Operating & Installation Instructions for ACTSmart Product Range
ACTSmart Operating and Installation Manual Rev 1.1 Contents Installation Notes…...………………………………………………. Product Specification ………………………………………………. 30 Second Programming Guide…………………………………….. Programming Summary…………………………………………….. ACTSmart Operation…...…………………………………………... ACTSmart Programming………………………………...…………. Adding a Card Batch……………………… … ……………… Deleting a Card Batch………………………………………… Adding a Pin…………………………………………………... Deleting a Pin………………………………………………..... Adding a Card and Pin …………………………………...… ..
ACTSmart Operating and Installation Manual Rev 1.1 Installation Notes • Remember to Factory Default the ACTSmart before programming • Remember to place the supplied varistor across the terminals of the door strike coil to protect the relay contacts • Don’t mount the ACTSmart Prox units near RF sources (Eg mobile phones, radio transmitters, computer monitors) or metal surfaces. • Remember that the ACTSmart PIN and Prox units default to Card operation. Card and PIN operation must be programmed in.
ACTSmart Operating and Installation Manual Rev 1.1 30 Second Programming Guide (For typical Standalone System) 1. Enter Programming Mode. Press ✘ button followed by the programming code (default is 9999) The LED will flash amber. 2. Add a Batch of Cards Press 10, then present the first card in the batch followed by the last card in the batch. Press ✔ button to complete. 3.
ACTSmart Operating and Installation Manual Rev 1.
ACTSmart Operating and Installation Manual Rev 1.1 ACTSmart Operation The ACTSmart family consists of Proximity only, Pin and Proximity and PIN only units. Each ACTSmart can operate in standalone mode. Up to 8 ACTSmart devices can be connected on a RS485 network. The ACTSmart will support 500 Card Holders and/or 500 PIN users. Each unit is contained in a rugged polycarbonate housing, with stainless steel keys and potted electronics, allowing for indoor and outdoor installation.
ACTSmart Operating and Installation Manual Adding a Card Batch: Step Keypad Entry 1 10 2 Present Card 3 Present Card 4 Enter 1-8, (optional)* 5 Press ✔ Operation Add Card Batch First card in Batch (lowest number card) Last Card in Batch (highest number card) Select each door this batch enabled for End programming card batch – Note: the buzzer will sound while cards are loaded into memory.
ACTSmart Operating and Installation Manual Rev 1.1 Adding a Card Batch using the keypad: Step Keypad Entry Operation 1 16 Add Card Batch 2 Enter 10-digit card number 10-digit First Card number with leading zeros. Eg. Card 54321 enter 0000054321.
ACTSmart Operating and Installation Manual Rev 1.
ACTSmart Operating and Installation Manual Rev 1.
ACTSmart Operating and Installation Manual Quick IO Setup: Step Keypad Entry 1 53 2 0-9 0 1 2 3 4 5 6 7 8 9 3 4 1-8 (optional)* Press ✔ Rev 1.
ACTSmart Operating and Installation Manual Rev 1.1 Programming a Network System Up to 8 ACTSmart devices can be connected on the network. See the ACTSmart Network Installation diagram to complete the necessary connections. Programming Door Numbers To allow some users through a door and prevent access to other users, each ACTSmart on the network must be given a door number (1-8). An ACTSmart Proximity Only Unit requires a door number if it is to be programmed with advanced options.
ACTSmart Operating and Installation Manual Rev 1.1 Find Door Number: Step Keypad Entry 1 61 2 1-8 3 Operation Find Door Numbers Enter the door number to be found. The ACTSmart assigned the door number starts to beep.
ACTSmart Operating and Installation Manual Rev 1.1 Programming ACTSmart Prox Only To program an ACTSmart Prox Only device, a Programming Card must be assigned to the ACTSmart. The Programming Card may be any proximity card. If you have a received a batch of cards, use the first (lowest numbered) card in the batch as the Programming Card.
ACTSmart Standalone Installation Diagram +V Default configuration for AUX I/O 2 is Door Alarm. + OM RO N 1A 125V AC 1A 30V DC Sounder Default configuration for Programmable Input is Door Release Button. Aux I/O 2 12-24V DC/AC 12V = DC 5A/250V ~AC A +12V SCHRACK - 15 - B Door Release Button The ACTSmart may be powered from 12 or 24V AC or DC for Standalone operation. OM RN O 5A 250V AC 5A 30V DC The Aux I/O Output is an open collector output capable of sinking 100mAmps.
ACTSmart Fire Alarm Override Connections Fire Alarm Panel Common the 0V line of each ACTSmart to avoid Ground Loop issues. System Ok 01X X -1 P R ODUC T : AC T S mart R E V 1.3 NUMB ER : 00X X X X B A T C H: S E R IA L S E R IA L 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 01X X -1 P R ODUC T : AC T S mart R E V 1.3 NUMB ER : 00X X X X OMR ON A ux I /O 1 - 16 - Constant 0V supplied to the ACTSmart AUX I/O from the fire alarm panel. If 0V is removed, the doors open.
ACTSmart Network Installation Diagram Note: When networking the ACTSmart units, common the 0V of each ACTSmart to avoid ground loop issues. Continue daisy-chain to remaining ACTSmart units on the network (maximum 8). Network cable is single shielded twisted pair, Belden 9501 or similar. T otal c able length maximum 1.4km -17- A B SHIE L D A SHIE L D SHIE L DS B B A T C H: 01X X -1 P R ODUC T : AC T S mart R E V 1.3 00X X X X B A T C H: 01X X -1 P R ODUC T : AC T S mart R E V 1.
ACTSmart Mounting Instructions for Flush-Mount Unit Spacers break away from main component when required by installer for use. Standard pattress box. View showing spacers stacking View showing mounting plate before spacers are broken - 18 Magnet in mounting plate, which keeps tamper switch closed inside ACTSmart Note: Determine the distance between the pattress box and the mounting plate, using the spacers which are labeled 1mm to 4mm.
ACTSmart Mounting Instructions for Surface Mount Unit Magnet in surface mount collar, which keeps tamper switch closed inside ACTSmart. - 19 - Security screw supplied with the unit. The surface mount collar is mounted on the wall using the fixing kit supplied in the box. Place the cap onto the unit and push firmly into place. Place the Reader / Keypad onto the surface mount collar and clip down into place. Use the security screw supplied to attach the unit to the surface mount collar.
User List User Name Card Number PIN 1 2 3 Doors 4 5 6 7 Access Control Technology, Unit 8, IDA Business Park, Whitestown, Dublin 24, Ireland. TEL:353-1-4622585 FAX: 353-1-4622587 WEB: http://www.accesscontrol.ie E-MAIL: sales@ accesscontrol.
