KCM-7111 H.264 4-Megapixel IP D/N Vandal Proof PoE Rugged Dome Camera (DC 12V / PoE) Ver.
KCM-7111 Hardware User’s Manual Table of Contents 0. Precautions 3 1. Introduction 4 Package Contents ........................................................................... 4 Features and Benefits ..................................................................... 5 Safety Instructions .......................................................................... 6 Physical description ........................................................................ 8 Product Specification ................
KCM-7111 Hardware User’s Manual 0. Precautions Read these instructions You should read all the safety and operating instructions before using this product. Heed all warnings You must adhere to all the warnings on the product and in the instruction manual. Failure to follow the safety instruction given may directly endanger people, cause damage to the system or to other equipment.
KCM-7111 Hardware User’s Manual 1. Introduction Package Contents KCM-7111 *The lens is very stable and does not have focus shifts without screw, so no bundled screw for focus ring of the lens Product CD Terminal Blocks for Power DI/O and Audio Accessories Warranty Card Drill Template 4 www.acti.
KCM-7111 Hardware User’s Manual Features and Benefits This is a cutting edge network video surveillance camera. It can capture, compress and transmit real time video in excellent quality (8 FPS 4Megapixel, 2032 x 1920). This camera is your best choice to build an intelligent IP surveillance system. Adaptive Profile With the innovative embedded Image Signal Processor (ISP), this camera responds to changing lighting condition with customized algorithm.
KCM-7111 Hardware User’s Manual Software Development Kit Support This IP Box Camera can be integrated or controlled by applications from third party software developers. Software developers can save considerable efforts by using our Streaming Library or ActiveX control. Safety Instructions Don’t use the power supply with other voltages This device is likely to be damaged or damage other equipments / personnel, if you use a power supply with different voltage than the one included with this device.
KCM-7111 Hardware User’s Manual qualified service personnel under the following conditions. 1) When the power-supply cord or plug is damaged 2) If liquid has been spilled, or objects have fallen into the video product. 3) If the video product has been directly exposed to rain or water. 4) If the video product does not operate normally by following the operating Instructions in this manual.
KCM-7111 Hardware User’s Manual Physical description 1) Power Button Press the Power Button and then camera will reboot automatically. 2) Ethernet Port The IP device connects to the Ethernet via a standard RJ45 connector. Supporting NWAY, this IP device can auto detect the speed of local network segment (10Base-T/100Base-TX Ethernet).
KCM-7111 Hardware User’s Manual reset button. This length of time fluctuates slightly with the environment. The Power LED light will come back on and stay on after a few more seconds. The unit will start up with factory default settings automatically. Restore to Default Complete Power On On (3s) On 1s Off (about 15s) Off (10~15s) Stay On About 20 Seconds 5) Digital Input / Output Used in applications like motion detection, event triggering, time lapse recording, alarm notifications, etc.
KCM-7111 Hardware User’s Manual 6) DC 12V Power Input Connect DC power source to the terminal block. The wire with white dashed lines is the live wire, which should connect to the 12V pin. PIN NAME 1 N 2 L 3 GND DESCRIPTION AC Power Input E-Ground of power 7) Audio Input / Output The IP device supports audio input and output via terminal block 10 www.acti.
KCM-7111 Hardware User’s Manual Product Specification KCM-7111 • Device Device Type Image Sensor Sensor Size Horizontal Resolution Day / Night Minimum Illumination Color to B/W switch Mechanical IR Cut Filter IR Sensitivity Range IR LED Electronic Shutter Fixed Dome Camera BSI Progressive Scan CMOS 1/3.2 “ (4.5 x 3.4 mm) 1561 TVL Yes Color: 0.1 lux at F2.0 (30 IRE, 2400°K); B/W: 0.05 lux at F2.
KCM-7111 Hardware User’s Manual • Alarm Alarm Trigger Alarm Response Video motion detection 3 regions in single view mode, 1 region each in 4 cropped VGA mode; External device through digital input Notify control center; Change camera settings; Command other devices; E-mail notification with snapshots; Save video or snapshot to local storage; Upload video, snapshot to FTP server; Activate external device through digital output • Interface Iris Connector Digital Input Digital Output Local Storage Extern
KCM-7111 Hardware User’s Manual 2. Installation Procedure Connecting the IP Outdoor Rugged Dome 1) Remove the cover Remove the dome cover with special hex wrench in the accessory kit. 2) Insert the cable There are two conduit holes on this rugged dome. One is at the bottom, while the other is at the side and covered with a plug.
KCM-7111 Hardware User’s Manual How to Do the Waterproof Installation The following installation procedure makes the camera be water-resistant even for the situations where the camera can easily be flooded by pouring rain. The important part to focus on during the installation: The protection of the cabling has to be done by a proper flex conduit. The size of the flex conduit that matches with the conduit gland is is 3/4” (trade size), or with actual physical diameter of 26.441mm.
KCM-7111 Hardware User’s Manual Scenario 1 – using the side hole. Scenario 2 – using the bottom hole. Screw the body of the conduit gland into the camera and fix it with the lock nut (included in the set of conduit gland that you purchased) from the inside of the camera.. Connect the Ethernet cable to the camera’s network port. If you are not using PoE, then please remember to pull the DC power cable through the flex conduit as well, and connect to the camera at this point. 15 www.acti.
KCM-7111 Hardware User’s Manual Push the head of the flex conduit, wrapped with sealing insert, into the body of the conduit gland. Screw the clamping nut tightly onto the body of the conduit gland. Adjust the viewing angle and focus of the camera and put the dome cover back on, and tighten it by using the screws. You have completed a fully waterproof installation! 16 www.acti.
KCM-7111 Hardware User’s Manual 3. Accessing Camera If you have DHCP server / router in your network: Many network server / routers are able to automatically provide IP addresses through DHCP. If you are using such a network, just plug in your computer and IP Box Cam into the network and your IP device will acquire network address by itself. Find and access the device with our IP Utility program. You may download it at: http://www.acti.
KCM-7111 Hardware User’s Manual 4. Open Internet Explorer (Version 6.0 or above) , and type in the Default IP: 192.168.0.100 5. When you see the login window, please input default user and password: Default User: Admin Password: 123456 6. After logging in, you will see the video from camera. To go to the main menu, click the ”Setup” button on the top left. 18 www.acti.
KCM-7111 Hardware User’s Manual If you are using a single camera, this is enough to access the device. If you are using multiple devices, you need to change the current device to another unused IP address, so that when the next device is connected to the network, no two devices use the same IP. Please perform the following steps. 7. Go to Network -> Connection Type 8. Change the IP mode to Static. 9. Change the IP to 192.168.0.101 or any other unused IPs. Do NOT use the PC’s IP address or 192.168.0.
