User's Manual

Questions? Call toll-free at 1-800-247-7285 Questions? Call toll-free at 1-800-247-7285
1
Connect the Gateway to a Computer
For All Users (Including Non-Windows Users)…
•
Wireless DSL
Gateway
•
Black Bag
•
Yellow Cable
•
Clear Bag
NEXT
Quick Start Guide
Wireless DSL Gateway
Questions? Call toll-free at 1-800-247-7285 Questions? Call toll-free at 1-800-247-7285 Questions? Call toll-free at 1-800-247-7285 Questions? Call toll-free at 1-800-247-7285 Questions? Call toll-free at 1-800-247-7285
Before connecting a Wireless Wireless DSL Gateway to a
Macintosh computer, the computer must be set up for network-
ing.Use the following procedure.
Step 1 Click the Apple in the
upper right corner of the menu
bar to reveal the
Apple Menu.
Step 2 From the Apple Menu,
click
Control Panels.
Step 3 From the Control
Panels
menu,click TCP/IP.
Step 4 When the TCP/IP
window appears,select Edit
from menu bar,then select
User Mode.
Step 5 When the User Mode
window appears,select
Advanced,then click OK.
Step 6 In the TCP/IP window,
select
Ethernet from the
Connect via pop-up menu.
Step 7 Select Using DHCP
Server
from the Configure
pop-up menu.
Step 8 Ensure the Use 802.3
option is Not checked.
Step 9 Click Options,and when
the
TCP/IP Options window
appears,select
Active.Make
sure the
Load only when
needed
option is Not checked,
then click
OK.
Step 10 Close the TCP/IP
window and when prompted
to save changes,click
Save.
Step 11 Restart the Computer.
The Computer is now set up
for networking.
Note: The procedure below is for the Macintosh operating systems version 9.2.2
and below.For computers running Macintosh OS X,see the User Manual.
Note: MSN Users with MAC OS-X and Later: In order to complete your MSN
installation and activate your MSN Account,insert the disk labeled “Windows
Users:Put this CD in FIRST”.
• Access your CD-ROM drive.
• Open the MSN for MAC folder.
• Double click on the “MSN for MAC OS X.dmg”file.
• Follow the instructions provided in the installation software.
Congratulations! You have successfully installed your Wireless
DSL Gateway.You can now access the Internet at high speed.
This Quick Start Guide will walk you through the
easy steps to set up your Wireless DSL Gateway.
During this process,we’ll show you how to:
Step 1 Click Setup in the top
menu.
Step 2 Click Advanced Setup
in the left-hand column of the
“Set Up/Configuration”screen.
Step 3 Click Begin Advanced
Setup
in the next screen.
Step 4 Click WAN IP Address
in the left-hand column of the
“Configuring the Advanced
Settings” screen.
Step 5 Make sure the circle
next to
Obtain an IP Address
through PPPoA
is selected.
Step 6 Check the box next to
Unnumbered Mode.
Step 7 Enter the
information for the
Unnumbered IP Address.
Click
Next.
Step 8 Enter your User Name
and Password.
Step 6 Enter your User Name,
Password
and Static IP address.
Step 9 Click Save and Restart
in the left-hand column.
Step 7 Click Save and Restart
in the left-hand column.
Step 1 Click Setup in the top
menu.
Step 2 Click Advanced Setup
in the left-hand column of the
“Set Up/Configuration”screen.
Step 3 Click Begin Advanced
Setup
in the next screen.
Step 5 Click the circle next to
the type of WAN IP Address
you have,then click
Next.
Step 4 Click WAN IP Address
in the left-hand column in the
“Configuring the Advanced
Settings” screen.
You will need the following items from your
Actiontec Quick Start Kit:
4
Configure a Block of IP Addresses
5
Configure a Single IP Address
6
Setup a Macintosh Computer
Part No.:0530-0427-001
Note: The information required to configure a single IP address is provided by
your ISP.If this information has not been provided, contact your ISP.
Note: The information required to configure a block of IP addresses is provided
by your ISP. If this information has not been provided,contact your ISP.
2
Install the Phone Filters
3
Configure the Gateway
4
Configure a Block of IP Addresses
5
Configure a Single IP Address
6
Setup a Macintosh Computer
QwstARK RedQS.qxd 12/2/03 11:20 AM Page 2