Operating & Installation Instructions for ACTsmart Product Range 18-00052
ACTsmart Operating and Installation Manual Rev. 1.2 Contents ORDERING INFORMATION ............................................................................................2 INSTALLATION NOTES ....................................................................................................3 IMPORTANT ........................................................................................................................3 PRODUCT SPECIFICATION ..........................................................
ACTsmart Operating and Installation Manual Rev. 1.2 • Remember to Factory Default the ACTsmart before programming Installation Notes • Remember to place the supplied varistor across the terminals of the door strike coil to protect the relay contacts • Don’t mount the ACTsmart Prox units near RF sources (Eg mobile phones, radio transmitters, computer monitors) or metal surfaces. • Remember that the ACTsmart PIN and Prox units default to Card operation. Card and PIN operation must be programmed in.
ACTsmart Operating and Installation Manual Rev. 1.2 30 Second Programming Guide (For typical Standalone System) 1. Enter Programming Mode. Press ✘ button followed by the programming code (default is 9999) The LED will flash amber. 2. Add a Batch of Cards Press 10, then present the first card in the batch followed by the last card in the batch. Press ✔ button to complete. 3.
ACTsmart Operating and Installation Manual Rev. 1.
ACTsmart Operating and Installation Manual Rev. 1.2 ACTsmart Operation The ACTsmart family consists of Proximity Only (ACTSmart 1070), Pin and Proximity (ACTsmart 1080) and PIN Only (ACTsmart 1090) units. Each ACTsmart can operate in standalone mode. Up to 8 ACTsmart devices can be connected on a RS485 network. The ACTsmart supports 500 users. Each unit is contained in a rugged polycarbonate housing, with stainless steel keys and potted electronics, allowing for indoor and outdoor installation.
ACTsmart Operating and Installation Manual Step Keypad Entry Operation 10 Present Card Present Card Enter 1-8, (optional)* Press ✔ Add Card Batch First card in Batch (lowest number card) Last Card in Batch (highest number card) Select each door this batch enabled for End programming card batch Note: the buzzer will sound while cards are loaded into memory.
ACTsmart Operating and Installation Manual Step 1 2 Rev. 1.2 3 4 5 Keypad Entry 16 Enter 10-digit card number Enter 10-digit card number 1-8, (optional)* Press ✔ Operation Add Card Batch 10-digit First Card number with leading zeros. Eg. Card 54321 enter 0000054321. Last Card number Select each door this Card is deleted from End Adding Card Batch Step 1 2 Keypad Entry 17 Enter 10-digit card number Operation Delete Card or Card and PIN 10-digit Card number with leading zeros. Eg.
ACTsmart Operating and Installation Manual Step 1 2 3 4 Keypad Entry 30-41 0 or 1 1-8, (optional)* Press ✔ Rev. 1.
ACTsmart Operating and Installation Manual Rev. 1.
ACTsmart Operating and Installation Manual Step Rev. 1.
ACTsmart Operating and Installation Manual Rev. 1.2 Programming a Network System Up to 8 ACTsmart devices can be connected on the network. See the ACTsmart Network Installation diagram to complete the necessary connections. Programming Door Numbers To allow some users through a door and prevent access to other users, each ACTsmart on the network must be given a door number (1-8). An ACTsmart Proximity Only Unit requires a door number if it is to be programmed with advanced options.
ACTsmart Operating and Installation Manual Step Keypad Entry 1 61 2 1-8 Find Door Number: 3 Step Press a key or present a card Keypad Entry Find All Door Numbers: Rev. 1.2 Operation Find Door Numbers Enter the door number to be found. The ACTsmart assigned the door number starts to beep. To stop the ACTsmart beeping.
ACTsmart Operating and Installation Manual Rev. 1.2 from the mounting plate or the surface mount collar). Within 10 seconds of power up carry out the following actions. 2. Present the card to the reader. 3. Take the card away from the reader for 1 second (more than 20 cm) 4. Within a further 10 seconds replace LK1. The reader will beep. The card is now set as the Programming card. (Note: ACT recommends using an ACTsmart PIN and Prox device if a network is required).
Access Control Technology, Unit C1, South City Business Centre, Tallaght, Dublin 24, Ireland. Tel: 353-1-4662570 Fax: 353-1-4520427 UK Locall: 0845 300 5204 Web: http://www.accesscontrol.ie E-mail: sales@accesscontrol.
Access Control Technology, Unit C1, South City Business Centre, Tallaght, Dublin 24, Ireland. Tel: 353-1-4662570 Fax: 353-1-4520427 UK Locall: 0845 300 5204 Web: http://www.accesscontrol.ie E-mail: sales@accesscontrol.
Access Control Technology, Unit C1, South City Business Centre, Tallaght, Dublin 24, Ireland. Tel: 353-1-4662570 Fax: 353-1-4520427 UK Locall: 0845 300 5204 Web: http://www.accesscontrol.ie E-mail: sales@accesscontrol.
Access Control Technology, Unit C1, South City Business Centre, Tallaght, Dublin 24, Ireland. Tel: 353-1-4662570 Fax: 353-1-4520427 UK Locall: 0845 300 5204 Web: http://www.accesscontrol.ie E-mail: sales@accesscontrol.
Access Control Technology, Unit C1, South City Business Centre, Tallaght, Dublin 24, Ireland. Tel: 353-1-4662570 Fax: 353-1-4520427 UK Locall: 0845 300 5204 Web: http://www.accesscontrol.ie E-mail: sales@accesscontrol.
Smart User List User Name Card Number PIN Doors 1 2 3 4 5 6 7 Access Control Technology, Unit C1, South City Business Centre, Tallaght, Dublin 24, Ireland. Tel: 353-1-4662570 Fax: 353-1-4520427 UK Locall: 0845 300 5204 Web: http://www.accesscontrol.ie E-mail: sales@accesscontrol.
