Dome Camera Hardware Manual Z81, Z82, Z87 2022/03/09
Hardware Manual Table of Contents Precautions 3 Regulatory Compliance .................................................................... 4 Safety and Compliance Information ................................................ 5 Introduction 7 List of Models.................................................................................... 7 Package Contents ............................................................................. 8 Physical Description ..............................................
Hardware Manual Precautions Read these instructions Read all the safety and operating instructions before using this product. Heed all warnings Adhere to all the warnings on the product and in the instruction manual. Failure to follow the safety instructions given may directly endanger people, cause damage to the system or to other equipment. Servicing Do not attempt to service this product yourself as opening or removing covers may expose you to dangerous voltage or other hazards.
Hardware Manual Regulatory Compliance FCC Part 15 This equipment has been tested and found to comply with the limits for digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment.
Hardware Manual Safety and Compliance Information Installation and removal of the unit and its accessories must be carried out by qualified personnel. You must read all of the Safety Instructions supplied with your equipment before installation and operation. Installation This device is a class A product and may cause radio interference. Take measures if necessary. Make sure the camera operates in an environment where the temperature and humidity meet requirements.
Hardware Manual Maintenance If there is dust on the front glass surface, remove the dust gently using an oil-free brush or a rubber dust blowing ball. If there is grease or a dust stain on the front glass surface, clean the glass surface gently from the center outward using anti-static gloves or an oil-free cloth. If the grease or the stain still cannot be removed, use anti-static gloves or an oil-free cloth dipped with detergent and clean the glass surface gently until it is removed.
Hardware Manual Introduction List of Models This hardware manual contains the following models: Z81 Z82 Z87 2MP Outdoor Zoom Dome with D/N, Adaptive IR, Extreme WDR, SLLS, 4.4x Zoom Lens 4MP Outdoor Zoom Dome with D/N, Adaptive IR, Extreme WDR, SLLS, 4.4x Zoom Lens 4MP Outdoor Zoom Dome with D/N, Adaptive IR, Superior WDR, SLLS, 4.3x Zoom Lens 7 www.acti.
Hardware Manual Package Contents Contact your local dealer if the package is damaged or incomplete. The attachments may vary with models, please see the actual model for details. Camera Quick Installation Guide Screw Pack Drill Template Cable gland Physical Description Z81 / Z82 Item 1 Description DC 12V Power Input This connector is used to connect to a DC 12V power Jack adapter if a non-PoE network connection will be used.
Hardware Manual Z87 Item 1 Memory Card Slot Description Insert a memory card into this slot for local recording purposes. NOTE: Supports microSDHC and microSDXC cards. 2 Reset Button Press and hold to reset the camera to its default factory settings. 3 Built-in Microphone Receives audio input. 4 DC 12V Power Input This connector is used to connect to a DC 12V power Jack adapter if a non-PoE network connection will be used. Ethernet Port Connects to a network using an Ethernet cable.
Hardware Manual Installation Procedures Mounting on the Ceiling 1. Locate the positions of the holes; paste the drill template stickers on the surface and then use a Ø6-6.5mm drill bit to drill 30 mm-depth guide holes according to the positions marked by drill template. 2. Insert the plastic anchors and drill a hole to lead the cables out of the ceiling. 1 2 3. Loosen the fixing screw, then remove the housing. 1 10 www.acti.
Hardware Manual 4. Connect the cable and then secure the mounting base. Connect cable and protect it with waterproof tape (Optional) insert a micro SD card Attach bottom ring to ceiling with taping screws 5. Mount the camera to the base. Adjust the housing to the position shown in figure figure then push and turn it to anywhere but . 1 6. Adjust the lens viewing direction, and then tighten the screw. 11 www.acti.
Hardware Manual Waterproof RJ-45 Connector NOTE: The preceding installation process is for concealed installation, during which holes are punched on the wall and cables are penetrated into the wall. If open installation is adopted, cables are not penetrated into the wall but threaded out from the outlet on one side of the base. Seal ring 3 2 1 Attach the seal ring to the Ethernet interface. Mount the waterproof components in order.
Hardware Manual Access the Camera Configure the IP Addresses In order to be able to communicate with the camera from your PC, both the camera and the PC have to be within the same network segment. In most cases, it means that they both should have very similar IP addresses, where only the last number of the IP address is different from each other. There are 2 different approaches to IP Address management in Local Area Networks – by DHCP Server or Manually.
Hardware Manual Using the Default Camera IP Address If there is no DHCP server in the given network, the user may have to assign the IP addresses to both PC and camera manually to make sure they are in the same network segment. When the camera is plugged into network and it does not detect any DHCP services, it will automatically assign itself a default IP: 192.168.0.100 Whereas the default port number would be 80.
Hardware Manual Manually adjust the IP addresses of multiple cameras: If there are more than 1 camera to be used in the same local area network and there is no DHCP server to assign unique IP addresses to each of them, all of the cameras would then have the initial IP address of 192.168.0.100, which is not a proper situation for network devices – all the IP addresses have to be different from each other.
Hardware Manual Access the Camera Now that the camera and the PC are both having their unique IP addresses and are under the same network segment, it is possible to use the Web browser of the PC to access the camera. You can use Microsoft Internet Explorer to access the camera When using Internet Explorer browser, the ActiveX control for video stream management will be downloaded from the camera directly – the user just has to accept the use of such control when prompted so.
Hardware Manual Then use this newly setup Account and Password to login to the Web Configurator. 17 www.acti.
Copyright © 2022, ACTi Corporation All Rights Reserved 7F, No. 1, Alley 20, Lane 407, Sec. 2, Ti-Ding Blvd., Neihu District, Taipei, Taiwan 114, R.O.C. TEL : +886-2-2656-2588 FAX : +886-2-2656-2599 Email: sales@acti.
