTIIO ON N:: The best kind of AC power source to connect your Notebook to is a UPS (Uninterruptible Power Supply). Lacking this, use a power strip with a built-in surge protector. Do not use inferior extension cords as this may result in damage to your Notebook. The Notebook comes with its own AC adapter. Do not use a different adapter to power the computer and other electrical devices.
Operating on Battery Power Your computer comes with a rechargeable battery pack that lets you operate the computer without an external power source. When the battery pack is fully charged, you can operate the computer for approximately 2 hours under the following conditions: • The battery pack initially has a full charge. • No peripheral devices are installed. • The disk/CD-ROM drives run no more than 10% of the time. N NO OTTE E:: Only use batteries that are approved by an authorized dealer.
3. Gently lower the battery into the bay and push it until it clicks securely in the bay. To remove the battery pack: 1. Turn off the notebook, and disconnect the AC adapter. Close the LCD panel and turn it over and place it on a solid, flat surface. 2. Lift the release latch to release the battery from the bay. At this time the battery will now be angled slightly out of the bay.
3. 20 Hold the battery at the finger grip and lift it out of the compartment.
Charging the Battery Pack The installed battery pack charges automatically any time the computer is connected to the AC adapter and an external power source. It is a good idea to occasionally discharge the battery pack fully to preserve its operating performance.
Chapter 3 Using the Notebook Computer
Adjusting the LCD Screen Display The LCD screen display can be adjusted by the following key combinations. KEYS FUNCTIONS [Fn] + [F7] Decreases the brightness level. [Fn] + [F8] Increases the brightness level. [Fn] + [F10] Use this key combination to expand your video screen or reset to its original size. [Fn] + [F12] This key combination toggles the display between the LCD, CRT, simultaneous LCD/CRT, TV, simultaneous CRT/TV. LCD Care LCD screens are delicate devices that need careful handling.
• Simultaneous display of the LCD screen and CRT monitor • TV only • Simultaneous display of the TV screen and CRT monitor You can switch between these display configurations by pressing the key combination [Fn] + [F12]. For information on connecting an external display, please refer to Chapter Four. A Tour of the Notebook’s Keyboard The Notebook’s keyboard uses a standard QWERTY layout with the addition of special function keys and an embedded numeric keypad for number intensive data entry.
either the Notebook or external keyboard will enable/disable NumLock of both keyboards in unison. To disable the Notebook numeric keypad while keeping the keypad on an external keyboard activated, use the [Fn] + [NumLk] hot key on the Notebook keyboard. The Notebook’s Hot Key Controls KEYS FUNCTION(S) Power Button Press this button once to power on or enter the suspend/resume mode. Press this button for more than 4 seconds to power off the system.
to move the cursor. You can use the buttons below the touchpad as left and right mouse buttons. TouchPad Precautions The TouchPad is a pressure sensitive device. following precautions. 26 Please take note of the • Make sure the TouchPad does not come into contact with dirt, liquids or grease. • Do not touch the TouchPad if your fingers are dirty. • Do not rest heavy objects on the TouchPad or the TouchPad buttons.
You can use the TouchPad with Microsoft Windows as well as nonWindows applications. Connecting an External Tracking Devices The system will only enables you to use one tracking device whether it is an internal or external tracking device. Data Storage and Retrieval Data storage and retrieval are two of the most fundamental tasks you will perform when working with your computer. The Notebook is equipped with a hard disk drive (HDD). The HDD is removable allowing for easy upgrades.
• Use a clean, dry, cloth to remove dust, smudges, or fingerprints. Wipe from the center outward. • Do not write or place objects on the surface of the disc. • Store discs in a cool dry place not to damage the disc. • Do not use benzene, thinners, or cleaners with detergent. Only use CD-ROM/DVD-ROM cleaning kits. • Do not bend or drop the discs. Loading a Disc To play a CD disc, follow the instructions listed below. 1. Push the CD-ROM/DVD-ROM/Combo eject button on the CD drive door.
N NO OTTE E:: Do not insert any foreign objects into the disc tray. If you experience difficulty when ejecting the CD disk tray, stretch a paper clip (or use a pin or a thin metal rod) and insert it into the emergency eject hole located on the right side of the front panel. The CD disk tray should eject immediately. This procedure can also be used to remove a CD from the drive when the Notebook is powered off.
