access control TECHNOLOGY Operating & Installation Instructions for ACTSmart 2 Product Range
ACTSmart2 Operating and Installation Manual Rev. 1.0 Contents Installation Notes ....................................................................................................4 Product Specification..............................................................................................4 30 Second Programming Guide..............................................................................5 Programming Summary....................................................................................
ACTSmart2 Operating and Installation Manual Rev. 1.0 Installation Notes • Remember to Factory Default the ACTSmart before programming • Remember to place the supplied varistor across the terminals of the door strike coil to protect the relay contacts • Don’t mount the ACTSmart Prox units near RF sources (Eg mobile phones, radio transmitters, computer monitors) or metal surfaces. • Remember that the ACTSmart PIN and Prox units default to Card operation. Card and PIN operation must be programmed in.
ACTSmart2 Operating and Installation Manual Rev. 1.0 30 Second Programming Guide (For typical Standalone System) 1. Enter Programming Mode. Press ✘ button followed by the programming code (default is 9999) The LED will flash amber. 2. Add a Batch of Cards (ACT 1080 only) Press 10, then present the first card in the batch followed by the last card in the batch. Press ✔ button to complete. 3. Add a PIN Code Press 12, and then enter a 4-digit PIN code. Press ✔ button to complete.
ACTSmart2 Operating and Installation Manual Rev. 1.
ACTSmart2 Operating and Installation Manual Rev. 1.0 ACTSmart Operation The ACTSmart family consists of Proximity only, Pin and Proximity and PIN only units. Each ACTSmart can operate in standalone mode. Up to 8 ACTSmart devices can be connected on a RS485 network. The ACTSmart will support a maximum of 1000 tokens. A token may be a card or a PIN code. Each unit is contained in a rugged polycarbonate housing, with stainless steel keys and potted electronics, allowing for indoor and outdoor installation.
ACTSmart2 Operating and Installation Manual Rev. 1.0 Adding a Card Batch: Step 1 2 3 4 5 Keypad Entry Operation 10 Present Card Present Card Enter 1-8, (optional)* Press ✔ Add Card Batch First card in Batch (lowest number card) Last Card in Batch (highest number card) Select each door this batch enabled for End programming card batch Note: the buzzer will sound while cards are loaded into memory.
ACTSmart2 Operating and Installation Manual Rev. 1.0 Adding a Card Batch using the keypad: Step 1 2 3 4 5 Keypad Entry 16 Enter 10-digit card number Enter 10-digit card number 1-8, (optional)* Press ✔ Operation Add Card Batch 10-digit First Card number with leading zeros. Eg. Card 54321 enter 0000054321. Second Card number Select each door to which these cards are enabled End Adding Card Batch — Note: the buzzer will sound while cards are loaded into memory.
ACTSmart2 Operating and Installation Manual Rev. 1.0 Change Programming Code: Step 1 2 Keypad Entry Operation 23 0001-9999 Change Programming code New 4 - 6 digit programming code Change Number of PIN Digits: Step 1 2 Keypad Entry Operation 24 4-6 Change Number of PIN digits Select number of PIN digits in range 4 to 6. When set, the codes require leading zeros Eg. Code 9999 becomes 009999 for 6 digits.
ACTSmart2 Operating and Installation Manual Rev. 1.
ACTSmart2 Operating and Installation Manual Rev. 1.
ACTSmart2 Operating and Installation Manual Rev. 1.
ACTSmart2 Operating and Installation Manual Rev. 1.
ACTSmart2 Operating and Installation Manual Rev. 1.0 Programming a Network System Up to 8 ACTSmart devices can be connected on the network. See the ACTSmart Network Installation diagram to complete the necessary connections. Programming Door Numbers To allow some users through a door and prevent access to other users, each ACTSmart on the network must be given a door number (1-8). An ACTSmart Proximity Only Unit requires a door number if it is to be programmed with advanced options.
ACTSmart2 Operating and Installation Manual Rev. 1.0 Find Door Number: Step Keypad Entry 1 61 2 1-8 3 Press a key or present a card Operation Find Door Numbers Enter the door number to be found. The ACTSmart assigned the door number starts to beep. To stop the ACTSmart beeping.
ACTSmart2 Operating and Installation Manual Rev. 1.0 Programming ACTSmart Prox Only To program an ACTSmart Prox Only device, a Programming Card must be assigned to the ACTSmart. The Programming Card may be any proximity card. To set the Programming Card into the ACTSmart Prox, power up the device with the tamper open (by removing the main unit from the mounting plate or the surface mount collar), and immediately present a card twice.
Access Control Technology, Unit 8, Tallaght Business Park, Whitestown, Dublin 24, Ireland. Tel: 353-1-4622585 Fax: 353-1-4622587 Web: http://www.accesscontrol.ie E-mail: sales@accesscontrol.
Access Control Technology, Unit 8, Tallaght Business Park, Whitestown, Dublin 24, Ireland. Tel: 353-1-4622585 Fax: 353-1-4622587 Web: http://www.accesscontrol.ie E-mail: sales@accesscontrol.
SHIELD SHIELDS DC Power Supply Unit SHIELD Continue daisy chain to remaining ACTSmart units on the network (maximum 8). Access Control Technology, Unit 8, Tallaght Business Park, Whitestown, Dublin 24, Ireland. Tel: 353-1-4622585 Fax: 353-1-4622587 Web: http://www.accesscontrol.ie E-mail: sales@accesscontrol.ie Do NOT use AC Power Supply. MUST be 12V or 24V DC. DC Power Supply Unit Total cable length maximum 1.4km Network cable is single shielded twisted pair, Belden 9501 or similar.
SCREWS Place the Reader / Keypad onto the surface mount collar and clip down into place. Use the security screw supplied to attach the unit to the surface mount collar. Place the cap onto the unit and push firmly into place. Security screw supplied with the unit. Access Control Technology, Unit 8, Tallaght Business Park, Whitestown, Dublin 24, Ireland. Tel: 353-1-4622585 Fax: 353-1-4622587 Web: http://www.accesscontrol.ie E-mail: sales@accesscontrol.
Place the Reader / Keypad onto the surface mount collar and clip down into place. Use the security screw supplied to attach the unit to the surface mount collar. Place the cap onto the unit and push firmly into place. Security screw supplied with the unit. Access Control Technology, Unit 8, Tallaght Business Park, Whitestown, Dublin 24, Ireland. Tel: 353-1-4622585 Fax: 353-1-4622587 Web: http://www.accesscontrol.ie E-mail: sales@accesscontrol.
ACTSmart2 Operating and Installation Manual Rev. 1.
Smart access control TECHNOLOGY User List User Name Card Number PIN Doors 1 2 3 4 5 6 7 8 Access Control Technology, Unit 8, IDA Business Park, Whitestown, Dublin 24, Ireland. TEL:353-1-4622585 FAX: 353-1-4622587 WEB: http://www.accesscontrol.ie E-MAIL: sales@ accesscontrol.
