E43 5MP Bullet with D/N, IR, Basic WDR, Vari-focal lens Hardware User’s Manual (PoE) Ver.
E43 Hardware User’s Manual Table of Contents 0. Precautions 3 1. Introduction 4 Package Contents ........................................................................... 4 Features and Benefits ..................................................................... 5 Safety Instructions .......................................................................... 6 Physical description ........................................................................ 8 Basic Connections .........................
E43 Hardware User’s Manual 0. Precautions Read these instructions You should read all the safety and operating instructions before using this product. Heed all warnings You must adhere to all the warnings on the product and in the instruction manual. Failure to follow the safety instruction given may directly endanger people, cause damage to the system or to other equipment.
E43 Hardware User’s Manual 1. Introduction Package Contents E43 (Included camera stand/sun shield) Accessories Conduit Gland Warranty Card QIG 4 www.acti.
E43 Hardware User’s Manual Features and Benefits This is a cutting-edge digital video surveillance camera. It can compress and transmit real time images with outstanding image quality through a standard TCP/IP network. This camera is your best choice to build an intelligent IP surveillance system. H.264 High Profile/MJPEG Multi-Codec Dual Streaming This device supports 2 compression formats, H.264 High Profile and MJPEG.
E43 Hardware User’s Manual Safety Instructions Don’t open the housing of the product Cleaning Disconnect this video product from the power supply before cleaning. Attachments Do not use attachments not recommended by the video product manufacturer as they may cause hazards. Water and Moisture Do not use this video product near water, for example, near a bathtub, washbowl, kitchen sink, or laundry tub, in a wet basement, or near a swimming pool and the like.
E43 Hardware User’s Manual Safety Check Upon completion of any service or repairs to this video product, ask the service technician to perform safety checks to determine if the video product is in proper operating condition. 7 www.acti.
E43 Hardware User’s Manual Physical description 1) Reset Button Step 1: Press and continue to hold the Reset Button for 15 seconds (with a sharp tipped object, like a pen.) after the unit has successfully completed the boot process. Step 2: The Ethernet LED light will turn off for about 1~2 seconds and flash on for another second. By this time the reset to default operation is already completed. You may then release the reset button. This length of time fluctuates slightly with the environment.
E43 Hardware User’s Manual Basic Connections Follow the procedures below to connect the IP device to the respective apparatuses. Please use a PoE (Power over Ethernet) supported switch or injector: 1) Connect your IP Camera to the PoE Switch / Injector by CAT5 or CAT6 cables with RJ45 connector. 2) Connect your PoE Switch / Injector to PC with another CAT5 / CAT6 network cable. 9 www.acti.
E43 Hardware User’s Manual Product Specification E43 • Device Device Type Bullet Camera Image Sensor Progressive Scan CMOS Day / Night Minimum Illumination Color to B/W switch Yes Color: 0.1 lux at F1.
E43 Hardware User’s Manual 2. Installation How to Do the Waterproof with Conduit Installation Beside the bundled network cable, you also can use conduit and follow the installation procedure to make the camera be water-resistant even for the situations where the camera can easily be flooded by pouring rain. The important part to focus on during the installation: The protection of the cabling has to be done by a proper flex conduit. The size of the flex conduit that matches with the conduit gland is 1/2”.
E43 Hardware User’s Manual 3. Remove the bundled network cable and connector from back side cover of the camera. 4. The third piece of conduit gland goes through the back side cover of the camera. 5. The fourth piece (locking nut) is used to lock the gland firmly from the inside of the back side cover. 6. Pull the network cable through the back side cover of the camera. 7. Connect the flex conduit to the back side cover of the camera. 12 www.acti.
E43 Hardware User’s Manual 8. Tighten the domed sealing nut. 9. Plug the network cable into the camera’s RJ-45 connector before closing the back side of the camera. If you are not using PoE and need an additional power cord then please connect it at this stage, too. 10. Tighten the screws of the back side of the camera properly. 11. Finally, the bullet camera with properly mounted flex conduit as well as with proper outdoor bracket would look like this.
E43 Hardware User’s Manual How to replace pre-installed network cable with cable gland The camera bundled cable gland with pre-installed network cable is M20 X 1.5 Matric thread. It is resistant to salt water, weak acid, alcohol, oil, grease and common solvency. The cable gland consists of five parts: Lock Nut, Body, Seal, Claw and Sealing Nut as shown below.
E43 Hardware User’s Manual The following images show the step-by-step procedure of replacing network cable and completing the water-proof installation. 1.Open the back side cover from camera, and remove the network cable, and loosen the sealing nut to release the network cable from camera. 2.Separate the seal from the claw. 1 2 2 2 3.Squeeze the seal and then pull out the bundled network cable. 4.
E43 Hardware User’s Manual 5.Assemble the Seal and Claw, and then Insert the 2 network cable to RJ-45 PoE connector. 2 1 2 6. Tighten the screws of the back side cover on the camera properly 7.Tighten the sealing nut as far as possible. 8.Finally, the bullet camera is now properly mounted with waterproof cabling and is ready to attach to the proper outdoor bracket. 16 www.acti.
E43 Hardware User’s Manual 3.Accessing Camera If you have DHCP server / router in your network: Many network server / routers are able to automatically provide IP addresses through DHCP. If you are using such a network, just plug in your computer and IP Camera into the network and your IP device will acquire network address by itself. Find and access the device with our IP Utility program. You may download it at: http://www.acti.com/Utility If you do NOT have DHCP server / router in your network: 1.
E43 Hardware User’s Manual Please set the settings as below. IP address: 192.168. 0.xxx Subnet mask: 255.255.255. 0 (NOTE: xxx should be a number from 1 to 254 except 100, which is used by the IP device. Please also make sure that no two equipments use the same IP address in the same network.) 4. Open Internet Explorer (Version 6.0 or above) , and type in the Default IP: 192.168.0.100 5.
E43 Hardware User’s Manual 6. After logging in, you will see the video from camera. To go to the main menu, click the “Setup” button on the top left. If you are using a single camera, this is enough to access the device. If you are using multiple devices, you need to change the current device to another unused IP address, so that when the next device is connected to the network, no two devices use the same IP. Please perform the following steps. 7. Go to IP Settings -> Connection Type 8.
E43 Hardware User’s Manual 10. Click “Apply” 11. Please go to System -> Save & Reboot, and click “Apply”. Internet Explorer will close after a few seconds. This is normal. 12. Wait for 30 seconds, and open IE again to connect to the new IP. (In this example, 192.168.0.101). For the second device or more you add into the network, please type the correct IP. 13. Adjust the default Video setting by going to Video -> Video Please refer the firmware manual for the detail information. 20 www.acti.