N NO OTTE E:: When inserting a Type II PC card, make sure the connector is inserted in the socket. Before ejecting a PC card, ensure that it is not being accessed by the System. For example, if the message “Write protect error writing Drive x” is displayed, the user has to change the write protect switch setting on the memory card. To change the switch setting, (a) eject the card, (b) change the switch setting, and (c) re-insert the card.
See Battery Status later in this section for a description and explanation of the Windows Battery icon. Charging the battery takes about 3 hours to charge when the system is in off state. If possible, always charge the battery completely. Removing the Battery Pack To remove the battery pack from its compartment, please refer to Chapter Two, Inserting and Removing the Battery Pack.
In general, using the battery until the low-low battery-warning indicator appears and fully recharges the battery each time (full discharge/charge cycle) will ensure the accurate reporting of the battery gauge status. Automatic Battery Pack Charging Function You can automatically charge the battery pack by using the AC Adapter. The charge time is about three hours when the Notebook power is turned off.
Your battery now has 1 ~ 2 minutes of battery charge remaining. You must save your data or connect AC power immediately; otherwise, you may lose your data. Sound Meaning Continuous beeping every 1.5 seconds Battery Low: Indicates that there is 7 to 10 minutes charge remaining. Beeping accelerates Battery Low Low: Indicates that there is 1 to 2 minutes of battery charge remaining. Save your work and turn off the Notebook, or connect the AC adapter.
Resetting the System After installing a software application package, you may be prompted to reset the system to load the changed operating environment. To reset the system, or “reboot,” press the [Ctrl] + [Alt] + [Delete] keys simultaneously. This is known as “warm boot.” This key combination acts as “software” reset switch when you encounter hardware or software problems, which lock up the Notebook.
Chapter 4 Desktop Operation
Your notebook is capable of providing you with efficient and productive mobile computing, it also has the speed and capacity to service as a desktop system. This chapter discusses those functions of your notebook that are typical of desktop systems. Audio The Multimedia Sound System The Notebook’s built-in audio capabilities allow you to take advantage of a wide range of education and entertainment multimedia software.
Audio Volume Control The Notebook is equipped with hot-key volume controls: Pressing the [Fn] + [F3] hot-key combination decreases the audio output volume, press the [Fn] + [F4] hot-key combination increases the audio output volume. Audio Software Your notebook comes equipped with an integrated sound system capable of providing you with quality audio sound through the built-in speakers or through external speakers connected via the system ports.
External Speakers and Microphone The sound system is capable in providing high-quality sound to external speakers and receiving and processing sounds from an external microphone or external sound source. Connecting Peripheral Devices To expand your computing capabilities, you can add a variety of external devices to your computer. You may, for example, want to add a mouse, modem, or a printer.
39
Chapter 5 Running BIOS Setup
Introduction The BIOS (Basic Input and Output System) Setup program is a menu driven utility that enables you to make changes to the system configuration and tailor your system to reflect installed hardware or alter system performance. When the Notebook is turned back on, the system is configured with the values stored in CMOS.
for the item that you are currently editing. The Menu Bar The top of the screen has a menu bar with the following selections: Main - Use this menu to make changes to the basic system configuration. Advanced - Use this menu to enable and make changes to the advanced features available on your system, such as enabling the FIR module. Security - Use this menu to set a password. The password allows bootup and controls access to the BIOS setup menu.
The following table lists the keys found in the legend bar with their corresponding alternates and functions. Legend Key Alternate Key Function F1 Alt + H Displays the General Help window. It can be enabled from anywhere in the BIOS. Esc Alt + X Jumps to the Exit menu or returns to the Main menu from a submenu. ← Selects the menu item to the left. → Selects the menu item to the right. ↑ or ↓ Keypad arrow keys Moves the cursor up and down between fields.
Launching Submenus Note that a right pointer symbol X appears to the left of certain fields. This pointer indicates that a submenu can be launched from this field. A submenu contains additional options for a field parameter. To call up a submenu, simply move the cursor to highlight the field and press the [Enter] key. Use the [Esc] key to return to the Main menu.
System Time Sets your system to the time that you specify. The format is hour, minute, second. Use the [Tab] or [Shift] + [Tab] keys to move between the hour, minute, and second fields. System Date Sets your system to the date that you specify (usually the current date). The format is month, day, year. Use the [Tab] or [Shift] + [Tab] keys to move between the month, day, and year fields.
