Wireless Cube Camera Hardware Manual C11W Ver.
Hardware Manual Table of Contents Precautions 3 Safety Instructions ........................................................................... 5 Introduction 6 List of Models.................................................................................... 6 Package Contents............................................................................. 7 Physical Description ........................................................................ 8 Basic Connections 10 Connecting the Antenna .....
Hardware Manual Precautions Read these instructions You should read all the safety and operating instructions before using this product. Heed all warnings You must adhere to all the warnings on the product and in the instruction manual. Failure to follow the safety instruction given may directly endanger people, cause damage to the system or to other equipment.
Hardware Manual Federal Communications Commission Statement This equipment has been tested and found to comply with the limits for a class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications.
Hardware Manual Safety Instructions Don’t open the housing of the product Cleaning Disconnect this video product from the power supply before cleaning. Attachments Do not use attachments not recommended by the video product manufacturer as they may cause hazards. Water and Moisture Do not use this video product near water, for example, near a bathtub, washbowl, kitchen sink, or laundry tub, in a wet basement, or near a swimming pool and the like.
Hardware Manual Introduction List of Models This hardware manual contains the following models: C11W 1.3MP Wireless Cube with Basic WDR, Fixed lens 6 www.acti.
Hardware Manual Package Contents Camera Antenna Power Adapter Bracket Mounting Screws Quick Installation Guide Warranty Card 7 www.acti.
Hardware Manual Physical Description Item Description 1 DC 12V Power Connects to the power adapter to supply power to the camera. 2 Ethernet Port Connects to a network using a standard Ethernet cable. There are two (2) LED indicators on the Ethernet port that indicate the camera status: Power / Wireless LED (Amber) o Solid LED: Power is on and camera is ready. o Flashing LED: Wireless connection is in progress. The flashing speed indicates the speed of the wireless connection (slow or fast).
Hardware Manual Item 6 Reset Button Description Restores the camera to its factory default settings. How to reset the camera? 1. Power off the camera. 2. Press and hold the RESET button as you power on the camera. 3. Continuously press the RESET button until the Amber LED lights up which will normally take about 30 seconds to complete. 9 www.acti.
Hardware Manual Basic Connections Connecting the Antenna 1. Screw the antenna to the antenna jack. 2. Turn the antenna to its vertical position. Connecting to Power Connect one end of the bundled power adapter to the camera DC 12V jack and the other end to a power outlet. 10 www.acti.
Hardware Manual Connecting to a Wired Network Connect one end of an Ethernet cable to the LAN port of the camera and the other end to a network switch. Connecting Audio Output Device (optional) If necessary, connect the audio out device jack to the audio out port of the camera. Installing the Memory Card (optional) 1. Insert the memory card with the metal contacts facing the back of the camera. 11 www.acti.
Hardware Manual 2. Push the card until it clicks into place. NOTE: Supports microSDHC cards only. 12 www.acti.
Hardware Manual Installing the Camera Mounting the Bracket Attach the bracket to the wall using the three (3) supplied screws. Mounting the Camera 1. Attach the camera to the bracket and tighten the knob. 2. Adjust the tilt angle and tighten the knob to fix the camera position. 13 www.acti.
Hardware Manual Adjusting the Viewing Angle and Focus Based on the live view, adjust the camera viewing angle and focus to get the target view. 1. Loosen the knob and tilt the camera towards the target view. 2. Tighten the knob to fix the camera position. 3. The camera comes with a pre-fixed focus applicable for most environments. If there is a need make adjustments when viewing the camera Live View, turn the lens left or right to adjust the focus. 14 www.acti.
Hardware Manual Connecting for the First Time When setting up the camera for the first time, the setup must be done by wired connection using Ethernet even if the camera will be used wirelessly. To do the initial setup, the camera and the PC must be connected to the same network access point, such as a router. Also, set the PC default browser to Microsoft Internet Explorer. 1. Plug the camera power adapter to the power source. Once the camera is powered up, the power LED (amber) lights up. 2.
Hardware Manual 5. On the Login page, enter the default Account and Password and then click Login. Account: admin Password: 123456 NOTE: Install ActiveX Control for video streaming management when prompted in Internet Explorer. 6. After login, the Live View page is displayed. Click the SETUP icon. 7. From the SETUP menu, click IP Settings > WiFi. 16 www.acti.
Hardware Manual 8. Setting up wireless connection can be managed by one of the following ways: Wi-Fi Protected Setup (WPS) or Manual Setup. A. Wi-Fi Protected Setup (WPS): WPS provides simple and secure wireless connection between the devices by pressing the WPS button on both devices. The router must have a WPS button (refer to Router documentation for details) to use this feature. To connect or pair devices by WPS: a. Press the WPS button on the router. b.
Hardware Manual B. Manual Setup: This function searches for the wireless network and lets the user to manually configure the wireless settings by entering the security mode, passcode and other required parameters to connect to the network. a. On the WiFi page, click Search to list the available networks within the camera range. b. Click the SSID, commonly known as the network name of the wireless network that you want to connect to. c.
Hardware Manual e. Then, click Apply to connect to the wireless network. Once the camera is successfully connected, the Amber LED will flash quickly. f. Disconnect the Ethernet cable from the camera. Wireless setup is complete. g. Access the camera via wireless network connection. See Accessing the Camera on page 20. NOTE: For more detailed information, refer to the Firmware Manual downloadable from www.acti.com. 19 www.acti.
Hardware Manual Accessing the Camera To access the camera live view, the camera and the PC must belong to the same network. A sample connection diagram is shown below. The quickest way to discover the cameras in the network is to use the simplest network search, built in the Windows system. In Windows system, click Network and double-click on the camera model to launch the default browser of the PC with the IP address of the target camera filled in the address bar of the browser already.
Hardware Manual Search and downloand the latest IP Utility from http://www.acti.com/DownloadCenter. Upon launching of IP Utility, an instant report will be shown as follows: You can quickly notice the camera model in the list. Click on the IP address to automatically launch the default browser of the PC with the IP address of the target camera filled in the address bar of the browser already. The user interface called Web Configurator appears with the Login page.
Copyright © 2016, ACTi Corporation All Rights Reserved 7F, No. 1, Alley 20, Lane 407, Sec. 2, Ti-Ding Blvd., Neihu District, Taipei, Taiwan 114, R.O.C. TEL : +886-2-2656-2588 FAX : +886-2-2656-2599 Email: sales@acti.
