User's Manual
Table Of Contents
- T3CAS_Section_5
- 5 Adjustment/Test
- 1. General
- 2. Equipment
- 3. Initial Harness Checkout (New Installations Only)
- 4. System Self-Tests
- 5. Return-to-Service Test
- 6. Operational Software Loading Using an ARINC 615A Portable Data Loader or Compact Flash Card
- 7. Downloading Information from the TP3PCAS Using a CF Card
- 1. Obtain a New or Blank Compact Flash (CF) card.
- 2. Copy to the New or Blank CF card the appropriate ‘Header File’
- a) Header files are files copied to the New or Blank CF card that will instruct the computer unit what is desired to be downloaded.
- b) Header files needed to download Maintenance Data, Event Data and CRC Part Numbers can be obtained from ACSS Customer Services at +1-623-445-7070 or crc.acss@l-3com.com.
- 3. For downloading Maintenance Data, Event Data or CRC Part Numbers the aircraft does not need to be in an on-ground configuration.
- 4. Apply power to the computer unit.
- 5. Insert the CF card.
- 6. For ACSS part numbers 9005000-10000, -10101, -10202, and -10204 the DATA STATUS LED will UblinkU green once; this indicates the unit recognized that a CF card was inserted.
- 7. For ACSS part numbers 9005000-11203, -11801 and -55801 the DATA STATUS LED will UblinkU green while reading the header file and performing the action defined in the header file.
- 8. Flight Data Recording
- 1. T3CAS part numbers 9005000-10000, -10101, -10202, and -10204 only support FAT16 CF card formatting. T3CAS part numbers 9005000-11203, -11801 and -55801 support both FAT16 and FAT32 CF card formatting.
- B. Flight Data
- 1. Obtain a New or Blank CF Card.
- 2. Copy to the New or Blank CF Card the Appropriate Header File.
- 3. Header files are files copied to the New or Blank CF card that will instruct the computer unit what is desired to be downloaded.
- 4. For Flight Data Recording, the aircraft does not need to be in an on-ground configuration.
- 5. Apply power to the computer unit.
- 6. Insert the CF card.
- B. Flight Data
- 9. Downloaded Maintenance Data, Event Data And Flight Data May Be Sent To ACSS Customer Services For Analysis
- 5 Adjustment/Test
- T3CAS_Section_6
- T3CAS_Section_7
- 7 Maintenance Practices
- 1. General
- 2. Equipment and Materials
- 3. Procedure for the TP3PCAS Computer Unit
- 4. Procedure for the APM (Not applicable for part numbers 9005000-10000, -10101, -10202, -10204, or -11203)
- 5. Procedure for the Directional Antenna
- 6. Procedure for the Omnidirectional Antenna (Applicable to part numbers 9005000-11203, -11801 and -55801)
- 7. Procedure for the Control Panel
- 8. Procedure for the VSI/TRA Display
- 9. Instructions for Continued Airworthiness, FAR Part 25.1529
- 7 Maintenance Practices
- T3CAS_Section_8
- T3CAS_Section_9
- T3CAS_Section_10
- T3CAS_Appendix_A
SYSTEM DESCRIPTION AND INSTALLATION MANUAL
T
3
CAS/Part No.9005000
Table 4-8: Operator Selectable Options – Default Settings (cont)
Operator Selectable
Options
Data Parameter Selectable Option
Basic Runway
Inhibition
Annunciation
BASIC_RUNWAY_INHIB_ANNUN
The zero (0) state is
the disabled state for
this option. The one (1)
state enables the
”TERR N/A”
annunciator to activate
when GCAM indicates
Basic Airport.
2500ft/Radio Altitude
Valid Aural
RADIO_ALTITUDE_VALID_AURAL
This setting defines the
verbal transmission
(words) intended to
occur during this radio
altitude-triggered
callout.
Windshear Caution
Disable
WINDSHEAR_CAUTION_DISABLE
Not selectable by
customer.
Windshear Caution
Aural Disable
WINDSHEAR_CAUTION_AURAL_DISABLE
Not selectable by
customer.
Windshear Caution
Aural
WINDSHEAR_CAUTION_AURAL
Not selectable by
customer.
Obstacle Enable OBSTACLE_ENABLE
Enable - enables
obstacle algorithm.
Obstacle Maximum
Display Range
OBSTACLE_MAX_DISPLAY_RANGE
The Obstacle Maximum
Display Range
represents the
maximum range setting
for the display at which
non-alerting obstacles
will be displayed. When
the display range is set
greater than this value,
all non-alerting
obstacles will be
removed.
If the value of Obstacle
Maximum Display
Range is not equal to
5NM, 10NM, 15NM,
20NM, 25NM, 40NM,
80NM, 160NM, or
320NM, a setting of
10NM is used for a
default
Pub. No. 8600200-001, Revision 004
34-45-29
4-107
04 Nov 2014
Use or disclosure of information on this page is subject to the restrictions in the proprietary notice of this document.