This field is used to configure the IDE Hard Disk installed in the system.
N NO OTTE E:: Before attempting to configure a hard disk drive, make sure you have the configuration information supplied by the manufacturer of your hard drive. Incorrect settings can result in your system not recognizing the installed hard disk.
The Advanced Menu Selecting Advanced from the menu bar displays the Advanced menu: SuperIO Configuration Use this setting to configure your SuperIO Chipset. Quick Boot Allows BIOS to skip certain test while booting.
The configurations are: Disabled or Enabled (default value) Quiet Boot Disabled: Displays normal POST messages. Enabled: Displays OEM Logo instead of POST messages. The configurations are: Disabled (default value) or Enabled PS/2 Mouse Support Use this setting to select support for PS/2 mouse. The configurations are: Disabled or Enabled (default value) Legacy USB Support Enables support for legacy USB. Auto legacy support if no USB devices are connected.
The Security Menu The Notebook’s advanced system of security allows you to set a password to prevent unauthorized access to system resources, data, and the BIOS Setup Program.
The Boot Menu The Boot menu allows the user to specify the order in which the Notebook is to check for a device to boot the system. You can also configure the way that the system will boot up. To make changes, select Boot from the menu bar.
The Exit Menu Once you have made all of your selections from the various menus in the Setup program, you should save your changes and exit Setup.
Chapter 6 The Software Utilities Disks
AutoRun Installation Follow the step-by-step procedures on the CD-ROM/DVD-ROM to execute the “AutoRun” application by selecting the topic of “Driver Installation”. N NO OTTE E:: If you encounter this message when executing the Auto Run in Windows 2000, please perform the following procedures: Click on the “Start” – “Setting” – “Control Panel” – “System” – “Advanced” tab – “Performance” tab – “Change” tab – reduce the maximum Virtual Memory setting to 200MB.
6. Restart the system. Installing VGA Display Drivers for Win2K/XP This section describes the operation and installation of VGA display software drivers supplied on the Driver Utility CD-ROM that is shipped with your computer. 1. Insert the CD-ROM Driver into your CD-ROM/DVD-ROM drive. 2. Click “Start” and Select “Run”. 3. Type the following: D:\Driver\VGA\Setup.exe (If D is not your CDROM/DVD-ROM drive, substitute D with the correct drive letter). 4.
5. Follow the Wizard’s on-screen instructions to complete the installation. 6. Restart the system. Intalling the IR Driver for Win2K/XP To install the audio driver you must first remove the currently installed driver. 1. Insert the CD-ROM Driver into your CD-ROM/DVD-ROM drive. 2. Click “Start” and Select “Run”. 3. Type the following: D:\Driver\IR\Setup.exe (If D is not your CD-ROM/DVDROM drive, substitute D with the correct drive letter). 4. Click on “Setup” to begin the Installation Wizard. 5.
5. Follow the Wizard’s on-screen instructions to complete the installation. 6. Restart the system. Installing the TouchPad Driver for Win2K/XP To install the touchpad driver you must first remove the currently installed driver. 1. Insert the CD-ROM Driver into your CD-ROM/DVD-ROM drive. 2. Click “Start” and Select “Run”. 3. Type the following: D:\Driver\Touchpad\Win2K&XP\Setup.exe (If D is not your CD-ROM/DVDROM drive, substitute D with the correct drive letter). 4.
4. Click on “Setup” to begin the Installation Wizard. 5. Follow the Wizard’s on-screen instructions to complete the installation. 6. Restart the system. Installing the MiniPCI Combo Card Driver for Win2K/XP Please follow these instructions to install the Modem driver: 1. Insert the CD-ROM Driver into your CD-ROM/DVD-ROM drive. 2. Click “Start” and Select “Run”. 3. Type the following: D:\Driver\MiniPCI\Actiontec\Modem\Win2KXP\Setup.
4. Double click on the "Other Devices" , double click the " Network Controller " and click on the "Driver" tab. 5. Click the "Update Driver" tab and select the "Install from a list or specific location (Advanced)" item and click "Next". 6. Select the "Include this location in the search" item and click on the "Browse" button and specify for the designate location of your CD driver D:\Driver\MiniPCI\Actiontec\LAN\WinXP or D:\Driver\MiniPCI\Actiontec\LAN\Win2K to proceed with the installation.
