User's Manual
Table Of Contents
- T3CAS_Section_5
- 5 Adjustment/Test
- 1. General
- 2. Equipment
- 3. Initial Harness Checkout (New Installations Only)
- 4. System Self-Tests
- 5. Return-to-Service Test
- 6. Operational Software Loading Using an ARINC 615A Portable Data Loader or Compact Flash Card
- 7. Downloading Information from the TP3PCAS Using a CF Card
- 1. Obtain a New or Blank Compact Flash (CF) card.
- 2. Copy to the New or Blank CF card the appropriate ‘Header File’
- a) Header files are files copied to the New or Blank CF card that will instruct the computer unit what is desired to be downloaded.
- b) Header files needed to download Maintenance Data, Event Data and CRC Part Numbers can be obtained from ACSS Customer Services at +1-623-445-7070 or crc.acss@l-3com.com.
- 3. For downloading Maintenance Data, Event Data or CRC Part Numbers the aircraft does not need to be in an on-ground configuration.
- 4. Apply power to the computer unit.
- 5. Insert the CF card.
- 6. For ACSS part numbers 9005000-10000, -10101, -10202, and -10204 the DATA STATUS LED will UblinkU green once; this indicates the unit recognized that a CF card was inserted.
- 7. For ACSS part numbers 9005000-11203, -11801 and -55801 the DATA STATUS LED will UblinkU green while reading the header file and performing the action defined in the header file.
- 8. Flight Data Recording
- 1. T3CAS part numbers 9005000-10000, -10101, -10202, and -10204 only support FAT16 CF card formatting. T3CAS part numbers 9005000-11203, -11801 and -55801 support both FAT16 and FAT32 CF card formatting.
- B. Flight Data
- 1. Obtain a New or Blank CF Card.
- 2. Copy to the New or Blank CF Card the Appropriate Header File.
- 3. Header files are files copied to the New or Blank CF card that will instruct the computer unit what is desired to be downloaded.
- 4. For Flight Data Recording, the aircraft does not need to be in an on-ground configuration.
- 5. Apply power to the computer unit.
- 6. Insert the CF card.
- B. Flight Data
- 9. Downloaded Maintenance Data, Event Data And Flight Data May Be Sent To ACSS Customer Services For Analysis
- 5 Adjustment/Test
- T3CAS_Section_6
- T3CAS_Section_7
- 7 Maintenance Practices
- 1. General
- 2. Equipment and Materials
- 3. Procedure for the TP3PCAS Computer Unit
- 4. Procedure for the APM (Not applicable for part numbers 9005000-10000, -10101, -10202, -10204, or -11203)
- 5. Procedure for the Directional Antenna
- 6. Procedure for the Omnidirectional Antenna (Applicable to part numbers 9005000-11203, -11801 and -55801)
- 7. Procedure for the Control Panel
- 8. Procedure for the VSI/TRA Display
- 9. Instructions for Continued Airworthiness, FAR Part 25.1529
- 7 Maintenance Practices
- T3CAS_Section_8
- T3CAS_Section_9
- T3CAS_Section_10
- T3CAS_Appendix_A
SYSTEM DESCRIPTION AND INSTALLATION MANUAL
T
3
CAS/Part No.9005000
CLEANING/PAINTING
1. General
While the T
3
CAS Integrated Platform is installed in the aircraft, cleaning is limited to the
procedures given below. Painting and more extensive cleaning should be done during shop
maintenance when the LRUs can be disassembled. Detailed instructions are given in each
applicable component-level maintenance manual.
2. Equipment and Materials
WARNING: BEFORE YOU USE A MATERIAL, REFER TO THE MANUFACTURER’S
MATERIAL SAFETY DATA SHEETS FOR SAFETY INFORMATION. SOME
MATERIALS CAN BE DANGEROUS.
Table 9-1 gives the equipment and materials required for cleaning and painting.
Table 9-1: Equipment and Materials
Name
Description
Source
Abrasive paper
No.600, nonconductive abrasive
Optional source
Air supply
Air ionizing nozzle gun attachment
for compressed air (20 PSI)
Optional source
Cleaning brush
Soft, natural-bristle
(camel's hair)
Optional source
Glass cleaner
Ammoniated
Optional source
Lens tissue
Lint Free
Optional source
Sandpaper
Grit sizes 220 and 400
Optional source
AMN 110C878
Catalyst, polyurethane — No.
V66V44(-4)
Sherwin-Williams Co,
Cleveland, OH
AMN 1113678
Solvent —Isopropanol alcohol,
technical grade
Optional source
Lint free cloth
Lint free cloth
Optional source
AMN 94C2178
Coating, Prolane 2.8TPLUS
polyurethane, semigloss WHT,
FED-STD--595, Color No.27925—
No.F63EXW968--4380
Sherwin-Williams Co,
Cleveland, OH
Pub. No. 8600200-001, Revision 004
34-45-29
9-1
04 Nov 2014
Use or disclosure of information on this page is subject to the restrictions in the proprietary notice of this document.