User's Manual
Table Of Contents
- T3CAS_Section_5
- 5 Adjustment/Test
- 1. General
- 2. Equipment
- 3. Initial Harness Checkout (New Installations Only)
- 4. System Self-Tests
- 5. Return-to-Service Test
- 6. Operational Software Loading Using an ARINC 615A Portable Data Loader or Compact Flash Card
- 7. Downloading Information from the TP3PCAS Using a CF Card
- 1. Obtain a New or Blank Compact Flash (CF) card.
- 2. Copy to the New or Blank CF card the appropriate ‘Header File’
- a) Header files are files copied to the New or Blank CF card that will instruct the computer unit what is desired to be downloaded.
- b) Header files needed to download Maintenance Data, Event Data and CRC Part Numbers can be obtained from ACSS Customer Services at +1-623-445-7070 or crc.acss@l-3com.com.
- 3. For downloading Maintenance Data, Event Data or CRC Part Numbers the aircraft does not need to be in an on-ground configuration.
- 4. Apply power to the computer unit.
- 5. Insert the CF card.
- 6. For ACSS part numbers 9005000-10000, -10101, -10202, and -10204 the DATA STATUS LED will UblinkU green once; this indicates the unit recognized that a CF card was inserted.
- 7. For ACSS part numbers 9005000-11203, -11801 and -55801 the DATA STATUS LED will UblinkU green while reading the header file and performing the action defined in the header file.
- 8. Flight Data Recording
- 1. T3CAS part numbers 9005000-10000, -10101, -10202, and -10204 only support FAT16 CF card formatting. T3CAS part numbers 9005000-11203, -11801 and -55801 support both FAT16 and FAT32 CF card formatting.
- B. Flight Data
- 1. Obtain a New or Blank CF Card.
- 2. Copy to the New or Blank CF Card the Appropriate Header File.
- 3. Header files are files copied to the New or Blank CF card that will instruct the computer unit what is desired to be downloaded.
- 4. For Flight Data Recording, the aircraft does not need to be in an on-ground configuration.
- 5. Apply power to the computer unit.
- 6. Insert the CF card.
- B. Flight Data
- 9. Downloaded Maintenance Data, Event Data And Flight Data May Be Sent To ACSS Customer Services For Analysis
- 5 Adjustment/Test
- T3CAS_Section_6
- T3CAS_Section_7
- 7 Maintenance Practices
- 1. General
- 2. Equipment and Materials
- 3. Procedure for the TP3PCAS Computer Unit
- 4. Procedure for the APM (Not applicable for part numbers 9005000-10000, -10101, -10202, -10204, or -11203)
- 5. Procedure for the Directional Antenna
- 6. Procedure for the Omnidirectional Antenna (Applicable to part numbers 9005000-11203, -11801 and -55801)
- 7. Procedure for the Control Panel
- 8. Procedure for the VSI/TRA Display
- 9. Instructions for Continued Airworthiness, FAR Part 25.1529
- 7 Maintenance Practices
- T3CAS_Section_8
- T3CAS_Section_9
- T3CAS_Section_10
- T3CAS_Appendix_A
SYSTEM DESCRIPTION AND INSTALLATION MANUAL
T
3
CAS/Part No.9005000
Table 4-1: T
3
CAS Computer Unit Interface Description (cont)
(Applicable to Part No. 9005000-10000, -10101, -10202, -10204, and -11203)
Connector
Pin
Designation
Functional Description
RMP-10A
RMP-10B
Reserved Program Pin Inputs
Reserved for future use.
RMP-10C
APM Installed Program Input (NO)
A ground on this pin indicates that an Aircraft Personality Module (APM) is
connected to the T
3
CAS.
RMP-10D
Reserved
RMP-10E
Reserved
RMP-10F
Reserved
RMP-10G
Reserved
RMP-10H
Traffic Selection Device Input #2 (Rotate Right)
RMP-10J
Traffic Selection Device Input #2 (Rotate Left)
RMP-10K
Traffic Selection Device #1 Push Button
RMP-11A
Reserved
RMP-11B
Reserved
RMP-11C
Male Voice Program Input
This program input is intended to allow audio annunciation to be selectable for
either male or female genders. A ground on this pin selects the male voice and an
open selects the female voice.
RMP-11D
Flight Data Recorder ARINC 429 and Extended Maintenance Log Program
Input
This program pin is used to specify whether the ARINC 429 Flight Data Recorder
(FDR) is to be used. An open on this pin means that the FDR is not utilized. A
ground indicates that flight data is output as high-speed ARINC 429 data on RA
Display No.1 and No.2 busses. While the FDR is enabled, normal low-speed RA
display bus operation is not available. A ground also enables RA/TA events
recording in memory.
RMP-11E,
11F
ARINC 429 Input: MMR/GPS #1 [RMP-11E (A), RMP-11F (B)]
This high-speed 429 input is used to receive GPS label input containing position,
velocity and quality information for the use of ADS-B IN applications and by the
transponder function of ADS-B OUT.
Pub. No. 8600200-001, Revision 004
34-45-29
4-17
04 Nov 2014
Use or disclosure of information on this page is subject to the restrictions in the proprietary notice of this document.