You will notice three new entries have been made in the Display Properties window: ATI Displays, ATI color, ATI OpenGL, ATI Direct 3D, ATI Overlay and ATI Options. ATI Display With ATI Display, you can connect up to three displays simultaneously to the notebook. You can watch a DVD movie on an external television while checking email on your notebook screen - or surf the web on a CRT monitor while working on a presentation on a digital flat panel. The option is yours with these features.
61
ATI Color You can adjust the right resolution for your screen display.
ATI OpenGL Play the latest and greatest OpenGL based games as well as CAD/Design programs.
ATI Direct 3D An API for manipulating and displaying 3-dimensional objects.
ATI Options Display all the items concerning the ATI related function.
ATI Overlay 66
Chapter 7 Troubleshooting
This chapter describes locating and solving problems that you may encounter while using your computer. Locating a Problem Problems with your computer can be caused by something as minor as an unplugged power cord – or as major as a damaged hard disk. The information in this chapter is designed to help you find and solve minor problems. If you try all the suggested solutions and you still have a problem, make a list of what steps you have taken to correct the problem and contact your dealer.
Checking Cables and Connections Start by performing a careful visual inspection of the exterior of the computer. If no LEDs are illuminated, make sure that your computer and its peripherals are getting power and communicating with each other properly. To check the power cables, and connections: 1. If you have been using battery power, connect the Notebook to an external power source and make sure that the battery has a charge. 2.
N NO OTTE E:: Do not substitute cables for different devices (other than the manufacturer recommended cables) even if they look exactly alike. The wiring inside the cable may be different. 4. When you are certain that you have power available and all connections are good, turn the computer on again. If the computer still does not start, you may have a hardware problem. The Power-On Self Test The Power-On Self Test (POST) runs every time you turn on or reset the Notebook.
In general, if the POST detects a system board failure (a critical error), the computer halts and generates a series of beeps. If failure is detected in an area other than the system board (such as the display, keyboard, or an adapter card) an error message is displayed on the screen and testing is stopped. It is important to remember that the POST does not test all areas of the computer, only those that allow it to be operational enough to run diagnostic programs.
72 Problem: The message: “Invalid system disk, Replace the disk, and then press any key” appears during boot. Solution: Check and make sure that you do not have a non-bootable floppy diskette inserted in your floppy drive. If your USB FDD is empty, you may not have an operating system installed on your drive. Contact technical support for assistance. Problem: You hear irregular beeps during operation of the Notebook and the system halts. Solution: The problem is beyond the scope of this manual.
Solution: Ensure that the disk has been formatted. Consult your operating system manual for information on formatting floppy diskettes. Problem: The diskette is write-protected. Solution: Eject the diskette, remove the write protection, and try again. Problem: T h e d i s k e tte i f fu l l . Solution: Try using another diskette or free up some space on the diskette. The disk drive is not operating. Contact your dealer for support. Problem: You cannot use the mouse.
• 74 What have you done already to try to solve the problem? If you have overlooked a step, your dealer may be able to solve the problem over the phone.
Chapter 8 Upgrading your System
Upgrading your Memory Refer to the following instructions and illustration for information on upgrading your notebook's memory. 76 1. Turn off the computer and disconnect the AC adapter and all peripherals. 2. Turn the notebook over so that the rear ports are facing you and locate the memory module compartment. 3. Remove the screws that secure the RAM module compartment cover and set it aside in a safe place.
4. Remove the compartment cover and then angling it up and out. 5. If you need to install a higher capacity module, gently push the edge clips on both sides to release the module. Angle the card slightly upward and gently slide it from its edge connector slot. Store the card in the anti-static bag that contains your new module(s). 6. To install the new memory card, hold the card with its gold edge connector toward the edge connector slot of the compartment.
The Easy to Upgrade HDD Module The hard drive in your notebook computer is made to be easily swapped out for upgrading. You should back up your hard drive before attempting o change the hard drive. W WA AR RN NIIN NG G:: M ileess iinn Maakkee ssuurree tthhaatt bbeeffoorree yyoouu iinnssttaallll aa nneew w ddrriivvee,, aallll tthhee ffil yyoouurr ssyysstteem m sshhoouulldd bbee bbaacckkeedd uupp.. To upgrade your Hard Drive 78 1. Power down the system completely.
