ACM-3011 IP IR DN PoE Fixed Dome with Vari-focal Lens Hardware User’s Manual (DC 12V / PoE) Ver.
ACM-3011 Hardware User’s Manual Table of Contents 0. Precautions 3 1. Introduction 4 Package Contents ........................................................................... 4 Features and Benefits ..................................................................... 5 Safety Instructions .......................................................................... 6 Physical description ........................................................................ 8 Installation Procedure ...............
ACM-3011 Hardware User’s Manual 0. Precautions Read these instructions You should read all the safety and operating instructions before using this product. Heed all warnings You must adhere to all the warnings on the product and in the instruction manual. Failure to follow the safety instruction given may directly endanger people, cause damage to the system or to other equipment.
ACM-3011 Hardware User’s Manual 1. Introduction Package Contents ACM-3011 Power Adaptor (Optional) Product CD Accessories Warranty Card Drill Template Drill template 4 www.acti.
ACM-3011 Hardware User’s Manual Features and Benefits This is a cutting-edge digital video surveillance camera. It can compress and transmit real time images with outstanding image quality (30 FPS @ VGA, 640x480) through a standard TCP/IP network. This camera is your best choice to build an intelligent IP surveillance system. MPEG-4/MJPEG Dual Codec Compression This device supports two compression formats, MPEG-4 and MJPEG.
ACM-3011 Hardware User’s Manual Safety Instructions Don’t use the power supply with other voltages This device is likely to be damaged or damage other equipments / personnel, if you use a power supply with different voltage than the one included with this device. All warranty of this product will be voided in the situations above. Cleaning Disconnect this video product from the power supply before cleaning.
ACM-3011 Hardware User’s Manual Safety Check Upon completion of any service or repairs to this video product, ask the service technician to perform safety checks to determine if the video product is in proper operating condition. 7 www.acti.
ACM-3011 Hardware User’s Manual Physical description 1) Ethernet Port The IP device connects to the Ethernet via a standard RJ45 connector. Supporting NWAY, this IP device can auto detect the speed of local network segment (10Base-T/100Base-TX Ethernet). 2) Power Input Connect the power adaptor here if your power input is DC12V.
ACM-3011 Hardware User’s Manual Step 3: Reconnect the power cable while continuing to hold the reset button. The red Power LED light will flash on for 3 second first, turn off for about 15 seconds, flash on for another second and turn off again. By this time the reset to default operation is already completed. This will take around 20 seconds from power up. You may then release the reset button. This length of time fluctuates slightly with the environment.
ACM-3011 Hardware User’s Manual will detect the change in digital input and transmit the signal to video surveillance servers. Terminal Pin Define is described as below: Pin Name Description Spec DIO PW Electrically connected in parallel with the con- Voltage: 12V DC, nector for the power supply, this pin provides an Max: 1.2W auxiliary connector for mains power to the unit. This pin can also be used to power auxiliary equipment, with a maximum current of 100mA.
ACM-3011 Hardware User’s Manual Installation Procedure Ceiling Mount Use the drill template, and drill a hole with φ 35 on the ceiling Tighten the plate to ceiling with M4*20 screws 11 www.acti.
ACM-3011 Hardware User’s Manual Connect cables through the hole on the ceiling and plate, or on the side of casing Fasten the camera to ceiling by turning clockwise direction 12 www.acti.
ACM-3011 Hardware User’s Manual Insert the cables (Power/Network/DIO/Audio) through the mounting plate and connect to the camera. Then use the little strap in bundled accessory to fasten the network cable. 1.6.1.6 Done 13 www.acti.
ACM-3011 Hardware User’s Manual Wall Mount Tighten wall mount bracket to the wall by 3 PAN Head Tapping screws 3-PAN HEAD SCREW TAPPING Tighten the plate to wall mount bracket with M4*10 screws, and connect all necessary cables through the hole on the plate and wall mount kit 2-FLAT HEAD SCREW TAPPING(M4x10) 14 www.acti.
ACM-3011 Hardware User’s Manual Note: that there’s a triangle mark on both plate and wall mount kit. Those triangle marks need to be fixed to the same direction. Insert the cables (power/Network/audio) through the mounting plate and connect to the camera. Then use the little strap in bundled accessory to fasten the network cable. 15 www.acti.
ACM-3011 Hardware User’s Manual Fasten the camera to wall mount kit by turning clockwise direction Done 16 www.acti.
ACM-3011 Hardware User’s Manual Basic Connections Follow the procedures below to connect the IP device to the respective apparatuses. If you have a PoE(Power over Ethernet) supported switch or injector: 1) Connect your IP Camera to the Switch / Injector by CAT5 or CAT6 cables with RJ45 connector. 2) Connect your Switch / Injector to PC with another CAT5 / CAT6 network cable.
ACM-3011 Hardware User’s Manual Product Specification ACM-3011 Device Image Micron Progressive Scan CMOS Size 1/3 inch Effective Pixels Color 640(H) x 480(V) Color mode automatically switched to B/W mode under 4 Lux B/W Min. Scene Illumination 0 Lux (IR LED ON) IR Sensitivity from 700nm to 1100nm IR LED IR LED x24 (850nm) CDS Sensor Yes IR Working Distance Lens 10 ~ 20 M (30 IRE) Focal Length f3.3 ~ 12mm / F1.6 Viewing Angle 75.4º ~ 22.
ACM-3011 Hardware User’s Manual 2. Accessing Camera If you have DHCP server / router in your network: Many network server / routers are able to automatically provide IP addresses through DHCP. If you are using such a network, just plug in your computer and IP Camera into the network and your IP device will acquire network address by itself. Find and access the device with our IP Utility program. You may download it at: http://www.acti.
ACM-3011 Hardware User’s Manual 4. Open Internet Explorer (Version 6.0 or above) , and type in the Default IP: 192.168.0.100 5. When you see the login window, please input default user and password: Default User: Admin Password: 123456 6. After logging in, you will see the video from camera. To go to the main menu, click the ”Setup” button on the top left. 20 www.acti.
ACM-3011 Hardware User’s Manual If you are using a single camera, this is enough to access the device. If you are using multiple devices, you need to change the current device to another unused IP address, so that when the next device is connected to the network, no two devices use the same IP. Please perform the following steps. 7. Go to Setup -> WAN Setting 8. Choose Static IP Address. 9. Change the IP to 192.168.0.101 or any other unused IPs. Do NOT use the PC’s IP address or 192.168.0.100.).
ACM-3011 Hardware User’s Manual 12. Wait for 30 seconds, and open IE again to connect to the new IP. (In this example, 192.168.0.101). For the second device or more you add into the network, please type the correct IP. 13. Adjust the video stream by going to Video Setting 22 www.acti.
