D12 1MP Cube with Fixed lens Hardware User’s Manual (PoE) Ver.
D11 Hardware User’s Manual Table of Contents Precautions 3 Safety Instructions ........................................................................... 4 Introduction 6 Features and Benefits ...................................................................... 6 Package Contents............................................................................. 7 Physical Description ........................................................................ 8 Mount Type ....................................
D11 Hardware User’s Manual Precautions Read these instructions You should read all the safety and operating instructions before using this product. Heed all warnings You must adhere to all the warnings on the product and in the instruction manual. Failure to follow the safety instruction given may directly endanger people, cause damage to the system or to other equipment.
D11 Hardware User’s Manual interference at their own expense. Safety Instructions Don’t open the housing of the product Cleaning Disconnect this video product from the power supply before cleaning. Attachments Do not use attachments not recommended by the video product manufacturer as they may cause hazards. Water and Moisture Do not use this video product near water, for example, near a bathtub, washbowl, kitchen sink, or laundry tub, in a wet basement, or near a swimming pool and the like.
D11 Hardware User’s Manual Safety Check Upon completion of any service or repairs to this video product, ask the service technician to perform safety checks to determine if the video product is in proper operating condition. 5 www.acti.
D11 Hardware User’s Manual Introduction Features and Benefits This is a cutting-edge digital video surveillance camera. It can compress and transmit real time images with outstanding image quality through a standard TCP/IP network. This camera is your best choice to build an intelligent IP surveillance system. H.264 High Profile/MJPEG Multi-Codec Dual Streaming This device supports 2 compression formats, H.264 High Profile and MJPEG.
D11 Hardware User’s Manual Package Contents Cube Camera Bracket Screw kit QIG Warranty Card 7 www.acti.
D11 Hardware User’s Manual Physical Description 1) Reset Button The Reset button is used to reset the camera to its default factory settings, if necessary. To reset the camera: Step 1: Press and continue to hold the Reset Button for 15 seconds (with a sharp tipped object, like a pen.) after the unit has successfully completed the boot process. Step 2: The Ethernet LED light will turn off for about 1~2 seconds and flash on for another second.
D11 Hardware User’s Manual Mount Type Ceiling Mount Wall Mount 9 www.acti.
D11 Hardware User’s Manual Installation Step 1: Mount the Camera 1. Mount the Bracket The bracket can be mounted on a concrete or wooden wall or ceiling. Select the location where you want to mount the bracket. When mounting on a concrete wall or ceiling 1. Mark the location of the three screw holes on the wall or ceiling and drill the holes. 2. Insert the supplied plastic washer into each hole. 10 www.acti.
D11 Hardware User’s Manual 3. Using a Phillips screwdriver, attach the three supplied screws to secure the bracket to the wall or ceiling. When mounting on a wooden wall or ceiling 1. Place the bracket on the desired mounting location on the wall or ceiling. 2. Using a Phillips screwdriver, screw the supplied screws through the screw holes of the bracket and the wall or ceiling. 11 www.acti.
D11 Hardware User’s Manual 2. Install the Camera 1. Screw the camera to the bracket. 2. Position the camera to face the target view area. 12 www.acti.
D11 Hardware User’s Manual 3. Tighten the know to fix the camera position. 13 www.acti.
D11 Hardware User’s Manual Step 2: Connect the Camera To connect the camera, you need to prepare the following: Power over Ethernet (PoE) supported switch (to connect multiple cameras) or PoE injector (to connect a single camera) Ethernet cables Connecting a Single Camera To connect a single camera, use a PoE injector to supply both data and power to the camera using one Ethernet cable. Follow the procedures below: 1. Connect the camera to the PoE injector using an Ethernet cable. 2.
D11 Hardware User’s Manual Connecting Multiple Cameras To connect multiple cameras, use a PoE switch. 1) Connect the camera(s) to the PoE switch using Ethernet cables. 2) Connect the PoE switch to a network and an AC power source. 3) Connect a PC to the same network.
D11 Hardware User’s Manual Accessing Camera If you have DHCP server / router in your network Many network server / routers are able to automatically provide IP addresses through DHCP. If you are using such a network, just plug in your computer and IP Camera into the network and your IP device will acquire network address by itself. Find and access the device with our IP Utility program. You may download it at: http://www.acti.
D11 Hardware User’s Manual Please set the settings as below. IP address: 192.168. 0.xxx Subnet mask: 255.255.255.0 (NOTE: xxx should be a number from 1 to 254 except 100, which is used by the IP device. Please also make sure that no two equipments use the same IP address in the same network..) 4. Open Internet Explorer (Version 6.0 or above) , and type in the Default IP: 192.168.0.100 5.
D11 Hardware User’s Manual 6. After logging in, you will see the video from camera. To go to the main menu, click the “Setup” button on the top left. If you are using a single camera, this is enough to access the device. If you are using multiple devices, you need to change the current device to another unused IP address, so that when the next device is connected to the network, no two devices use the same IP. Please perform the following steps. 7. Go to IP Settings -> Connection Type 8.
D11 Hardware User’s Manual 10. Click “Apply” 11. Please go to System -> Save & Reboot, and click “Apply”. Internet Explorer will close after a few seconds. This is normal. 12. Wait for 30 seconds, and open IE again to connect to the new IP. (In this example, 192.168.0.101). For the second device or more you add into the network, please type the correct IP. 13. Adjust the default Video setting by going to Video -> Video Please refer the firmware manual for the detail information. 19 www.acti.