4. The drive is attached to a special bracket that secures it to the notebook computer. There are 4 screws hold the bracket. Remove the screws and set them in a safe place. 5. Push the HDD slightly in the direction of the arrow as shown in the illustration to release it from the pins of the drive. 6. Gently hold the grip of the HDD, lift it up to release from its compartment.
80 7. To install the new HDD, you will need to align the tabs on the drive bracket with the slots on the bay. Press down gently on the drive bracket until it engages with the system. Do not force the drive into place this can bend the pins on the hard drive. 8. Slide the compartment cover into place and be sure the screw holes on the cover align completely with the screw holes in the case. 9. Secure the cover with the three screws.
Upgrading your System CPU Refer to the following instructions and illustration for information on upgrading your notebook's CPU 1. Turn off the computer and disconnect the AC adapter and all peripherals. From the rear side of your notebook, use your index finger to lift up the hinge cover attached to the LCD screen. 2. Bend your LCD screen into 90 degree angle then carefully lift up the hinge cover.
82 3. Remove the screen that is attached to the keyboard in order to remove the heatsink on top of the CPU. 4. Remove all the screws attached to the heatsink. 5. Before removing the screws, there are certain measures to followed in removing the heatsink 6. To remove the heatsink, first loosen the screw carefully. 7. After loosening one screw, be certain that the next to be loosen should be the screw on its adjacent side as shown on the illustration.
Be sure to loosen all the screws first before removing it totally to release the heatsink. Failure to do so will cause a major damage to the heatsink. 8. Now you can totally remove all the screws also in that order when you first loosen the screw.
Appendix A Specification
Detailed Notebook Specifications General CPU • Intel Mobile Banias uFC-PGA2 1.3GHZ~1.7GHz CPU, 1MB L2 cache on die, CPU front-side bus up to 400MHz • 478 pin uFC-PGA2 478 socket Memory Main Memory • 2 expandable memory slot up to 2GB,1GB per DIMM Max. with 512Mb technology • • • • 128/ 256/ 512 MB memory options Two 200 pin SO DIMM type memory slots 2.
• • • • AGP v2.0 compliant 3.3V PCI version 2.2 compliance ACPI v2.0 USB 2.0 compatible Mass Storage HDD • Support Enhanced IDE (PIO mode 4) and bus master (Ultra DMA 33/66/100 mode) • Easily upgradable 2.5” 9.5mm HDD Module Bay • • Supports CD-ROM/ DVD-ROM/ Combo Drive; 5.25” 12.
• Built-in Intel ICH 4-M chipset Codec • Realtek ALC202A Features Dual full-duplex Direct Sound Channels Hardware SoundBlaster Pro for real-mode DOS legacy compatibility 18-bit ADC & DAC resolution Support S/PDIF out AC’97 2.
Features • High performance 3D graphics engine (floating triangle setup/ rendering) • Accelerated Graphic Port (AGP) 2.0 interface, 4X Graphic Memory • Integrate Video memory up to 32/64MB LCD Display • • Supports 15.0" TFT SXGA+/ 15.0" TFT XGA Models: 15.0” SXGA+ TFT --15.0" XGA TFT --14.
Dimensions • 326.0 mm (W) x 258.0 mm (D) x 25/32mm(H) • 12.83" (W) x 10.17" (D) x 0.99”(H) Weight • 2.7kg (5.9 lbs) with 14.1” panel, Battery and DVD-ROM Drive installed Operating Environment Temperature • Operating: 5°C ~ 35°C • Storage: -20°C ~ 60°C Humidity • Operating: • Non-operating: 10% ~ 90% (non-condensing) 30% ~ 90% (non-condensing) Altitude • Operating: • Non-operating: -200 to 30,000 feet above sea level.
• Memory Extension card • Module bay: CD-ROM/DVD-ROM/Combo (DVD-ROM+CD-RW) Drive Accessories • User's manual (option) • Driver CD title • AC adapter • Power cord • Battery pack Software Specifications System Software • System BIOS: AMI BIOS • Supported Operating Systems Optional Windows XP or above version Optional Windows 2000 or above version • Standard Software Drivers VGA driver Audio driver TouchPad driver IR driver (optional) Modem driver LAN driver AGP driver 90
91
