User's Manual
Table Of Contents
- T3CAS_Section_5
- 5 Adjustment/Test
- 1. General
- 2. Equipment
- 3. Initial Harness Checkout (New Installations Only)
- 4. System Self-Tests
- 5. Return-to-Service Test
- 6. Operational Software Loading Using an ARINC 615A Portable Data Loader or Compact Flash Card
- 7. Downloading Information from the TP3PCAS Using a CF Card
- 1. Obtain a New or Blank Compact Flash (CF) card.
- 2. Copy to the New or Blank CF card the appropriate ‘Header File’
- a) Header files are files copied to the New or Blank CF card that will instruct the computer unit what is desired to be downloaded.
- b) Header files needed to download Maintenance Data, Event Data and CRC Part Numbers can be obtained from ACSS Customer Services at +1-623-445-7070 or crc.acss@l-3com.com.
- 3. For downloading Maintenance Data, Event Data or CRC Part Numbers the aircraft does not need to be in an on-ground configuration.
- 4. Apply power to the computer unit.
- 5. Insert the CF card.
- 6. For ACSS part numbers 9005000-10000, -10101, -10202, and -10204 the DATA STATUS LED will UblinkU green once; this indicates the unit recognized that a CF card was inserted.
- 7. For ACSS part numbers 9005000-11203, -11801 and -55801 the DATA STATUS LED will UblinkU green while reading the header file and performing the action defined in the header file.
- 8. Flight Data Recording
- 1. T3CAS part numbers 9005000-10000, -10101, -10202, and -10204 only support FAT16 CF card formatting. T3CAS part numbers 9005000-11203, -11801 and -55801 support both FAT16 and FAT32 CF card formatting.
- B. Flight Data
- 1. Obtain a New or Blank CF Card.
- 2. Copy to the New or Blank CF Card the Appropriate Header File.
- 3. Header files are files copied to the New or Blank CF card that will instruct the computer unit what is desired to be downloaded.
- 4. For Flight Data Recording, the aircraft does not need to be in an on-ground configuration.
- 5. Apply power to the computer unit.
- 6. Insert the CF card.
- B. Flight Data
- 9. Downloaded Maintenance Data, Event Data And Flight Data May Be Sent To ACSS Customer Services For Analysis
- 5 Adjustment/Test
- T3CAS_Section_6
- T3CAS_Section_7
- 7 Maintenance Practices
- 1. General
- 2. Equipment and Materials
- 3. Procedure for the TP3PCAS Computer Unit
- 4. Procedure for the APM (Not applicable for part numbers 9005000-10000, -10101, -10202, -10204, or -11203)
- 5. Procedure for the Directional Antenna
- 6. Procedure for the Omnidirectional Antenna (Applicable to part numbers 9005000-11203, -11801 and -55801)
- 7. Procedure for the Control Panel
- 8. Procedure for the VSI/TRA Display
- 9. Instructions for Continued Airworthiness, FAR Part 25.1529
- 7 Maintenance Practices
- T3CAS_Section_8
- T3CAS_Section_9
- T3CAS_Section_10
- T3CAS_Appendix_A
SYSTEM DESCRIPTION AND INSTALLATION MANUAL
T
3
CAS/Part No.9005000
CPA Warning (Audio Menu Selection programming Pin is a don’t care) - “AVOID
TERRAIN”
Note that a single “TERRAIN AHEAD, PULL-UP, AVOID TERRAIN” or “TERRAIN
TERRAIN, PULL-UP, PULL-UP, AVOID TERRAIN” is provided when an Avoid Terrain
condition exist before a Pull-Up occurs.
Mode 1 Caution (Audio Menu Selection programming Pin is a don’t care) - “SINK RATE”
Mode 1 warning (Audio Menu Selection programming Pin is a don’t care) -
“PULL-UP PULL-UP”
Mode 2 Caution (Audio Menu Selection programming Pin is a don’t care) -“TERRAIN
TERRAIN”
Mode 2 Warning (Audio Menu Selection programming Pin is a don’t care) -“PULL-UP
PULL-UP”
Mode 3 Warning (Audio Menu Selection programming Pin is a don’t care) - “DON’T
SINK”
Mode 4 Warning (Audio Menu Selection programming Pin is a don’t care) - “TOO LOW
GEAR” or “TOO LOW TERRAIN” or “TOO LOW FLAPS”
Mode 5 Warning (Audio Menu Selection programming Pin is a don’t care) -
“GLIDESLOPE GLIDESLOPE”
(3) Spare/CRT-LCD Display Select/Alternate Lamp Format. (See Table 4-21).
Table 4-21: CRT-LCD Display Select and Alternate Lamp Format
(Applicable to 9005000-10000, -10101, -10202, -10204, and -11203)
Configuration
Number
Spare
CRT-LCD
Display
Alternate
Lamp
Format
State
Connect RTP-
7A to:
1 Disable CRT Format 2 000 Open
2 Disable CRT Format 1 001 RTP-13B
3
Disable
LCD
Format 2
010
RTP-13C
4
Disable
LCD
Format 1
011
RTP-13D
5 (Spare Conf.)
Enable
CRT
Format 2
100
RTP-13E
6 (Spare Conf.) Enable CRT Format 1 101 RTP-13F
7 (Spare Conf.) Enable LCD Format 2 110 RTP-13G
8 (Spare Conf.)
Enable
LCD
Format 1
111
RTP-13H
9 (Invalid)
Invalid
Invalid
Invalid
NA
RTP-13K
CRT-LCD DISPLAY:
Terrain display is either CRT or LCD.
ALTERNATE LAMP FORMAT:
Lamp Format 1 - the warning alert discreet output (RTP-13D) are grounded for
any alert except the Mode 5 (Glideslope alert) and the caution alert discrete
output (RTP-13B) is grounded for Mode 5 (Glideslope) alert only.
4-124
04 Nov 2014
34-45-29
Pub. No. 8600200-001, Revision 004
Use or disclosure of information on this page is subject to the restrictions in the proprietary notice of this document.