Bluetooth & AC97 Soft Modem OEM Installation Manual
Contents 1. 2. 3. 4. 5. 6.
2. Introduction Thank you for purchasing Actiontec Wireless Bluetooth and Modem Daughter Card. This manual will assist you with the installation procedure. The package you have received should contain the following items: • Bluetooth and Modem Daughter Card • OEM Installation Manual • Diskette containing AC97 Soft Modem driver, Wireless LAN Management utility and driver software.
3. Wireless Bluetooth Basics Wireless Bluetooth systems offer a great number of advantages over a traditional, wired system. Wireless Bluetooth are more flexible, easier to setup and manage and often more cost effective than their wired equivalence. Using radio frequency (RF) technology. Bluetooth transmits and receives data over the air, minimizing the need for wired connections. Thus, Bluetooth combines data connectivity with user mobility, and, through simplified configuration, enable movable LANs.
4. OEM Installation and Overview Here are some steps you will perform in establishing your wireless network connection: • Install software using the Installation Diskette. Here are some steps you will perform in installing your driver for AC97 Soft Modem. • Install driver using the Installation Diskette.
4.1 OEM Installation Procedures of Bluetooth and Modem Daughter Card Please follow the below steps one by one to install the utility and driver software successfully. 1. Insert the card into MDC slot, and take BT antenna to plug into RF connector. 2. Power on your PC and allow Windows to load fully. 3. Press once to turn on the Bluetooth device, LED on, and Windows first detects the USB device; click “cancel”. 4. Insert the given Installation diskette and then double click the setup.exe file to run setup.
4.2 OEM Installation Procedure of AC97 Soft Modem Please follow the below steps one by one to install the driver software successfully. 1. 2. 3. 4. 5. 6. 7. 8. Insert the card into MDC slot. Power on your PC and allow windows load fully. When Windows first detects the PCI Card or PCI device, click “Cancel”. Insert the given Installation diskette and then double click the setup.exe file to run setup. Click “OK” to start installation of modem driver.
5. Troubleshooting Bluetooth and Modem Daughter Card If you still encounter some problems while installing the Bluetooth and Modem Daughter Card utility and driver software or you want to confirm whether your software is installed properly or not, we have listed the procedure for checking the various components after you have installed the software. In section below, we have listed the various problems that you may encounter during the installation and have also listed the possible solution.
6. Technical Specification of Bluetooth Hardware compatibility • IBM-compatible computers Driver support • Windows 95 • Windows 98 • Windows NT4.0 • Windows 2000 • Windows Me Standards supported • Bluetooth spec. 1.1 • USB version 1.1 Environmental Operating temperature: • 0 degree Celsius to 70 degree Celsius (Operating) –20 to 85 (storing) • Max. Humidity 95 % Non-condensing Power specifications Operating voltage: • +5 V, +3.3V DC +- 5 % Radio specifications Range: • per cell indoors approx.
Mobility: • Seamless roaming across cell boundaries with handover Data encryption: • 40 bit WEP Encryption, 128-bit key length Utility software: • Link Config User setup & diagnostics tool Physical Dimensions • 47 x 28.5 x 4.6mm IO Connector • Hose Interface Connector: • Bluetooth RF Connector: • Modem Connector: Regulation • • • • FCC FCC Canada Europe • Japan • Other 40 Pin Hirose DF12-40DS-0.5V(89) connector to the host SMT Ultra Miniature coax RF connector, Hirose U.
Regulatory Compliance Notices Class B Equipment This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications.
United States 12
